IDEAL 7000TLX Supplement

Aug 2021
‘Low Rise / Portable / Storable’
Automotive Tilt Lift
7,000 lb. Capacity
Assembly & Operation Manual
IMPORTANT NOTICE !!
FOR USE WITH UNIBODY CONSTRUCTED VEHICLES ONLY
(FRAME CHASSIS MAX WIDTH OF 61”& MIN WIDTH OF 48”)

2
TLX-7000
Aug 2021
TABLE OF CONTENTS
SAFETY INFORMATION
·Note, Caution and Warning
·Important Information
·Safety Instructions
TECHNICAL INFORMATION
·Product Description
·Specifications
BEFORE USING
·Site Selection
·Surface Condition
·Operating Conditions
INSTALLATION INSTRUCTIONS
·Required Tools
·Shipping Crate
·Package Contents
·Tilt Lift Assembly
·Tilt Lift Preparation (Lowering)
FINAL PREPARATION & POSITIONING
·Jack Stand Preparation
·Positioning Tilt Lift Under Vehicle
·Basic Vehicle Layout Positions
OPERATION INSTRUCTIONS
·To Raise Vehicle
·To Lower Vehicle
·To Tilt Vehicle
·Tilt Lift Storage
·Manual Handle & Adapter
INSPECTION, MAINTENANCE & CLEANING
·Before Each Use
·Daily
·Monthly
EXPLODED VIEWS & PARTS LIST
LIMITED WARRANTY

3
TLX-7000
Aug 2021
SAFETY INFORMATION
Note, Caution and Warning
This document uses the following notations: Note, Caution and Warning –to alert you to special instructions,
tips, or hazards for a given procedure. Please familiarize yourself with the notation explanations described
below.
Indicates important information that requires special attention, such as a procedure for a
specific vehicle, or tips on operating the equipment.
Indicates the potential for damage to equipment, accessories, or the vehicle unless the
instructions or procedure are followed specifically.
Indicates the potential for property damage, personal injury, or death due to hazards
associated with the equipment, vehicle, or environment. Do not perform any procedures
until you have read and understood the warning instructions.
Important Information
1. Read this manual thoroughly before installing, operating, or maintaining the lift.
2. This lift is rated to 7,000-lbs lifting capacity. NEVER EXCEED rated lifting capacity of lift.
3. This lift is designed for indoor & outdoor use and should not be installed in a pit or depression.
4. The floor/surface on which the lift is to be used should be smooth and flat as possible.
5. The lift has specific mechanical requirements as described in the Installation Instructions section of
this manual.
6. This lift has a minimum vehicle height requirement as described in the Installation Instructions
section of this manual.
7. Failure by the owner / operator to provide the power drill requirements, proper surface, and
recommended shelter (when not in use) could result in unsatisfactory lift performance, property
damage, or personal injury.
8. Do not attempt to install / assemble this lift if you have never been trained on basic automotive lift
installation procedures.
9. Stay clear of any moving parts that cause injury.
10.The operation of the lift is permitted by authorized persons only.

4
TLX-7000
Aug 2021
Safety Instructions
1. Only trained personnel should operate this lift. All non-trained personnel should be kept away from
work area. Never let non-trained personnel come in contact with or operate lift.
2. Do not raise a vehicle on the lift until the installation is completed as described in this manual.
3. Technicians should be trained to use and care for the lift by familiarizing themselves with the
manual, including Note, Caution and Warning information. The lift should never be operated by an
untrained person.
4. Do not overload the lift. The capacity of the lift is shown on cover of this manual and on the lift’s serial
number tag.
5. Keep everyone clear of the lift when the lift is moving, the locking mechanism is disengaged or if
the vehicle is in danger of falling.
6. Unauthorized personnel should never be in the shop area when the lift is in use.
7. Inspect the lift daily. The lift should never be operated if it has damaged components or is
malfunctioning. Replace damaged components with manufacturer’s parts, or equivalent.
8. Keep area around lift clear of obstacles and well lighted.
9. To reduce the risk of personal injury, keep hair, loose clothing, fingers, and all body parts away from
moving parts.
10. To reduce the risk of electric shock, do not operate the lift when wet, do not expose the lift to rain.
11. Use the lift only as described in this manual, use only manufacturer’s recommended attachments.
12. Anyone who will be in the vicinity of the lift when it is in use should familiarize themselves with
any Caution, Warning, and Safety related decals supplied with this lift, and replace them if they are
illegible or missing.
13. Always ensure that the safety support jack is in place before any attempt is made to work on or
work near the vehicle, after being lifted & tilted.
14. Always wear safety glasses. Everyday eyeglasses may only have impact resistant lenses, and not
impact resistant frames. These are not safety glasses.
15. Maintain with care. Keep lift clean for proper & safe performance. Follow manual for proper
lubrication and maintenance instructions.
16. Check for damaged parts. Check lift & stand for proper alignment of moving parts, breakage of parts
or any condition that may affect the lift’s operation. Do not use lift if any component is broken or
damaged.
17. Never remove safety related components from the lift. Do not use lift if safety related components
are damaged or missing.

5
TLX-7000
Aug 2021
TECHNICAL INFORMATION
Product Description
The iDEAL 7000TLX (TLX-7000) is a low-profile, lightweight, portable 7,000 lb. capacity low-rise
scissor frame contact tilt lift. Equipped with twin dual-action precision gear drive mechanisms & dual
independent safety lock bar devices, the lifting operation is simply powered by the torque supplied
from an electric handheld drill. The exclusive twin dual-action gear drives & independent safety lock
bars also allow for full operation from either side of the lift. The unique and easy-to-use vehicle ‘lift &
tilt’operation provides greater overall accessibility to vehicle, while also being able to quickly &
conveniently be stowed out of the way. The iDEAL 7000TLX consists of a tilt lift assembly, jack stand,
platform risers, drill drive adapters, safety lock pins, wall mount storage brackets & manual handle
with socket adapter. Optional Floor Rail Kit also available.
Specifications
Specifications TLX-7000
Lift Capacity: 7,000 lbs.
Overall Length 51-3/4”
Overall Width 64-3/8”
Min. Height 4-1/2”
Max Lift Height 22-1/2”or 23-1/2”w/ Risers
Lift Speed *30 to 40 sec.
Lift Weight 111 lbs.
Platform Length & Width 31-1/2”x 7-1/4”
Min / Max Width - Outside Platforms 59-1/4”- 63-3/4”
Min / Max Width - Inside Platforms 44-1/2”- 49-1/4”
Power (Supplied By Customer / Operator) 10Amp - 120VAC 1/2”Corded Drill**
Ship Weight 214 lbs.
* Depending on Power Drill Amperage & Vehicle Weight.
** Cordless Drills Not Recommended
& Impact
or Pneumatic
Drills
Should
Not
Be Used
!
BEFORE USING
Site Selection
·LIFT LOCATION: Check layout dimension against floor plan requirements making sure that adequate
workspace is available. The floor surface on which the lift is to be used should be smooth and flat as
possible.
·OVERHEAD OBSTRUCTIONS: The area where the lift will be located should be free of overhead
obstructions such as heaters, building supports, electrical lines etc.
Surface Condition
·Do not use the Lift on any type of asphalt or soft surface. Ensure lift is placed on a dry, oil & grease
free, level concrete surface capable of supporting the weight of the Lift with a vehicle. Do not use Lift
on concrete expansion seams or cracked, defective concrete. Failure to accomplish the foundation
surface requirements may cause lift instability, which could result in personal injury.
Operating Conditions
·Operate lift only between temperatures of 41° - 104° F

6
TLX-7000
Aug 2021
INSTALLATION INSTRUCTIONS
These instructions must be followed to ensure proper installation and operation of your lift.
Failure to comply with these instructions can result in serious bodily harm and void product
warranty. Manufacturer will assume no liability for loss or damage of any kind, expressed or
implied resulting from improper installation or use of this product.
Required Tools
·Scissors
·Hammer or Small Crowbar
·30mm Open-End Wrench
·30mm Socket Wrench
·10 Amp* 120VAC 1/2”Corded Drill - DO NOT Use Impact Drill !!
(*Less than 10 Amps may cause difficulty raising larger & heavier vehicles)
Shipping Crate weight is approximately 215 lbs. Careful attention should be taken for offloading
& maneuvering Crate. The 66.3”L x 34.8”W x 10.4”H Crate is designed for easy mobility with
forklift or pallet jack.
Shipping Crate
1. Inspect shipping crate for any damages.
2. Open shipping crate by first cutting banding,
followed by carefully prying lid open.
3. Carefully remove all contents from crate, using
Package Contents list & diagram below to ensure
all items are included.
Package Contents
H
.
A.
Tilt Lift Frame Assembly (1)
B. Platform (2)
C. Platform Hardware:
·Pivot Bar (2)
·Spacer (4)
·Flat Washer (4)
·Nylon Nut (4)
D. Platform Riser Bar (2)
E. Drill Drive Adapter (4)
F. Safety Lock Pin (2)
G. Handle & Socket Adapter (1)
H. Wall Storage Bracket (2)
I.
Jack Stand
For Convenience
The iDEAL 7000TLX Tilt Lift comes
almost fully assembled.
Only the Platform Assemblies need
to be mounted to the Tilt Lift Frame.
(See Assembly
Info
Next)
A.
B
.
C
.
D
.
E
.
G
.
F
.
I
.

7
TLX-7000
Aug 2021
Tilt Lift Assembly
1. Raise Frame Arms up so both pivot holes align to each other. Locate Pivot Bars, Flat Washers,
Spacers & Nylon Nuts to mount Platforms. (Slightly coat interior of pivot holes with lithium grease.)
2. Insert Pivot Bar into Frame Arm holes. Apply Flat Washers to each side, as shown below.
3. Bias Pivot Bar to outside & slightly tilt Platform down to insert Bar thru the outer hole (A); then level
to inner Platform hole (B) to fully insert Pivot Bar. Insert Spacers to each side, as shown below.
A.
B
.

8
TLX-7000
Aug 2021
4. Ensure Platform, Pivot Pin, Washers & Spacers are properly installed to Tilt Lift Frame, as shown
below. Once confirmed, apply Nylon Nuts to each end of Pivot Pin to secure Platform assembly to
Lift Frame, using 30mm wrench & socket. Duplicate assembly steps 1-4 for opposite Platform.
Tilt Lift Preparation (Lowering)
1. Insert Drive Adapter into Power Drill and insert into either Gear Box. Note Direction to lower DOWN.
After tightening
Nylon Nuts to Pin.
Test that Platform
pivots & slides
side-to-side freely.
(Note: Drill’s ‘Forward or Reverse’to Lower Lift from either side. Manual Handle can also be used to Lower.)
Manual Handle
& Adapter

9
TLX-7000
Aug 2021
2. Based on which Gear Box is being used, gently apply power to drill to confirm the correct rotation of
drill to lower lift DOWN. Once confirmed, slowly begin applying power to drill to fully lower Lift.
3. Once Lift has been lowered, it’s now configured to roll on Casters to easily position under vehicle.
You may see some grease on sides of drive shafts as lift raises & lowers. This is normal
and the amount of grease will reduce with use.
This Completes the iDEAL 7000TLX Tilt Lift Assembly.

10
TLX-7000
Aug 2021
FINAL PREPARATION & POSITIONING
Jack Stand Preparation
1. Position Jack Stand in vertical position.
2. Fully unfold legs of Jack Stand for proper stability.
3. Remove Pin to adjust to Pillar & Pad to desired height.
Positioning Tilt Lift Under Vehicle
1. Ensure vehicle is positioned on a dry, oil & grease free, level concrete surface capable of
supporting the weight of the Lift with a vehicle
2. Before using Tilt Lift, always put vehicle in Park and set Emergency Brake.
3. Position the Tilt Lift under vehicle closest to front wheels by rolling the Lift under vehicle.
4. Adjust Platforms to chassis frame rails. If pinch welds or body molding interferes with Platform
surface, place Riser Bars on Platforms before raising vehicle.
5. Double check for proper clearances between Platforms and chassis frame rails prior to lifting
vehicle.
Basic Vehicle Layout Positions
A. Front Engine / Front Wheel Drive - recommended to position iDEAL Tilt Lift under vehicle so that the
gear boxes are positioned about 4”behind the front wheels.
B. Front Engine / Rear Wheel Drive - recommended to position the iDEAL Tilt Lift under vehicle so that
the gear boxes are positioned about 12”behind the front wheels.
C. Rear Engine / Rear Wheel Drive - recommended to position the iDEAL Tilt Lift under vehicle with gear
boxes facing towards rear wheels so that the gear boxes are positioned about 4”from the back wheels.
Recommendations noted above should be used as a ‘base-line’for the iDEAL Tilt Lift
placement. You may need to adjust the lift’s position ‘front or back’an inch or two in order
to obtain easy vehicle tilting. Once the best balance placement for the lift & vehicle has
been established, it is recommended to mark the underside of vehicle for future usage.
For Use Only with Unibody Constructed Vehicles with Maximum Chassis Width of 61”&
Minimum Chassis Width of 48”. Failure may result in Vehicle and/or Lift Damage.

11
TLX-7000
Aug 2021
OPERATION INSTRUCTIONS
To Raise Vehicle:
·Place vehicle in PARK and set Parking Brake.
·Use on hard level surfaces only, keeping area clear around vehicle.
·Measure the width between chassis frame rails for correct Platform location.
·Roll lift under vehicle with the Drive Gearbox, typically closest to front wheels.
·Position lift Platforms under both the driver’s & passenger’s side of the vehicle’s frame. If necessary,
adjust Platforms side-to-side for proper alignment to chassis frame.
Vehicles with pinch welds may require Platform Riser Bars for proper clearances to avoid
causing damage to vehicle or lift.
·Insert Drill Adapter into drill and tighten.
·Select which side of Tilt Lift & vehicle will be best to work from. (See NOTE Info. below)
The iDEAL 7000TLX is equipped with twin dual-action gear drives & dual independent
safety lock bars & safety pins. The twin dual-action gear drives & dual independent safety
lock bars allow for full operation from either side, using the ‘forward & reverse’function of
the power drill.
For single direction drills, lift operation can still be easily utilized by using the side-specific
gearbox for ‘Up & Down’lift operations, as indicated on the Gearbox decal plates.
·Connect power to Drill, double checking drill’s rotation, prior to inserting Adapter into Gearbox Socket.
Before raising vehicle, verify that there is enough overhead clearance for vehicle once
raised & tilted.
·Raise lift until lift Platforms contact the chassis frame of the vehicle. If Platforms are not lining up
properly, lower lift slightly and readjust Platforms.
·Once lift is reset and Platforms are properly adjusted, raise lift to desired height. Lifting slowly.
As you raise the vehicle, typically the front half of the vehicle will begin to drop as the rear
of vehicle raises.
·Once lift is at desired height and one set of wheels are touching the ground, insert Safety Locking Pin
into one of the Safety Lock Bars.
Always Insert Safety Lock Pin, after vehicle has been raised to the desired height.
·Position Jack Stand under raised side of the vehicle. Adjust the Pillar height to support a solid section
of vehicle chassis, followed by inserting pin into hole to lock Pillar into position. Ensure Jack Stand is
placed on solid surface able to support vehicle.

12
TLX-7000
Aug 2021
To Lower Vehicle:
·Ensure area around & under the lifted / tilted vehicle is clear of any obstructions that may interfere with
vehicle coming down.
·Carefully, remove Jack Stand from under vehicle. Ensure to locate Stand clear of vehicle & lift.
·Remove Safety Locking Pin. Insert into storage position on lift.
·Insert Drill Adapter into the Gearbox Socket, using the ‘forward & reverse’function of power drill to
lower lift. Double check rotation of drill to lower lift, as noted on UP & DOWN arrows for each Gearbox.
·Slowly lower vehicle until all four wheels are touching the ground and the lift Platforms are clear of the
vehicle frame.
·Once lift is completely lowered, roll lift out from under vehicle and store for later use.
Never Drive Over Tilt Lift!! Damage to Vehicle and Tilt Lift Will Occur!
To Tilt Vehicle:
·Vehicles come in different sizes, configurations, engine locations & weights. Refer to the Basic
Vehicle Layout Positions, noted on page 10.
You may need to adjust the lift’s position ‘front or back’an inch or two in order to obtain
easy vehicle tilting. Once the best balance placement for the lift & vehicle has been
established, it is recommended to mark the underside of vehicle for future usage.
·In order to tilt the vehicle, carefully lift vehicle from the lowered end that has wheels touching the
ground.
Never Pull Down from the Vehicle End that is Raised. Damages to Vehicle may Occur.
·Ensure to lift to tilt vehicle from a solid part of the of the vehicle, like the fender, bumper, frame, etc.
Never Lift & Tilt Vehicle from Fragile Decorative type Parts of Vehicle.
·Once the vehicle starts to rise & tilt, control rise by using two hands to control vehicle transitioning onto
the opposite wheels. Try not to let the vehicle bounce, as damages may occur.
·Always position Jack Stand under the tilted vehicle to ensure vehicle will not unexpectedly tilt back or
down while working on vehicle.
When raising, lowering and especially tilting vehicle, ensure there is enough room under
the bumpers, so damages will not occur.

13
TLX-7000
Aug 2021
Tilt Lift Storage
·The iDEAL 7000TLX comes standard with Wall Storage Brackets.
Brackets are designed to support full weight of the Tilt Lift.
·Mounting hardware is purposely not included, allowing the customer
the ability to choose the type of wall anchoring hardware that is best
for their wall mounting application. Wall Bracket holes allow for 1/4”
mounting hardware.
·Wall Bracket spacing should be positioned to the inside section of
tubular lift frame, as shown below. The Tilt Lift can also be carefully leaned against wall.
·Carefully raise Tilt Lift to an upright position, with Gear Boxes on top. Lift & position Tilt Lift onto Wall
Brackets so that the lift is supported by the tubular lift frame between the gear boxes, circled below.
Manual Handle & Adapter
·The Manual Handle & Socket Adapter can conveniently be used in place of the Power Drill or in cases
of power outages and/or when power may not available.
INSPECTION, MAINTENANCE & CLEANING
Always unplug the Power Cord from the electrical outlet before performing any inspection,
adjustments, maintenance and/or cleaning.
BEFORE EACH USE: Inspect the general condition of the Drill, Lift & Jack Stand. Check for loose
screws, misalignment or binding of moving parts, broken parts, damaged electrical wiring, and any
other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the
problem identified and corrected before further use. Do Not Use Damaged Equipment.
DAILY: With compressed air or vacuum, remove all dirt and debris from the Lift. Also, use a mild
detergent or cleaner to remove oil and grease from the unit.
MONTHLY: While the factory has pre-greased the Gear Drive Boxes & Drive Screw Bars, we
recommend that you periodically check and add white lithium grease as required. Grease is designed
to reduce friction of the gears and screw drives internally.
The iDEAL 7000TLX conveniently has Grease Zerks applied to the top each Gearbox for
the ease to add grease, when required.
Depending on how often you use the Lift, you should check Gear Drive Box periodically to
ensure there is enough lubrication to keep friction, wear & tear to a minimum.
For iDEAL Technical Assistance, please call 877-558-9337.

14
TLX-7000
Aug 2021
EXPLODED VIEWS

15
TLX-7000
Aug 2021
PARTS LIST
ITEM Tux P/N M-REF P/N DESCRIPTION QTY
1 TLX-7000-001 SL03-01000-000 Outer Drive Bar Tube 1
2 TLX-7000-002 SL03-02000-000 Inner Scissor Frame 1
3 TLX-7000-003 SL03-03000-000 Outer Scissor Frame 1
4 TLX-7000-004 SL03-00013-000 Platform Pivot Bar 2
5 TLX-7000-005 SL03-05000-000 Inner Drive Bar Tube 2
6 TLX-7000-006 SL03-00014-000 Platform Spacer 4
7 TLX-7000-007 5301-00020-000 Flat Washer, D20 4
8 TLX-7000-008 5206-00020-000 Lock Nut, M20 4
9 TLX-7000-009 SL03-00009-000 Nylon Wheel 2
10 TLX-7000-010 SL03-00004-000 Wheel Pin, D12x66 2
11 TLX-7000-011 SL03-00015-000 Outer Lock Bar Pin, D12x88 2
11.1 TLX-7000-011.1 SL03-00024-000 Inner Lock Bar Pin, D12x71 2
12 TLX-7000-012 5404-03020-000 Cotter Pin, D3x20 12
13 TLX-7000-013 SL03-00003-000 Outer Lock Bar Tube 2
14 TLX-7000-014 SL03-00002-000 Inner Lock Bar Tube w/ Holes 2
15 TLX-7000-015 SL03-00016-000 Small Spacer 2
16 TLX-7000-016 5104-10035-001 Bolt, M10x35 2
17 TLX-7000-017 5104-08010-001 Bolt, M8x10 2
18 TLX-7000-018 SL03-00001-000 Half-Moon Collar Clamp 2
19 TLX-7000-019 SL03-00022-000 Safety Latch Pin 2
19.1 TLX-7000-019.1 SL03-25003-FJ6 Ring 2
20 TLX-7000-020 5110-05014-000 Screw, M5x14 8
20.1 TLX-7000-020.1 5107-05010-000 Screw, M5x10 8
21 TLX-7000-021 5206-00010-000 Lock Nut, M10 2
22 TLX-7000-022 5206-00005-000 Lock nut, M5 8
23 TLX-7000-023 SL03-08001-000 Threaded Drive Bar 2
24 TLX-7000-024 SL03-00012-000 Flat Key 4
25 TLX-7000-025 SJ05-HYZ00-000 Grease Zerk (Flush) 2
26 TLX-7000-026 SL03-00005-000 Gear Box Case 2
27 TLX-7000-027 SL03-06002-000 Linkage Bar (LH) 1
27.1 TLX-7000-027.1 SL03-06002-001 Linkage Bar (RH) 1
28 TLX-7000-028 SL03-00007-000 Linkage Coupler 1
29 TLX-7000-029 5112-05010-FH0 Threaded Pin, M5x10 3
30 TLX-7000-030 SL03-00018-000 Position Ring 2
31 TLX-7000-031 5401-04020-000 Round Pin, D4x20 2
32 TLX-7000-032 SL03-00020-000 Small Gear 2
33 TLX-7000-033 5312-22002-000 Circlips, D22x2 2
34 TLX-7000-034 5602-12010-000 Ball Bearing 4
35 TLX-7000-035 5908-12024-005 Oil Seal 2
36 TLX-7000-036 SL03-06001-000 Hex Socket, H13 2
37 TLX-7000-037 5602-15009-000 Push Bearing (Small) 2
38 TLX-7000-038 SL03-08002-000 Position Ring 2
39 TLX-7000-039 5602-30011-000 Push Bearing (Large) 2
40 TLX-7000-040 SL03-00019-000 Large Gear 2

16
TLX-7000
Aug 2021
41 TLX-7000-041 SL03-00021-000 Nut 2
42 TLX-7000-042 SL03-00006-000 Gear Box Cover 2
43 TLX-7000-043 SL03-21002-FJ2 Plastic Cap 4
44 TLX-7000-044 SL03-00011-000 Nylon Bushing 4
45 TLX-7000-045 SL03-07000-000 Linkage Support Tube 2
46 TLX-7000-046 5206-00008-000 Lock Nut, M8 2
47 TLX-7000-047 5206-00006-000 Lock Nut, M6 12
48 TLX-7000-048 5301-00006-000 Flat Washer, D6 12
49 TLX-7000-049 SL03-00023-000 Swivel Caster 3
50 TLX-7000-050 5110-06020-000 Screw, M6x20 12
51 TLX-7000-051 SL03-04000-000 Platform 2
52 TLX-7000-052 SL03-00008-000 Rubber Pad 2
53 TLX-7000-053 SL03-20100-FJ1 Riser Bar 2
53.1 TLX-7000-053.1 SL03-20001-FJ1 Rubber Bar Pad 4
54 TLX-7000-054 SL03-21100-FJ2 Hanger Bracket 1
54.1 TLX-7000-054.1 SL03-21001-FJ2 Rubber Pad 1
55 TLX-7000-055 SL03-10000-000 Drill Drive Adapter 4
56 TLX-7000-056 SL03-00017-000 Swivel Connector, H13 1
57 TLX-7000-057 SL03-09001-000 Hand Crank Bar 1
57.1 TLX-7000-057.1 SL03-09002-000 Pivot Handle 1
57.2 TLX-7000-057.2 5312-16016-000 Circlips, D16x1.6 4
59 TLX-7000-059 5301-00012-000 Flat Washer, D12 12
60 TLX-7000-060 5402-05020-000 Cotter Pin, D5x20 3
JACK STAND
58 TLX-7000-058 SL03-25000-FJ6 Jack Stand 1
58.1 TLX-7000-058.1 SL03-25300-FJ6 Outer Support Tube 1
58.2 TLX-7000-058.2 5206-00005-000 Lock Nut, M5 9
58.3 TLX-7000-058.3 SL03-00001-FJ6 Circle Frame 3
58.4 TLX-7000-058.4 SL03-25400-FJ6 Leg Pivot Bar 3
58.5 TLX-7000-058.5 5110-05040-000 Screw, M5x40 6
58.6 TLX-7000-058.6 SL03-25200-FJ6 Support Leg 3
58.7 TLX-7000-058.7 SL03-25100-FJ6 Inner Lock Tube & Pad 1
58.8 TLX-7000-058.8 SL03-24004-FJ6 Hitch Pin, D2 1
58.9 TLX-7000-058.9 SL03-25002-FJ6 Pin 1
58.10 TLX-7000-058.10 SL03-25003-FJ6 Ring 1
58.11 TLX-7000-058.11 SL03-25004-FJ6 Chain 1
58.12 TLX-7000-058.12 5110-05016-000 Screw, M5x16 3

17
TLX-7000
Aug 2021
LIMITED WARRANTY
Structural Warranty:
The following parts and structural components carry a five-year warranty:
Columns Arms Uprights Swivel Pins
Legs Carriages Overhead Beam
Tracks Cross Rails Top Rail Beam
Limited One-Year Warranty:
Tuxedo Distributors, LLC (iDEAL) offers a limited one-year warranty to the original purchaser of Lifts and Wheel Service
equipment in the United States and Canada. Tuxedo will replace, without charge, any part found defective in materials or
workmanship under normal use, for a period of one year after purchase. The purchaser is responsible for all shipping
charges. This warranty does not apply to equipment that has been improperly installed or altered or that has not been
operated or maintained according to specifications.
Other Limitations:
This warranty does not cover:
1. Parts needed for normal maintenance
2. Wear parts, including but not limited to cables, slider blocks, chains, rubber pads and pulleys
3. Replacement of lift and tire changer cylinders after the first 30 days. A seal kit and installation instructions will be
sent for repairs thereafter.
4. On-site labor
Upon receipt, the customer must visually inspect the equipment for any potential freight damage before signing clear on
the shipping receipt. Freight damage is not considered a warranty issue and therefore must be noted for any potential
recovery with the shipping company.
The customer is required to notify Tuxedo of any missing parts within 72 hours. Timely notification must be received to be
covered under warranty.
Tuxedo will replace any defective part under warranty at no charge as soon as such parts become available from the
manufacturer. No guarantee is given as to the immediate availability of replacement parts.
Tuxedo reserves the right to make improvements and/or design changes to its lifts without any obligation to previously
sold, assembled, or fabricated equipment.
There is no other express warranty on the Tuxedo lifts and this warranty is exclusive of and in lieu of all other warranties,
expressed or implied, including all warranties of merchantability and fitness for a particular purpose.
To the fullest extent allowed by law, Tuxedo shall not be liable for loss of use, cost of cover, lost profits, inconvenience,
lost time, commercial loss or other incidental or consequential damages.
This LimitedWarranty is granted to the original purchaser only and is not transferable or assignable.
Some states do not allow exclusion or limitation of consequential damages or how long an implied warranty lasts,
so the above limitations and exclusions may not apply. This warranty gives you specific legal rights and you may
have other rights, which may vary from state to state.
8320 E Hwy 67, Alvarado, TX 76009
Ph. 817-558-9337 / Fax [phone]