ICP DAS USA PISO-DA4U User manual

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
1
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The package includes the following items:
One PEX-DA, PISO-DAxU and PIO-DAxU series board as follows:
PEX-DA series: PEX-DA4, PEX-DA8, PEX-DA16
PISO-DAxU series: PISO-DA4U, PISO-DA8U, PISO-DA16U
PIO-DAxU series: PIO-DA4U, PIO-DA8U, PIO-DA16U
One Software Utility CD (V5.2 or later)
One Quick Start Guide (This Document)
One CA-4002 D-Sub connector
Step 1: Setup the Windows driver. The driver is located at:
The UniDAQ driver supports 32-/64-bit Windows 2K/XP/2003/Vista/7/8; it
is recommended to install this driver for new user:
CD: \NAPDOS\PCI\UniDAQ\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/dll/driver/
For PEX-DA4/8/16
PISO-DA4U/8U/16U
PIO-DA4U/8U/16U
What’s in the shipping package?
Installing Windows Driver
English/ Oct. 2013/ Version 1.1

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
2
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
The PIO-DA driver supports Windows 98/NT/2K and 32-bit XP/ 2003/
Vista/7/8. Recommended to install this driver for have been used PIO-DA
series boards of regular user, please refer to :
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-da/manual/quickstart/
classic/
Step 2: Click the “Next>”button to start the installation.
Step 3: Check your DAQ Card is or not on supported list, then click the
“Next>”button.
Step 4: Select the installed folder, the default path is C:\ICPDAS\UniDAQ ,
confirm and click the “Next>”button.
Step 5: Check your DAQ Card on list, then click the “Next>”button.
Step 6: Click the “Next>”button on the Select Additional Tasks window.
Step 7: Click the “Next>”button on the Download Information window.
Step 8: Select “No, I will restart my computer later”and then click the
“Finish”button.
For detailed information about the driver installation, please refer to Chapter
2.1 “Getting the UniDAQ Driver DLL Installer package”of the UniDAQ SDK
user manual.
Step 1: Shut down and power off your computer.
Step 2: Remove the cover from the computer.
Step 3: Select an unused PCI/PCI Express slot.
Step 4: Carefully insert your I/O card into the PCI/PCI Express slot.
Step 5: Replace the PC cover.
Step 6: Power on the computer.
After powering-on the computer, please finish the Plug&Play steps according
to the prompted messages.
Installing Hardware on PC

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
3
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
Pin Assignments

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
4
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
DIO Test Wiring:
1. Use the CA-2002 (optional) to connect the CON1 with CON2.
Analog Output Test Wiring:
2. Prepare for device:
DN-37 (optional) Wiring terminal board.
Digital Multi-Meter.
3. Connect a DN-37 to the CON3.
Self-Test
CA-2002
CON1
CON2
CON3

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
5
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
4. Connect the positive probe (+) of Multi-meter to VO_0 (Pin 0), and then
the negative probe (-) of Multi-meter to A.GND (Pin 05).
5. Execute the UniDAQ Utility Program.
This program (UniDAQ Utility) will be
placed in the default path after
completing installation.
Default Path:
C:\ICPDAS\UniDAQ\Driver\
Double-Click
1
Confirm the PIO-DA
series card had
successfully installed to
PC. It start s from 0.
2
Click this button
to start test.
3

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
6
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
6. Get DIO function test result.
Select the “Port 0”
Check channel 0, 2, 4, 6
6
5
Click “Digital Output” item.
4
Select the “Port 0”
8
The corresponding D/I becomes red
for channel 0, 2, 4, 6 of D/O is ON.
9
Click “Digital Input”item.
7
PASS

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
7
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
7. Get Analog Output function test result.
Select the “Port 0”
Select the “+/- 10V”
11
Click “Analog Output”item.
10
Type the voltage value
12
13
Click this button.
14
PASS
4.995
Check the value on multi-meter,
they should be identical to the values
set in program.
The value read on meter may be a little difference from the DA value because of the
resolution limit of meter or the measurement error.
15

PEX-DAx/PIO-DAxU/PISO-DAxU Quick Start Guide ICP DAS CO., LTD.
8
WebSite: http:// www.icpdas.com.tw E-Mail: [e-mail] , [e-mail]
PEX-DAx, PIO-DAxU and PISO-DAxU Series Card Product Page:
http://www.icpdas.com/root/product/solutions/pc_based_io_board/pci/pio-da4.html
CA-2002, CA-3710 and DN-37 page (optional):
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
Documentation and Software:
CD:\NAPDOS\PCI\UniDAQ\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/unidaq/
Related Information