ICP DAS USA PISO-P16R16U User manual

PISO-P16R16U and PEX-P8R8i/P16R16i Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icpd[email protected]
The package includes the following items:
One PISO-P16R16U series board as follows:
-
PISO-P16R16U
PEX-P8R8i
PEX-P16R16i
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
-
One CA-4037B Cable
One CA-4002 D-Sub connector
Two CA-4002 D-Sub connectors
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
For PISO-P16R16U
PEX-P8R8i/P16R16i
What’s in the shipping package?
English/ Jun. 2013/ Version 1.0
Installing Windows Driver

PISO-P16R16U and PEX-P8R8i/P16R16i Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icpd[email protected]
The PISO-DIO Series classic driver supports Windows 98/NT/2K and 32-bit
XP/ 2003/ Vista/7/8. Recommended to install this driver for have been
used PISO-P16R16U series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/quickstar
t/classic/
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Jumper Setting
1. CN1: D/I/O channel 0-7.
2. CN2: D/I/O channel 8-15.
3. JP1-JP8: AC Filter Jumpers
4. JP9-JP16: AC Filter Jumpers
5. SW1: Card ID Setting.
6. PCI Bus: for PISO-P16R16U
PCI Express: for PEX-P8R8i/P16R16i
1
2
3
4
5
6

PISO-P16R16U and PEX-P8R8i/P16R16i Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icpd[email protected]
Please make sure jumper is kept in default setting before self-test.
Input Signal Type Jumper
For more detailed jumper and SW1 information, please refer to section 2.2
Jumper and Card ID Switch Settings of the user manual.
(CD:\NAPDOS\PCI\PISO-DIO\manual\)
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI/PCI Express slot.
Step 4: Carefully insert your I/O card into the PCI/PCI Express slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
Installing Hardware on PC
JP1~JP8 and JP9~JP16
Jumper
Channel
Jumper
Channel
JP1
DI 0
JP9
DI 8
JP2
DI 1
JP10
DI 9
JP3
DI 2
JP11
DI 10
JP4
DI 3
JP12
DI 11
JP5
DI 4
JP13
DI 12
JP6
DI 5
JP14
DI 13
JP7
DI 6
JP15
DI 14
JP8
DI 7
JP16
DI 15
Without Filter for
DC Signal
(Default)
Without AC Filter for
AC Signal

PISO-P16R16U and PEX-P8R8i/P16R16i Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icpd[email protected]
Pin Assignments
Extension Cable (CA-4037B):
DB-40-Pin conversion DB-37-Pin

PISO-P16R16U and PEX-P8R8i/P16R16i Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icpd[email protected]
Prepare for device:
DN-37 (optional) wiring terminal board.
Exterior power supply device. For example: DP-665 (optional)
Self-test wiring as follows:
1. Use the DN-37 to connect the CON1 on board.
2. Connect the COM(0-7) with DIA(0-7).
(Pin2/5/8/21/24/26/28/11 connects to Pin12/13/14/15/16/17/18/19).
3. Power Supply GND connects to DIB0…DIB7 (Pin30/31/32/33/34/35/36/37).
Power Supply GND connects to GND (Pin29).
4. Power Supply (+24 V) connects to NO(0-7) (Pin1/4/7/20/23/25/27/10).
Self-Test

PISO-P16R16U and PEX-P8R8i/P16R16i Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icpd[email protected]
4. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be
placed in the default path after
completing installation.
The UniDAQ Utility.exe is located in:
C:\ICPDAS\UniDAQ\Driver\
(Default path).
5. Get DIO function test result.
Double-Click
1
Select the “Port 0”
Check channel 0, 2, 4, 6
6
5
Confirm the PISO-P16R16
series card had successfully
installed to PC. It starts from 0.
2
Click this button
to start test.
3
Click “Digital Output” item.
4

PISO-P16R16U and PEX-P8R8i/P16R16i Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , service.icpd[email protected]
PISO-P16R16U and PEX-P8R8i/P16R16i Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-p16r16u.html
DN-37, CA-3710 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Select the “Port 0”
8
The corresponding D/I becomes black for
channel 0, 2, 4, 6 of D/O is ON.
9
Click “Digital Input”item.
7
Related Information
PASS