IEI Technology PM-US15W User manual

1
PCI-104 with Intel® Atom™ Z510/Z530 Processor, 18/24 bit LVDS,
LAN, USB, CF, 4 COM
PM-US15W
Quick Installation Guide
Version 1.1
June 11, 2010
Package Contents
PM-US15W package includes the following items:
z1 x PM-US15W Single Board Computer
z1 x IDE 44p/44p flat cable
z1 x Quad ports RS-232 cable
z2 x Dual USB ports cable
z1 x LAN cable
z1 x KB/MS cable
z1 x Power cable
z1 x Mini Jumper Pack
z1 x Utility CD
z1 x QIG (Quick Installation Guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
zCPU:
Intel® Atom™ Z530 1.6GHz Processor with a 533MHz FSB
(PM-US15W-Z530) with HT support
Intel® Atom™ Z510 1.1GHz Processor with a 400MHz FSB
(PM-US15W-Z510) without HT support
zSystem Chipset: Intel® SCH US15W
zBIOS: AMI BIOS
zSystem memory:
1 x 200-pins SO-DIMM DDR2 533/400MHz SDRAM (max. 2GB)
zEthernet: One Realtek RTL8102E 10/100Mbps Ethernet chipset
(PCIe Interface)
zI/O Interface:
4 x RS-232
1 x RS-422/485 (Shared with COM2)
4 x USB 2.0 (4 by pin-header)
1 x IDE
1 x PS/2 KB/MS by pin-header
1 x CF type Ⅱslot
zExpansions:
PCI/104 slot (PCI BUS by PCIe to PCI bridge: PLX PEX8112)
zDigital I/O: 8-bit digital I/O, 4-bit input/4-bit output by CPLD:
ALTERA EPM570T100
zDisplay Interface:
VGA support by LVDS to VGA Module (LVDS-VGA-R10)
18/24-bits Dual-Channel LVDS
zAudio:
HD audio Interface, audio support by IEI 7.1 channel HD Audio kit
with Realtek ALC883 codec supports dual audio streams
(AC-KIT883HD)
zWatchdog timer:
Software programmable supports 1~255 sec. system reset by
Super I/O SMSC SCH3114-NU
zPower Supply: +5V only, AT/ATX Mode support, 12V for LCD

3
Inverter
zPower Consumption:
[email protected] (Intel® Atom™ Z510 1.1GHz with 1GB DDR2 DRAM)
zHumidity: Operation: 5% ~ 95% , non-condensing
zTemperature: 0 ~ 60°C(32 ~ 140°F)
zDimension: 96 mm x 90 mm
zWeight: GW: 650g; NW: 250g
Ordering Information
PM-US15W-Z530-R11:PCI-104 with Intel® Atom™ Z530 Processor, 18/24
bit LVDS, LAN, USB, CF, 4 COM
PM-US15W-Z510-R11:PCI-104 with Intel® Atom™ Z510 Processor, 18/24
bit LVDS, LAN, USB, CF, 4 COM
LVDS-VGA-R10: LVDS to VGA converter board
AC-KIT883HD-R10:7.1 channel HD audio kit with Realtek ALC883 codec
support dual audio streams
ITS-44-R10: 2.5” IDE to SATA module
32200-074800-RS: RS-422/485 cable
Table of Jumper Setting
LABEL FUNCTION
JP2 LCD Panel Voltage select setting
JP4 COM2 RS-232/422/485 Select setting
SW1 CF Master/Slave select setting
JP2: LCD Panel Voltage select
JP2 Description
1-2 Panel Voltage 3.3V
(Default)
2-3 Panel Voltage 5V
JP4: COM2 RS-232/422/485 Select
(RS-232 on CN6 pin11~pin20, RS-422/485 on CN4)
JP4 Description
1-2 RS-232
(Default)
3-4 RS-422
5-6 RS-485
SW1: CF Master/Slave select
SW1 Description
Slave (1-2)
(Default)
Master (2-3)

4
Table of Connectors
LABEL FUNCTION
LAN1 LAN Connector
USB1 & USB2 Internal USB Connectors
CN8 Mainpower input connector (Terminal Block)
CN4 COM2 RS-422/485 Connector (COM2 RS-232
on CN6 pin11~pin20)
J1 LED indicating, Reset, power button, AT/AT
X
mode selection connector
BT1 Battery connector
KBMS Keyboard & Mouse Connector
LVDS1 LVDS LCD Interface Connector
CN5 LCD Inverter Connector
CN10 CF Card Interface Slot
DIO1 Digital I/O connector
CN6 COM1~COM4 Internal Serial Port Connecto
r
(COM2 RS-422/485 on CN4)
HDA-1 HD Audio Interface connector
CN1 IDE connector
CN3 CPLD Programming Connector
CN2 PCI/104 Connector (PCI Bus)
J2 DDR2 SO-DIMM socket
LAN1: LAN Connector
PIN DESCRIPTION PIN DESCRIPTION
1 VCC(+3.3V) 6 Active#
2 RX+ 7 RX-
3 Link# 8 GND
4 N/C 9 GND
5 TX+ 10 TX-
USB1 & USB2: Internal USB Connectors
PIN NO DESCRIPTION PIN NO DESCRIPTION
1 VCC(+5V) 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 VCC(+5V)

5
CN8: Mainpower input connector
(Terminal Block)
PIN Description
1+12V
2GND
3 +5V
CN4: COM2 RS-422/485 Connector
(COM2 RS-232 on CN6 pin11~pin20)
PIN Description
1RXD485#
2RXD485+
3TXD485+
4 TXD485#
J1: LED indicating, Reset, power
button, AT/ATX mode selection
connector
(9,10 short ATX mode, Jumper Default)
(9,10 open AT mode)
PIN DESCRIPTION
1 VCC(+5V) LED+
2 PWR
LED GND
3 VCC(+5V) LED+
4 HDD
LED HDD LED-
5 PWR BTN1
6 Power
button GND
7 RESET1
8 Reset
button GND
9 ATX_SEL#
10
AT/ATX
mode
select GND
BT1: Battery connector
PIN Description
1BATTERY(+3.3V)
2GND
KBMS: Keyboard & Mouse Connector
PIN DESCRIPTION
1 VCC(+5V)
2 MOUSE DATA
3 MOUSE CLOCK
4 KEYBOARD DATA
5 KEYBOARD CLOCK
6 GND
LVDS1: LVDS LCD Interface Connector
PIN NO. Description PIN NO. Description
2 GND 1 GND
4 AY0- 3 AY0+
6 AY1- 5 AY1+
8 AY2- 7 AY2+
10 AYCLK- 9 AYCLK+
12 AY3- 11 AY3+
14 GND 13 GND
16 NC 15 NC
18 LCDVCC 17 LCDVCC
20 LCDVCC 19 LCDVCC

6
CN5: LCD Inverter Connector
PIN NO. DESCRIPTION
1 LCD_BKLTCTL
2 GND
3 VCC(+12V)
4 GND
5 LCD_BKLEN
DIO1: Digital I/O connector
PIN Description PIN Description
1GND 2VCC(+5V)
3OUT0 4OUT1
5OUT2 6OUT3
7IN0 8IN1
9IN2 10 IN3
CN10 : CF Card Interface Slot
Pin No. Description Pin No. Description
1 GND 2 D3
3 D4 4 D5
5 D6 6 D7
7 CE# 8 GND
9 GND 10 GND
11 GND 12 GND
13 VCC (+5V) 14 GND
15 GND 16 GND
17 GND 18 A2
19 A1 20 A0
21 D0 22 D1
23 D2 24 NC
25 CD2# 26 CD1#
27 D11 28 D12
29 D13 30 D14
31 D15 32 CE2#
33 NC 34 IOR#
35 IOW# 36 WE#
37 IRQ 38 VCC(+5V)
39 CSEL# 40 NC
41 RESET# 42 WAIT#
43 INPACK# 44 REG#
45 BVD2 46 BVD1
47 D8 48 D9
49 D10 50 GND

7
CN6: COM1~COM4 Internal Serial Port Connector
COM1: RS-232(on Pin1~Pin10)
COM2: RS-232/422/485 (RS-232 on Pin11~Pin20,
RS-422/485 on CN4)
COM3: RS-232 (on Pin21~Pin30)
COM4: RS-232 (on Pin31~Pin40)
Pin Description Pin Description
1 DCD1# 2 DSR1#
3 RX1 4 RTS1#
5 TX1 6 CTS1#
7 DTR1# 8 RI1#
9 GND 10 GND
11 DCD2# 12 DSR2#
13 RX2 14 RTS2#
15 TX2 16 CTS2#
17 DTR2# 18 RI2#
19 GND 20 GND
21 DCD3# 22 DSR3#
23 RX3 24 RTS3#
25 TX3 26 CTS3#
27 DTR3# 28 RI3#
29 GND 30 GND
31 DCD4# 32 DSR4#
33 RX4 34 RTS4#
35 TX4 36 CTS4#
37 DTR4# 38 RI4#
39 GND 40 GND
HDA-1: HD Audio Interface connector
PIN Description PIN Description
1HAD_SYNC 2HAD_CLK
3HAD_SDO 4SCH_SPKR
5HAD_SDI0 6HAD_RST#
7+5V 8GND
9+12V 10 GND

8
CN1: IDE connector
Pin No. Description Pin No. Description
1 RESET# 2 GND
3 D7 4 D8
5 D6 6 D9
7 D5 8 D10
9 D4 10 D11
11 D3 12 D12
13 D2 14 D13
15 D1 16 D14
17 D0 18 D15
19 GND 20 NC
21 DRQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 RDY 28 NC
29 ACK# 30 GND
31 INT 32 NC
33 A1 34 CABLEID
35 A0 36 A2
37 CS0# 38 CS1#
39 ASP# 40 GND
41 +5V 42 +5V
43 GND 44 NC
CN3: CPLD Programming Connector
PIN NO. DESCRIPTION
1 VCC (+3.3V)
2 EPM_TMS
3 EPM_TDO
4 EPM_TCK
5 EPM_TDI
6 GND

9
CN2: PCI/104 Connector (PCI Bus)
Pin Description Pin Description Pin Description Pin Description
A1 GND B1 SERIRQ# C1 VCC5 D1 AD0
A2 VIO B2 AD2 C2 AD1 D2 VCC5
A3 AD5 B3 GND C3 AD4 D3 AD3
A4 BE0# B4 AD7 C4 GND D4 AD6
A5 GND B5 AD9 C5 AD8 D5 GND
A6 AD11 B6 VIO C6 AD10 D6 GND
A7 AD14 B7 AD13 C7 GND D7 AD12
A8 VCC3 B8 BE1# C8 AD15 D8 VCC3
A9 PULL 3V B9 GND C9 PULL 3V D9 PAR
A10 GND B10 PULL 3V C10 VCC3 D10 PULL 3V
A11 STOP# B11 VCC3 C11 PULL 3V D11 GND
A12 VCC3 B12 TRDY# C12 GND D12 DEVSEL#
A13 FRAME# B13 GND C13 IRDY# D13 VCC3
A14 GND B14 AD16 C14 VCC3 D14 BE2#
A15 AD18 B15 VCC3 C15 AD17 D15 GND
A16 AD21 B16 AD20 C16 GND D16 AD19
A17 VCC3 B17 AD23 C17 AD22 D17 VCC3
A18 IDSEL0 B18 GND C18 IDSEL1 D18 IDSEL2
A19 AD24 B19 BE3# C19 VIO D19 IDSEL3
A20 GND B20 AD26 C20 AD25 D20 GND
A21 AD29 B21 VCC5 C21 AD28 D21 AD27
A22 VCC5 B22 AD30 C22 GND D22 AD31
A23 REQ0 B23 GND C23 REQ1 D23 VIO
A24 GND B24 REQ2 C24 VCC5 D24 GNT0
A25 GNT1 B25 VIO C25 GNT2 D25 GND
A26 VCC5 B26 CLOCK0 C26 GND D26 CLOCK1
A27 CLOCK2 B27 VCC5 C27 CLOCK3 D27 GND
A28 GND B28 INTD# C28 VCC5 D28 RESET
A29 +12V B29 INTA# C29 INTB# D29 INTC#
A30 -12V B30 REQ4 C30 GNT4 D30 GND

10
Board Layout: Jumper and Connector Locations

11
Board with Heat Sink Dimensions: