IEI Technology iSignager-Frame-W07 User manual

iSignager Frame Series
Page i
IEI Technology Corp.
User Manual
iSignager Frame Series User Manual
7”/8”/10.2”/15.6” Digital Signage Display with
LAN, USB 2.0, VGA, Audio Output,
IP 64 compliant Front Panel and Remote Control
Rev. 1.01 – 21 December, 2009
MODEL:
iSignager Frame Series

iSignager Frame Series
Page ii
Revision
Date Version Changes
21 December, 2009 1.01 Modified power adapter information in Table 1-3.
20 October, 2009 1.00 Initial release

iSignager Frame Series
Page iii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

iSignager Frame Series
Page iv
Table of Contents
1 INTRODUCTION.......................................................................................................... 1
1.1 IMPORTANT NOTICE.................................................................................................... 2
1.2 ISIGNAGER FRAME SERIES OVERVIEW ....................................................................... 2
1.3 ISIGNAGER FRAME SERIES MODEL VARIATIONS......................................................... 2
1.4 FEATURES................................................................................................................... 3
1.5 SYSTEM OVERVIEW.................................................................................................... 3
1.5.1 Front View.......................................................................................................... 3
1.5.2 Bottom Panel...................................................................................................... 4
1.5.3 Rear View........................................................................................................... 5
1.6 PHYSICAL DIMENSIONS.............................................................................................. 6
1.6.1 General Physical Dimensions............................................................................ 6
1.6.2 iSignager-Frame-W07 Physical Dimensions..................................................... 7
1.6.3 iSignager-Frame-08 Physical Dimensions........................................................ 8
1.6.4 iSignager-Frame-W10 Physical Dimensions..................................................... 9
1.6.5 iSignager-Frame-W15 Physical Dimensions................................................... 10
1.7 ISIGNAGER FRAME SERIES SPECIFICATIONS ..............................................................11
1.8 PACKING LIST........................................................................................................... 12
1.9 SOFTWARE -ISIGNAGER ADEXPRESS FOR FRAME .................................................... 13
1.10 SUPPORTED FORMATS ............................................................................................ 13
2 INSTALLATION ......................................................................................................... 14
2.1 HARDWARE INSTALLATION....................................................................................... 15
2.1.1 iSignager Frame Series Set-Up ....................................................................... 15
2.1.2 VGA Connection for Dual Displays................................................................. 17
2.2 MOUNTING THE ISIGNAGER FRAME SERIES.............................................................. 18
2.2.1 Wall Mounting.................................................................................................. 18
2.2.2 Stand Installation............................................................................................. 20
2.2.3 Arm Mounting .................................................................................................. 21
2.2.4 Panel Mounting................................................................................................ 22
2.3 REMOTE CONTROL................................................................................................... 26

iSignager Frame Series
Page v
A CHECK AND MODIFYTHE PLAYER STATUS................................................... 28
A.1 CHECK AND MODIFY THE ISIGNAGER FRAME SERIES STATUS BY SERIAL PORT....... 29
A.1.1 Successful Message—LAN Connection........................................................... 36
A.1.2 Successful Message—Wifi Connection............................................................ 37
A.2 CHECKING CONNECTION......................................................................................... 39
A.2.1 Check the LED................................................................................................. 39
A.2.2 Ping in DOS Environment or Hyper Terminal Session ................................... 39
A.2.2.1 PC............................................................................................................. 39
A.2.2.2 iSignager Frame Series ............................................................................ 39
A.3 ISIGNAGER FRAME WLSERIES NETWORK BEHAVIOR............................................. 40

iSignager Frame Series
Page vi
List of Figures
Figure 1-1: iSignager Frame Series Front View...........................................................................4
Figure 1-2: iSignager Frame Series Bottom Panel View.............................................................5
Figure 1-3: iSignager-Frame-W10 Rear View...............................................................................5
Figure 1-4: iSignager-Frame-W07 Physical Dimensions (millimeters) .....................................7
Figure 1-5: iSignager-Frame-08 Physical Dimensions (millimeters).........................................8
Figure 1-6: iSignager-Frame-W10 Physical Dimensions (millimeters) .....................................9
Figure 1-7: iSignager-Frame-W15 Physical Dimensions (millimeters) ...................................10
Figure 2-1: Unlock the SD Slot Cover.........................................................................................15
Figure 2-2: Insert SD Card ...........................................................................................................16
Figure 2-3: Lock the SD Slot Cover ............................................................................................16
Figure 2-4: Second Display Device Connection........................................................................17
Figure 2-5: Attach Wall Mounting Kit to the Wall ......................................................................18
Figure 2-6: Hook Onto Wall Mounting Kit ..................................................................................19
Figure 2-7: Tighten Retention Screw..........................................................................................20
Figure 2-8: Arm Mounting Retention Screw Holes....................................................................22
Figure 2-9: iSignager-Frame-W07 Panel Opening.....................................................................23
Figure 2-10: iSignager-Frame-08 Panel Opening......................................................................23
Figure 2-11: iSignager-Frame-W10 Panel Opening...................................................................23
Figure 2-12: iSignager-Frame-W15 Panel Opening...................................................................24
Figure 2-13: Tighten the Panel Mounting Clamp Screws (iSignager-Frame-W10) ................25
Figure 2-14: Remote Control .......................................................................................................26

iSignager Frame Series
Page vii
List of Tables
Table 1-1: iSignager Frame Series Model Variations..................................................................3
Table 1-2: General Physical Dimensions .....................................................................................6
Table 1-3: iSignager Frame Series Specifications....................................................................11
Table 1-4: iSignager Frame Series Supported Formats ...........................................................13

iSignager Frame Series
Page 1
Chapter
1
1 Introduction

iSignager Frame Series
Page 2
1.1 Important Notice
NOTE:
This iSignager Frame Series user manual only contains the hardware information.
For the detailed information of the iSignager AdExpress for Frame software that
came with the iSignager Frame Series, please refer to the iSignager AdExpress for
Frame user manual.
1.2 iSignager Frame Series Overview
The iSignager Frame Series is a multimedia display device developed by IEI to display
dynamic, visual and audio contents for a target audience. The flat front panel of iSignager
Frame Series provides IP 64 protection, which effectively wards off dust and water. The
iSignager Frame Series comes with an application software, the iSignager AdExpress for
Frame, to help users to design and transfer dynamic contents for iSignager Frame Series
to display. With the iSignager Frame Series, an advertising station is easily established
and promotes the product and services in the simplest way. Optional wireless connection
enables the display sources to be updated anytime anywhere.
1.3 iSignager Frame Series Model Variations
Eight IEI iSignager Frame Series models are available. The models are listed in
Table 1-1.
Model LCD Resolution Network Second Display
iSignager-Frame-W07 7” wide screen 800 x 480 LAN Yes
iSignager-Frame-08 8” 800 x 600 LAN Yes
iSignager-Frame-W10 10.2” wide screen 1024 x 600 LAN Yes
iSignager-Frame-W15 15.6” wide screen 1366 x 768 LAN Yes

iSignager Frame Series
Page 3
iSignager-Frame-W07WL 7” wide screen 800 x 480 LAN + Wifi Yes
iSignager-Frame-08WL 8” 800 x 600 LAN + Wifi Yes
iSignager-Frame-W10WL 10.2” wide screen 1024 x 600 LAN + Wifi Yes
iSignager-Frame-W15WL 15.6” wide screen 1366 x 768 LAN + Wifi Yes
Table 1-1: iSignager Frame Series Model Variations
1.4 Features
Some of the iSignager Frame Series features are listed below.
7”/8”/10.2”/15.6” TFT LCD
Fully functional remote control
Built-in speakers
Support wall/stand/arm mounting
Supports full spectrum of media formats
Supports second display
Contents can be stored in SD card or USB 2.0 flash drive
Uploading content from remote to the iSignager Frame Series through
Network management function
Optional 802.11b/g wireless module and PIFA antenna
IP 64 compliant front panel
RoHS compliant
1.5 System Overview
1.5.1 Front View
The front of the iSignager Frame Series is a flat panel TFT LCD screen surrounded by an
ABS/PC plastic frame. The iSignager Frame Series also includes one infrared sensor and
one power LED on the front panel:
Figure 1-1 shows the front view of the iSignager Frame Series.

iSignager Frame Series
Page 4
Figure 1-1: iSignager Frame Series Front View
1.5.2 Bottom Panel
All peripheral device connectors are located on the bottom panel of the iSignager Frame
Series. The following is a list of the bottom panel peripheral device connectors used on the
iSignager Frame Series.
12V power connector: Connects to power adapter.
Power switch: Turn on or turn off the system.
RS-232 serial connector: This port can be connected to three COM ports
(COM 0, 3, 4). If a general RS-232 cable is used, it only connects to COM 0
for displaying player debug message (Please refer to Appendix 2.3A.1). For
other COM port connection (COM3 and COM4), a special cable is needed.
RJ-45 Ethernet connector: Supports 10/100M BASE-T LAN for updating
display content, firmware and player settings via network interface.
SD card slot: For installing SD card with media content created in the
iSignager AdExpress for Frame.
USB connector: For installing USB flash drive to update display content,
firmware and player settings.
Audio out jack: Connects to audio input connector of the second display
device.

iSignager Frame Series
Page 5
VGA connector: Connects to VGAconnector of the second display device.
Figure 1-2 shows the bottom panel of the iSignager Frame Series digital signage display.
Figure 1-2: iSignager Frame Series Bottom Panel View
1.5.3 Rear View
The rear panel features fan ventilation holes and four retention screw holes that support a
VESA FDMI (MIS-D 75 or MIS-D 100) wall-mounting bracket, a stand or an arm. Two
internal 1.5W spears are located on the two side panels. Figure 1-3 shows the rear view
of the iSignager-Frame-W10.
Figure 1-3: iSignager-Frame-W10 Rear View

iSignager Frame Series
Page 6
1.6 Physical Dimensions
The following sections describe the physical dimensions for the iSignager Frame Series.
1.6.1 General Physical Dimensions
General physical dimensions for the iSignager Frame Series are shown in Table 1-2.
Model Width
(mm)
Height
(mm)
Depth
(mm)
iSignager-Frame-W07 226.00 140.00 40.18
iSignager-Frame-08 234.00 177.00 43.00
iSignager-Frame-W10 279.79 185.39 48.18
iSignager-Frame-W15 400.00 273.00 62.90
Table 1-2: General Physical Dimensions

iSignager Frame Series
Page 7
1.6.2 iSignager-Frame-W07 Physical Dimensions
The physical dimensions of the iSignager-Frame-W07 are shown in Figure 1-4.
Figure 1-4: iSignager-Frame-W07 Physical Dimensions (millimeters)

iSignager Frame Series
Page 8
1.6.3 iSignager-Frame-08 Physical Dimensions
The physical dimensions of the iSignager-Frame-08 are shown in Figure 1-5.
Figure 1-5: iSignager-Frame-08 Physical Dimensions (millimeters)

iSignager Frame Series
Page 9
1.6.4 iSignager-Frame-W10 Physical Dimensions
The physical dimensions of the iSignager-Frame-W10 are shown in Figure 1-6.
Figure 1-6: iSignager-Frame-W10 Physical Dimensions (millimeters)

iSignager Frame Series
Page 10
1.6.5 iSignager-Frame-W15 Physical Dimensions
The physical dimensions of the iSignager-Frame-W15 are shown in Figure 1-7.
Figure 1-7: iSignager-Frame-W15 Physical Dimensions (millimeters)

iSignager Frame Series
Page 11
1.7 iSignager Frame Series Specifications
Table 1-3 shows the iSignager Frame Series specifications.
iSignager-Frame -W07 -08 -W10 -W15
LCD Size 7" wide screen 8" 10.2" wide screen 15.6” wide screen
Max. Resolution 800 x 480 800 x 600 1024 x 600 1366 x 768
Brightness (cd/m2) 300 250 400 250
Contrast 500:1 400:1 400:1 500:1
LCD Color 262K 262K 262K 16.7M
Pixel Pitch (mm) 0.1905 0.2025 0.2175 0.252
View Angle (H / V) 140/120 130/120 140/110 90/65
Backlight MTBF (Hrs) 50000 30000 40000 50000
Motion Sensor Yes Yes Yes No
Secondary Display 1 x VGA 1 x VGA 1 x VGA 1 x VGA
Bundled Software iSignager AdExpress for Frame
USB 1 x USB 2.0 port
Ethernet 1 x 10/100BASE-T
802.11b/g Wireless Optional
Serial Port 1 x RS-232
Audio Out 2 x AMP 1.5W speakers
1 x Audio jack
Storage 1 x SD card slot (Specs 2.0)
Power Input Voltage 12 V DC input
Power Adapter 40 W
VESA Mounting MIS-D 75 MIS-D 75 MIS-D 100 MIS-D 100
Dimension (WxHxD) (mm) 226 x 140 x 40 234 x 177 x 43 280 x 185 x 48 400 x 273 x 63
IR Sensor/Remote Control Yes (reset, volume control, brightness control, sleep/wake-up time setup)
Operation Temperature 0°C ~50°C
IP Level IP 64
Safety UL/CUL, CB, BSMI
EMC CE/EMC, FCC, BSMI
N/G Weight 0.6 kg 0.8 kg 1.4 kg 3.3 kg
Table 1-3: iSignager Frame Series Specifications

iSignager Frame Series
Page 12
1.8 Packing List
The iSignager Frame Series is shipped with the following components. Should there be
any missing parts or defects in the package, please contact IEI immediately.
Quantity Item Image
1 iSignager Frame Series
1 AC power adaptor
1 Power cord
1 2GB SD card
1 SD slot key
1 OSD remote control
1 iSignager AdExpress for Frame software
companion CD