ICP DAS USA PISO-730A Series User manual

Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [e-mail] Page: 1
Q
Qu ui ic ck k S St ta ar rt t
English/ Mar 2017/ Version 1.0
f
fo or r P PI IS SO O/ /P PE EX X- -7 73 30 0A A S Se er ri ie es s
Shipping Package
The package includes the following items:
PISO/PEX-730A Series Card x1 Quick Start (This Document) x1 Software CD x1
CA-4002 D-Sub Connectorx1
1
1
1
配置圖
2
2
2
1. CON1: Isolated DIO channel 0-15.
2. CON2: 5V/TTL DI channel 0-15.
3. CON3: 5V/TTL DO channel 0-15.
4. SW1: Card ID Setting for PEX-730A
5. PCI Bus: for PISO-730A/PISO-730A-5V
PCI Express: forPEX-730A
※ For more detailed SW1 information,
please refer to manual Section 2.4 Card ID
Switch Settings.
(CD:\NAPDOS\PCI\PISO-DIO\manual\)
PCI
controller
DI
DO
SW1
ON





PISO-730A
PISO-730A-5V
PEX-730A

Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om Page: 2
I In ns st ta al ll li in ng g w wi in nd do ow ws s D Dr ri iv ve er r
Setup the Windows driver, which can be obtained from either the companion CD-ROM or the ICP
DAS web site:

The UniDAQ driver supports 32-/64-bit Windows XP/2003/7/8/10; it is recommended to
install this driver for new user.
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/

The PISO-DIO series classic driver supports Windows 98/NT/2K and 32-bit XP/
2003/7/8/10. Recommended to install this driver for have been used PISO-730A series
boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/piso-dio/manual/quickstart/classi
c/
Click the “Next>”button to start the installation.
Check your I/O Card is or not on supported list, then click the “Next>”button.
Select the installed folder, the default path is C:\ICPDAS\UniDAQ , confirm and click the “Next>”
button.
Check your I/O Card on list, then click the “Next>”button.
Click the “Next>”button on the Select Additional Tasks window.
Click the “Next>”button on the Download Information window.
Select “No, I will restart my computer later”and then click the “Finish”button.
For more detailed information about how to install the UniDAQ driver, refer to “Section 2.2 Install
UniDAQ Driver DLL”of the UniDAQ Software Manual, which can be found in the
\NAPDOS\PCI\UniDAQ\Manual\ folder on the companion CD, or can be downloaded from:
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/manual/
3
3
3

Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om Page: 3
I
In ns st ta al ll li in ng g H Ha ar rd dw wa ar re e o on n P PC C
Shut down and power off your computer.
Remove the cover from the computer.
Select an unused PCI/PCI Express slot.
Carefully insert your I/O card into the PCI/PCI Express slot.
Replace the PC cover.
Power on the computer.
Follow the prompt message to finish the Plug & Play steps.
Please open the “Device Manager” to verify the I/O card is
correctly listed in the Device Manager.
4
4
4
Installation successful

Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om Page: 4
P
Pi in n A As ss si ig gn nm me en nt ts s
5
5
5

Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om Page: 5
S Se el lf f- -T Te es st t
Prepare for device:
DN-37 (optional) wiring terminal board
Exterior power supply device. For example: DP-665 (optional)
CA-3710 (optional) cable and CA-2002 (optional) cable
Self-test wiring as follows:
Use CA-2002 to connect the CON2 with CON3 on board.
Use the DN-37 to connect the CON1 on board.
Connect the CON1.IDI (0-15) with CON1.IDO (0-15).
(Pin1 connects to Pin11 … … Pin27 connects to Pin37)
PISO-730A/PEX-730A External Power +9 V ~ +30 V Wiring:
External Power +24 V connect to EO.COM1 (Pin10) and EO.COM2 (Pin19).
External Power GND connect to EI.COM1 (Pin9) , EI.COM2 (Pin28) and IGND (pin29).
DN-37 I/O Wiring
+24V
GND
GND
+5V
1 3 4 5 6 7 8 910 11 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
122
CON1
CON2
CON3
External
DP-665
CA-3710
CA-2002
6
6
6

Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om Page: 6
PISO-730A-5V External Power +5 V ~ +12 V Wiring:
External Power +5 V connect to EO.COM1 (Pin10) and EO.COM2 (Pin19).
External Power GND connect to EI.COM1 (Pin9) , EI.COM2 (Pin28) and IGND (pin29).
DN-37 I/O Wiring
+24V
GND
GND
+5V
1 3 4 5 6 7 8 910 11 13 14 15 16 17 18 19
20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
122
CON1
CON2
CON3
External
DP-665
CA-3710
CA-2002
Execute the UniDAQ Utility as follows:
In Windows 7, click the “Start” button, point to
“All Programs”,and then click the “ICPDAS”folder.
Point to “UniDAQ Development Kits”and then click
the “UniDAQ Utility”to execute the UniDAQ Utility
Program.

Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om Page: 7
Confirm that PISO-730 Series card has been
successfully installed in the host system. Note that the
device numbers start from 0.
Click the “TEST”button to start the test.
Check the results of the Digital Input/Output functions test.
1. Click the “Digital Output”tab.
2. Select “Port0”from the “Port Number”drop-down menu.
Note: Port0/1 is isolated digital input/output (IDI/IDO), Port2/3 is non-isolated digital
input/output (DI/DO).
3. Check the checkboxes for channels 0, 2, 4 and 6.




Copyright © 2017 ICP DAS Co., Ltd. All Rights Reserved. E-mail: [email protected]om Page: 8
4. Click the “Digital Input”tab.
5. Select “Port0”from the “Port Number”drop-down menu.
6. The DI indicators will turn black when the corresponding DO channels 0, 2, 4 and 6 are
ON. Note: Port0/1 IDI is the reverse logic, so the red light means low status (Logic 0)
and the black light means high status (Logic 1).
R
Re el la at te ed d I In nf fo or rm ma at ti io on n
PISO/PEX-730A series card product page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/piso-730a.html
DN-37, CA-3710, CA-2002 and DP-665 page (optional):
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
http://www.icpdas.com/products/Accessories/power_supply/dp-665.htm
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/



PASS
7
7
7