ICP DAS USA PCI-1002 LU User manual

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [email protected]
The package includes the following items:
One PCI/PEX-1002 series board as follows:
PCI-1002LU, PCI-1002HU
PEX-1002L, PEX-1002H
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
One CA-4002 D-Sub connector
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
For PCI-1002 LU/HU
PEX-1002 L/H
What’s in the shipping package?
English/ Jun. 2013/ Version 1.0
Installing Windows Driver

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The PCI-1002 series classic driver supports Windows 98/NT/2K and 32-bit
XP/ 2003/ Vista/7/8. Recommended to install this driver for have been
used PCI-1002 series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pci-1002/manual/quicksta
rt/classic/
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Jumper Setting
1
2
3
4
1. CON3: Analog Input
2. CON2: Digital Input
3. CON1: Digital Output
4. JP1: A/D Input Type Selection
5. SW1: Card ID Setting for PEX-1002 only
6. PCI Bus: for PCI-1002 only
PCI Express: for PEX-1002 only
6
5

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Please make sure JP1 jumper and SW1 is kept in default setting before
self-test, as follows:
Jumper
JP1: Analog Input Type Selection
Single-Ended Inputs (Default)
Differential Inputs
Switch
SW1: Card ID Setting
Card ID
1
ID0
2
ID1
3
ID2
4
ID3
(*) 0
ON
ON
ON
ON
1
OFF
ON
ON
ON
2
ON
OFF
ON
ON
:
:
:
:
:
0xD
OFF
ON
OFF
OFF
0xE
ON
OFF
OFF
OFF
0xF
OFF
OFF
OFF
OFF
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI/PCI Express slot.
Step 4: Carefully insert your I/O card into the PCI/PCI Express slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
Installing Hardware on PC
(*) Default setting

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Pin Assignments

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
DIO Test Wiring:
1. Use CA-2002 (optional) to connect the CON1 with CON2.
Analog Input Test Wiring:
2. Prepare for device:
DN-37 (optional) Wiring terminal board.
Provide a stable signal source. (For example, dry battery)
3. Connect a DN-37 to the CON3.
Self-Test
CA-2002
CON2
CON1
CON3
CA-3710

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
4. Wire the signal source to channel 0, and then keep set the JP1 jumper to
Single-Ended (page 3), and wire the signals as follows:
Connect the AI 0 (Pin01) to signal positive (+)
Connect the A.GND (Pin17) to signal negative (-)
5. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be placed in the default path after completing installation.
The UniDAQ Utility.exe is located in (Default path): C:\ICPDAS\UniDAQ\Driver\
Click this button
to start test.
3
Confirm the PCI-1002 series card
had successfully installed to PC. It
starts from 0.
2
Double-Click
1

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
6. Get DIO function test result.
Select the “Port 0”
8
The corresponding D/I becomes red for
channel 0, 2, 4, 6 of D/O is ON.
9
Click “Digital Input”item.
7
Select the “Port 0”.
Check channel 0, 2, 4, 6
6
5
Click “Digital Output” item.
4
PASS

PCI-1002, PEX-1002 L/H Series Quick Start Guide ICP DAS CO., LTD.
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
7. Get A/D function test result.
PCI-1002/PEX-1002 Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pci-1002.html
DN-37, CA-3710 and CA-2002 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information
Click this button to start test.
12
Check analog input on Channel 0 textbox.
The other channels value for floating
number.
13
Confirm the configuration setting.
11
PASS
Click “Analog Input”item.
10