IEI Technology MMD-4300 User manual

MMD-4300 Series Medical LCD Monitor
Page i
MMD-4300 Series Medical LCD Monitor

MMD-4300 Series Medical LCD Monito
r
Page ii
Revision
Date Version Changes
2007-11 1.01 Modified OSD images
2007-10 1.00 Initial Release

MMD-4300 Series Medical LCD Monitor
Page iii
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.

MMD-4300 Series Medical LCD Monito
r
Page iv
Manual Conventions
WARNING!
Warnings appear where overlooked details may cause damage to the equipment or result
in personal injury. Warnings should be taken seriously. Warnings are easy to recognize.
The word “warning” is written as “WARNING,” both capitalized and bold and is followed by
text. The text is the warning message. A warning message is shown below:
WARNING:
This is an example of a warning message. Failure to adhere to warning
messages may result in permanent damage to the MMD-4300 Series
or personal injury to the user. Please take warning messages seriously.
CAUTION!
Cautionary messages should also be heeded to help reduce the chance of losing data or
damaging the MMD-4300 Series. Cautions are easy to recognize. The word “caution” is
written as “CAUTION,” both capitalized and bold and is followed. The italicized text is the
cautionary message. A caution message is shown below:

MMD-4300 Series Medical LCD Monitor
Page v
CAUTION:
This is an example of a caution message. Failure to adhere to cautions
messages may result in permanent damage to the MMD-4300 Series.
Please take caution messages seriously.
NOTE:
These messages inform the reader of essential but non-critical information. These
messages should be read carefully as any directions or instructions contained therein can
help avoid making mistakes. Notes are easy to recognize. The word “note” is written as
“NOTE,” both capitalized and bold and is followed by text. The text is the cautionary
message. A note message is shown below:
NOTE:
This is an example of a note message. Notes should always be read.
Notes contain critical information about the MMD-4300 Series. Please
take note messages seriously.

MMD-4300 Series Medical LCD Monito
r
Page vi
Packing List
NOTE:
If any of the components listed in the checklist below are missing,
please do not proceed with the installation. Contact the IEI reseller or
vendor you purchased the MMD-4300 series from or contact an IEI
sales representative directly. To contact an IEI sales representative,
please send an email to [email protected].
The items listed below should all be included in the MMD-4300 Series package.
 1 x MMD-4300 Series LCD monitor
 1 x Monitor stand
 1 x Power adapter
 1 x Power cord (US)
 2 x DVI-D cables
 1 x USB cable (Type A to Type B)
 1 x User manual and utility CD
Images of the above items are shown in Chapter 3.

MMD-4300 Series Medical LCD Monitor
Page vii
Safety Precautions
 Prior to installing, moving and modifying the monitor, make sure the power is
turned off and the power cord is disconnected.
 Do not apply voltage levels that exceed the specified voltage range. Doing so will
cause fire or an electric shock.
 Electric shocks can occur if the panel is opened. Do not drop or insert any object
into the ventilation openings of the monitor.
 Only qualified engineers from certified system integrators are allowed to make
necessary functional modifications to the monitor.
 If considerable amount of dust, water or fluids entered the monitor, turn off the
power supply immediately, unplug the power cord and contact the monitor vendor.
 Explosions may occur with installations in environments where flammable gases
are present.
 Grounding reliability can only be achieved when the equipment is connected to an
equivalent receptacle marked “Hospital Only” or “Hospital Grade”.
 This device is intended to be used: (1) outside a “patient vicinity” area or (2) within
a “patient vicinity” area such as consulting rooms.
 The signal input parts or signal output parts (SIP/SOP) need to be connected
properly and any unused SIP/SOP shall not be accessible to unqualified
personnel after the LCD is integrated into a medical system.
 The unit is for exclusive interconnection with IEC 60XXX certified equipment
outside of patient environment and IEC 60601-1 certified equipment inside the
patient environment.
 This device complies with EN60601-1-2. To minimize the interference from other
equipment, a minimum 0.5 m distance shall be kept from other potential
electromagnetic sources, such as cell phones, etc.
 Equipment connected to the analog or digital interfaces must comply with the
respective IEC standards (e.g. IEC 60950 for data processing equipment and IEC
60601-1 for medical equipment).

MMD-4300 Series Medical LCD Monito
r
Page viii
 To fully disengage power to the unit, disconnect the power cord from its AC outlet.
Do not remove any of the display housings. There are no user serviceable parts
inside the monitor. Refer servicing to qualified service personnel.
 All configurations shall comply with the current version of the IEC 60601-1-1
safety requirements for medical electrical systems.
 To maintain the highest level of performance, it is recommended that this product
be replaced after five years of use.
FURTHER PRECAUTIONS
 Do not drop the monitor against a hard surface. Doing so will damage the display.
 Do not strike or exert excessive force onto the panel.
 Touching the LCD panel using a sharp object will cause damage to the display.
 Avoid environments exposed to direct sunlight, dust or chemical vapors.
 The ambient temperature of the installation site should be observed and
controlled to avoid overheating the monitor.
 Condensation might form inside of the monitor chassis if exposed to sudden
changes in temperature.
 Carefully route the power cord, so that people cannot step on it. Do not place
anything over the power cord or bend it.
 If the equipment should be left unused for an extended period of time, disconnect
it from the power source to avoid damage by transient over-voltage.
 If any of the following situations arise, have the equipment checked by qualified
service personnel:
o The power cord or plug is damaged.
o Liquid has penetrated into the equipment.
o The equipment has been exposed to moisture.
o The equipment does not work properly, or cannot be made to work
according to the user manual.
o The equipment has been dropped and damaged.
o The equipment shows obvious signs of damage.

MMD-4300 Series Medical LCD Monitor
Page ix
WARNING:
Any changes or modifications made to the equipment that are not
expressly approved by the relevant standards could void the authority
to operate the equipment.
ADDITIONAL INFORMATION AND ASSISTANCE
MAINTENANCE AND CLEANING
Prior to cleaning any part or component of the monitor, please read the details below.
 Except for the properly installed front LCD panel, never spray or squirt liquids
directly onto any other component. To clean the front panel, please rub it with a
piece of soft dry cloth or a slightly moistened cloth.
 The interior of the LCD monitor does not require cleaning. Keep fluids away from
the LCD monitor interior.
 Be cautious of all small removable components when vacuuming the monitor.
 Turn the system off before cleaning the LCD monitor.
 Never drop any objects or liquids through the openings of the LCD monitor.
 Be cautious of any possible allergic reactions to solvents or chemicals used when
cleaning the monitor.
 Avoid eating, drinking and smoking within vicinity of the monitor.

MMD-4300 Series Medical LCD Monito
r
Page x
CLEANING TOOLS
Some components in the monitor may only be cleaned using a product specifically
designed for the purpose. In such case, the product will be explicitly mentioned in the
cleaning tips. Below is a list of items to use when cleaning the computer or computer
peripherals.
 Cloth – Although paper towels or tissues can be used, a soft, clean piece of dry
cloth is recommended when cleaning the monitor.
 Using solvents – The use of solvents is not recommended when cleaning the
monitor as they may damage the plastic parts.
 Vacuum cleaner – Using a vacuum specifically designed for computers is one of
the best methods of cleaning the monitor. Over dust and dirt can restrict the
airflow in a computer and cause circuitry to corrode.
 Cotton swabs - Cotton swaps moistened with rubbing alcohol are excellent tools
for wiping hard to reach areas.
 Foam swabs - Whenever possible, it is best to use lint free swabs such as foam
swabs for cleaning.
ESD PRECAUTIONS
Observe all conventional anti-ESD methods while handling the components contained
within the LCD should the need arise for adding a functionality. The use of a grounded
wrist strap and an anti-static work pad is recommended. Avoid dust and debris or other
static-accumulating materials in the work area.