IEI Technology WSB-9454 User manual

1
PICMG 1.0 CPU Card support LGA775 Intel®Core 2 Duo,
Pentium®D/4, Celeron®DCPUwith VGA/DVI,
Dual PCIE GbE LAN and SATAII
WSB-9454
Quick Installation Guide
Version 1.2
Aug. 31, 2009
Package Contents
WSB-9454 package includes the following items:
z1 x WSB-9454 Single Board Computer
z1 x mini jumper pack
z1 x ATA flat cable
z1 x Dual RS-232 cable
z1 x SATA Power cable
z2 x SATA cable
z1 x KB/MS Y cable
z1 x Dual Ports USB cable
z1 x IO-KIT-001-R20 (WSB-9454DVI only)
z1 x Utility CD
z1 x QIG (quick installation guide)
©2006 Copyright by IEI Technology corp.
All rights reserved.

2
Specifications
zCPU: LGA 775 Intel®Core 2 duo, Pentium®D/4, Celeron®D with
533/800/1066 MHz FSB
zSystem Chipset: Intel®945G + ICH7
zBIOS: AMI Flash BIOS
zSystem Memory
4x240-pin Dual-channel DDR2 400/533/667 MHz DRAM up to 4GB
zEthernet: Dual Broadcom BCM5787M PCIe interface GbE controller
zI/O Interface
2 x RS232
7 x USB 2.0 (1 on rear, 6 on board by pin-header)
1 x IDE
1 x LPT
1 x FDD
4 x SATAII
1 x PS/2 for KB/MS
1 x 5-pin header for KB
1 x Infrared Interface
zDisplay:
VGA integrated in Intel®945G
DVI by Silconimage SIL1362(WSB-9454DVI Only)
zDigital I/O: 8 bit digital I/O, 4 input /4 output
zAudio: 5.1 Channel AC’97 Audio Kit with Realtek ALC655
7.1 Channel HD Audio Kit with Realtek ALC883
zWDT: Software programmable supports 1-255 sec. System reset
zPower Supply: ATX Power, AT/ATX Mode
zPower Consumption:[email protected],+12V@ 2.79A
(3D Mark 2001 with Intel®Core® 2 Duo E6700 2.66GHz, DDR2
800MHz 2GB*2)
zTemperature: 0 ~ 60°C( 32 ~ 140°F)
zHumidity: 5% ~ 95% non-condensing
zDimension: (L)338mm x (W)122mm
zWeight: GW: 1.2Kg

3
Ordering Information
WSB-9454-R12
PICMG 1.0 CPU Card support LGA775 Intel®Core 2 Duo, Pentium®D/4,
Celeron®D 1066MHz processor, VGA, Dual PCIE GbE and SATAII
WSB-9454DVI-R12
PICMG 1.0 CPU Card support LGA775 Intel®Core 2 Duo, Pentium®D/4,
Celeron®D 1066MHz processor, VGA/DVI, Dual PCIE GbE and SATAII
AC-KIT08R-R10
5.1 Channel AC’97 Audio Kit with Realtek ALC655
AC-KIT883HD-R10
7.1 Channel HD Audio Kit with Realtek ALC883 supports dual audio streams
CF-520-RS: CPU Clooer
32200-000017-RS: FDD cable
19800-000049-RS: LPT cable
CF-775A-RS: CPU cooler

4
Jumpers setting and Connectors
LABEL FUNCTION
J_CMOS1 Clear CMOS Jump
JLAN_PWR1 WOL Setting Jump
KB_MS1 PS/2 MOUSE & KEYBOARD connector
LAN1
LAN2 RJ45 LAN Connectors
VGA1 VGA 15-pin Female connector
USB_C6 External USB Port connector
PIDE1 IDE connector
FDD1 FDC connector
LPT1 Parallel Port connector
COM1
COM2 Internal Serial Port 10-pin connectors
USB01
USB23
USB45 Internal 6 Ports USB connectors
IR1 Infrared Interface connector
CPU_FAN1 CPU Fan Connector
ATXCTL1 AT/ATX Mode Select jump
SATA1
SATA2
SATA3
SATA4
Serial ATA connectors
DIO1 Digital I/O connector
F_PANEL1 PWR & RST Buttons & Speaker and Indicators
J_AUDIO1 Audio Connector
KB1 Internal 5-pin Header Keyboard connector
DVI1 DVI-D connector (WSB-9454DVI Only)
CPU12V1 ATX-12V CPU Power Input connector
JSPI1 Flash SPI ROM connector
DDRII-1
DDRII-2
DDRII-3
DDRII-4
DDR2 DRAM Slots

5
J_CMOS1 : Clear CMOS Setup
J_CMOS1 DESCRIPTION
Short 1-2
(default)* Keep CMOS Setup (Normal Operation)
Short 2-3 Clear CMOS Setup
JLAN_PWR1:WOL setting
JLAN_PWR1 DESCRIPTION
Short 1-3 LAN 2 WOL Enable
Short 2-4 LAN 1 WOL Enable(Default)
Short 3-5 LAN 2 WOL Disable(Default)
Short 4-6 LAN 1 WOL Disable
KB1 : Internal 5-pin Header Keyboard Connector
PIN NO. DESCRIPTION
1 KEYBOARD CLOCK
2 KEYBOARD DATA
3 N/C
4 GND
5 VCC +5V
ATXCTL1 : AT/ATX Mode Select jump
PIN NO. DESCRIPTION
Short 1-2 AT Mode
Open
(default)* ATX Mode
ATXCTL1 : Backplane to Mainboard Connector
PIN NO. DESCRIPTION
1 GND
2 PS_ON#
3 5VSB

6
FDD1: FDC Connector
PIN DESCRIPTION PIN DESCRIPTION
1 GND 2 REDUCE WRITE
3 GND 4 N/C
5 N/C 6 N/C
7 GND 8 INDEX#
9 GND 10 MOTOR ENABLE A#
11 GND 12 DRIVE SELECT B#
13 GND 14 DRIVE SELECT A#
15 GND 16 MOTOR ENABLE B#
17 GND 18 DIRECTION#
19 GND 20 STEP#
21 GND 22 WRITE DATA#
23 GND 24 WRITE GATE#
25 GND 26 TRACK 0#
27 GND 28 WRITE PROTECT#
29 GND 30 READ DATA#
31 GND 32 SIDE 1 SELECT#
33 GND 34 DISK CHANGE#
USB01, USB23, USB45: Internal USB Connector
PIN DESCRIPTION PIN DESCRIPTION
1 VCC +5V 2 GND
3 DATA- 4 DATA+
5 DATA+ 6 DATA-
7 GND 8 VCC +5V
IR1: Infrared Interface Connector
PIN DESCRIPTION
1 VCC +5V
2 NC
3 IR-RX
4 GND
5 IR-TX
CPU_FAN1 :
CPU Fan Connector
PIN DESCRIPTION
1 GND
2 +12V
3 Rotation Signal
4 Control

7
COM1,COM2 :Internal Serial Port 10-pin Connectors
Connector Ports Address Interrupt
COM1 COM1 3F8 IRQ4
COM2 COM2 2F8 IRQ3
CPU12V1 : CPU POWER Input Connector
PIN DESCRIPTION PIN DESCRIPTION
1 GND 2 GND
3 +12V 4 +12V
DIO1 : Digital Input / Output Connector
PIN DESCRIPTION PIN DESCRIPTION
1 GND 2 VCC +5V
3 Output 0 4 Output 1
5 Output 2 6 Output 3
7 Input 0 8 Input 1
9 In
p
ut 2 10 In
p
ut 3
F_PANEL1 : PWR & RST Buttons & Speaker and Indicators
PIN DESCRIPTION PIN DESCRIPTION
1 PWRLED + 2 Speaker +
3 N/C 4 N/C
Power LED 5 PWRLED - 6 N/C
7 PWRBTN- 8 Speaker -
Speaker
PWRBTN 9 PWRBTN+ 10 N/C
11 HDLED+ 12 Reset +
HDDLED 13 HDLED- 14 Reset - RESET
COM1,COM2: Internal Serial Port 10-pin Connectors
PIN DESCRIPTION PIN DESCRIPTION
1 DCD# 2 DSR#
3 RXD 4 RTS#
5 TXD 6 CTS#
7 DTR# 8 RI#
9 GND 10 NC

8
LPT1 : Parallel Port Connector
PIN DESCRIPTION PIN DESCRIPTION
1 STROBE# 14 AUTO FORM FEED #
2 DATA0 15 ERROR#
3 DATA1 16 INITIALIZE#
4 DATA2 17 PRINTER SELECT LN#
5 DATA3 18 GND
6 DATA4 19 GND
7 DATA5 20 GND
8 DATA6 21 GND
9 DATA7 22 GND
10 ACKNOWLEDGE# 23 GND
11 BUSY 24 GND
12 PAPER EMPTY 25 GND
13 PRINTER SELECT 26 N/C
J_AUDIO1: Audio Connector
PIN DESCRIPTION PIN DESCRIPTION
1 SYNC 2 BITCLK
3 SDOUT 4 PCBEEP
5 SDIN 6 RST#
7 VCC +5V 8 GND
9 +12V
JSPI1:Flash SPI ROM connetor
PIN NO. DESCRIPTION PIN NO. DESCRIPTION
1 +3.3V 5 GND
2 CS0# 6 CLK
3 SO0 7 SI
4 N/C 8 N/C

9
DVI1 : DVI Connector (WSB-9454DVI Only)
PIN DESCRIPTION PIN DESCRIPTION
1 Data 2- 14 VCC(+5V)
2 Data 2+ 15 GND
3 GND 16 Hot Plug Detect.
4 N/C 17 Data 0-
5 N/C 18 Data 0+
6 DDC Clock 19 GND
7 DDC Data 20 N/C
8 N/C 21 N/C
9 Data 1- 22 GND
10 Data 1+ 23 Clock +
11 GND 24 Clock -
12 N/C 25 GND
13 N/C
PIDE1: IDE Interface Connector
PIN DESCRIPTION PIN DESCRIPTION
1 RESET# 2 GND
3 DATA 7 4 DATA 8
5 DATA 6 6 DATA 9
7 DATA 5 8 DATA 10
9 DATA 4 10 DATA 11
11 DATA 3 12 DATA 12
13 DATA 2 14 DATA 13
15 DATA 1 16 DATA 14
17 DATA 0 18 DATA 15
19 GND 20 N/C
21 IDE DRQ 22 GND
23 IOW# 24 GND
25 IOR# 26 GND
27 IDE CHRDY 28 BALE – DEFAULT
29 IDE DACK 30 GND
31 INTERRUPT 32 N/C
33 SA1 34 PDIAG#
35 SA0 36 SA2
37 HDC CS0# 38 HDC CS1#
39 HDD ACTIVE# 40 GND

10
Board Layout: Jumper and Connector Locations