IKEA FÖRDELAKTIG User manual

GB
DE
FR
IT
NL
FÖRDELAKTIG

ENGLISH 4
DEUTSCH 30
FRANÇAIS 57
ITALIANO 85
DUTCH 111
2
1345
Please refer to the last page of
this manual for the full list of IKEA
appointed Authorized Service
Centre and relative national phone
number
2
1345
2
1345
Consultare l’ultima pagina di
questo manuale dove è riportato
l’elenco completo dei Centri
Assistenza IKEA Autorizzati con i
relativi numeri telefonici nazionali.
2
1345
Consultez la dernière page de
ce manuel contenant la liste
complète des services Après-
vente agréés IKEA avec les
numéros de téléphone nationaux
correspondants.
Konsultieren Sie die letzte Seite
dieser Bedienungsanleitung,
auf der die vollständige Liste der
nationalen autorisierten IKEA
Kundendienststellen mit den
entsprechenden Telefonnummern
aufgelistet ist.
2
1345
Op de laatste bladzijde van
deze handleiding vindt u de
complete lijst van de door IKEA
erkende servicebedrijven met
de bijbehorende nationale
telefoonnummers.

4 ENGLISH
Contents
Safety information
For your safety and correct operation of the
appliance, read this manual carefully before
installation and use. Always keep these instructions
with the appliance even if you move or sell it. Users
must fully know the operation and safety features of
the appliance.
Induction systems of these hobs meet the requirements
of EMC standards as well as the EMF Directive and
should not interfere with other electronic devices. Heart
pacemakers users or other electronic implants users
should clarify with their medical doctor or with the
manufacturer of the implants whether these devices

The wire connection has to be done by special-
ized technician. Before proceeding with electrical
connection please refer to Chapter ELECTRICAL
CONNECTION.
For appliances with supply cords, the arrangement of
the terminals, or the length of the conductors between
the cord anchorage and the terminals, shall be such that
the current carrying conductors become taut before
the earthing conductor if the cord slips out of the cord
Safety information 4
Safety instruction 9
Product description 12
Indicators 12
Control Panel 13
Cooking zone control panel 15
Extractor control panel 16
Cookware guidance 17
Daily use 18
Troubleshooting 20
Power Management 21
Hob Extractor Technical Data 22
Extractor Energy efficiency 23
Hob Energy efficiency 24
Rating Plate 24
Electrical connection 25
Environment concerns 27
IKEA GUARANTEE 27

5 ENGLISH
anchorage.
• The manufacturer will not be held liable for any
damages resulting from incorrect or improper
installation.
• Check that the mains voltage corresponds to that
indicated on the rating plate fixed to the inside of the
product.
• Means for disconnection must be incorporated in the
fixed wiring in accordance with the wiring rules.
• For Class I appliances, check that the domestic power
supply guarantees adequate earthing.
• Connect the extractor to the exhaust flue through
an adequate pipe. Please refer to the purchasable
accessories shown in the installation manual (if circular
pipe: minimum diameter 120 mm). The route of the flue
must be as short as possible.
• Connect the product to the power net by using an
omnipolar switch.
• Regulations concerning the discharge of air have to be
fulfilled.
• Do not connect the extractor appliance to exhaust ducts
carrying combustion fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-electrical
appliances (e.g. gas burning appliances), a sufficient
degree of aeration must be guaranteed in the room in
order to prevent the backflow of exhaust gas. When the
cooker appliance is used in conjunction with appliances
supplied with energy other than electric, the negative
pressure in the room must not exceed
0,04 mbar to prevent fumes being drawn back into the
room by the cooker appliance.
• The air must not be discharged into a flue that is used

6 ENGLISH
for exhausting fumes from appliances burning gas or
other fuels.
• If the supply cord is damaged, it must be replaced
from the manufacturer or its service agent or similarly
qualified person in order to avoid a hazard.
• Connect the plug to a socket complying with current
regulations, located in an accessible place.
• With regards to the technical and safety measures to be
adopted for fume discharging it is importat to closely
follow the regulations provided by the local authorities.
WARNING: Before installing the appliance, remove
the protective films.
• Use only screws and small parts in support of the
appliance.
WARNING: Failure to install the screws or fixing
device in accordance with these instructions may
result in electrical hazards.
• Do not look directly at the light through optical devices
(binoculars, magnifying glasses…).
• Cleaning and user maintenance shall not be made by
children without supervision.
• Children should be supervised to ensure that they do
not play with the appliance.
• This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person
responsible for their safety.
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience

7 ENGLISH
and knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children
shall not play with the appliance.
WARNING: The appliance and its accessible parts
become hot during use.
Care should be taken to avoid touching heating elements.
Children less than 8 years of age shall be kept away
unless continuously supervised.
• Clean and/or replace the Filters after the specified time
period (Fire hazard). See paragraph Care and Cleaning.
• There shall be adequate ventilation of the room when
the appliance is used at the same time as appliances
burning gas or other fuels (not applicable to appliances
that only discharge the air back into the room).
WARNING:
appliance to avoid the possibility of electric shock.
• Do not switch on a device if the surface is cracked or
there is a damage to the material thickness.
• Do not touch the appliance with wet parts of the
body.
• To clean the product a steam cleaner is not to be
used.
• Metallic objects such as knives, forks, spoons and lids
should not be placed on the hob surface since they
can get hot.
• 
and do not rely on the pan detector.
WARNING: Unattended cooking on a hob with fat or




8 ENGLISH
blanket.
CAUTION: The cooking process has to be supervised.
A short term cooking process has to be supervised
continuously.
• The appliance is not intended to be operated by
means of an external timer or separate remote-control
system.
WARNING:
cooking surfaces.
• Ensure that the device is installed in a way that allows
to disconnect it from the power supply, with a contact
opening distance (3 mm) that ensures complete
disconnection in category III overvoltage conditions.
• Ensure that the device is not exposed to atmospheric
agents (rain, sun).
• Ensure that the ventilation of the appliance is in
accordance with the manufacturer‘s instructions.

9 ENGLISH
General recommendations
• Never use scouring pads, steel wool, muriatic
acid or other products which could scratch or
mark the surface.
• For safety reasons, do not clean the appliance
with steam blasters or high-pressure cleaners.
• Foods that accidentally fall or settle on
the surface, on the functional or aesthetic
elements of the hob must not be eaten.
Cabinet requirements
• The cooking hob is intended to be built into
the worktop above a kitchen cabinet of 800
mm width or more.
• 
and standards for low voltage installations

observed.
• 
materials and veneered wood) must be
assembled with heat-resistant adhesives (min.
85°C): Unsuitable materials and adhesives can
result in warping and detachment.
• 
room for the electrical connections of the
appliance. Suspended kitchen cabinets above
the appliance must be installed at a distance
that provides enough room for comfortable
working process.
• The use of hard wood decorative borders
around the worktop behind the appliance is
allowed, in this case the minimum distance
remains as indicated on the installation
illustrations.
• Positioning and dimensions of the cut-out for
built-in appliance is shown in the illustration
below. The measurements shown are
only valid if the following condition is met:
worktop overhang to cabinet front is 35mm.
• Minimum distance between built-in appliance
and any cabinet above it is 500mm.
490+2 mm
773+2 mm
555 mm
18 - 40mm
Safety instruction
Min. 500 mm
• To prevent leakage of liquid between the
edge of the hob and the countertop, place
the adhesive seal provided along the entire
outer edge of the hob before assembly.
Please refer to Assembly Instruction.
Electrical connection
• The wire connection has to be done by
specialized technician.
• This appliance has a Type “Y” attachment
and requires at least a power supply cord
   
THREE-PHASE connection: min. section of the
conductors: 2,5 mm². External diameter of the
supply cord: min. 7 mm - max. 15 mm.
• Connection terminals are revealed when the
connection box cover is removed.
• Make sure the characteristics of the
household electrical system (voltage,
maximum power and current) are compatible
with those of the appliance.
• Connect the appliance like shown in the
diagram (in accordance with the mains
voltage and country standard reference).
• We suggest to use power supply cord 5 x

In case of use of power supply cord 5 x 2,5

to be followed: for three-phase connection
separate the 2 wires crimped together and
remove the light blue sheaths from grey
wires. Please refer to wiring diagram.
Use
• The extractor appliance has been designed
exclusively for domestic use to eliminate
kitchen smells.
• Never use the appliance for purposes other
than for which it has been designed.
• Deep fat fryers must be continuously
monitored during use: overheated oil can

10 ENGLISH
burst.
• Do not operate the appliance with an
external time switch or a separate remote
control system.
• The appliance shall not be installed behind a
decorative door in order to avoid overheating.
• To avoid damaging the appliance, do not
climb onto the appliance.
• To avoid damaging the silicon grouting, do
not put hot cookware on the frame.
• Do not cut or prepare food on the surface
or drop hard objects onto it. Do not drag
cookware across the surface.
Care and Cleaning

supply before carrying out any maintenance work.
Charcoal Filter
• 
assembly instruction) can be regenerated.

washed and regenerated every 3-4 months
(or more frequently if the hood is subject to
intensive use), up to a Max. of 8 regeneration
cycles (in case of particularly intensive use it
is recommended that you do not exceed 5
 
the service (see table in the end of booklet)
Regeneration procedure:
• Wash in the dishwasher at a MAX
temperature of 70° or hand wash in hot
water without using abrasive sponges (do not
use detergents!).
• Dry in the oven at a MAX temperature of
70° for 2 hours (it is recommended to read
carefully the user manual and the assembly
instruction of the oven of your own).
Cast iron grid
• Do not wash in a dishwasher. Clean the
Grid with hot water and neutral soap,
without using abrasive sponges (do not use
detergents!).
Grease Filters
• 
according to below time intervals, to maintain
good performance of the hood and to
   
excessive grease build-up.
•  
months of operation, or more frequently for
particularly heavy usage, and can be washed
in a dishwasher.
Overflow (upper) is part of the grease filter and
must be checked after each cooking or whenever
liquid has bee spilled on the hob. Rinse under
warm water and remove food to prevent smell
and lime scale.

11 ENGLISH
Water collector
For a standard use is recommended to check
and emptying the collector every two weeks.
• Remove the drawer before checking the
water collector regularly, especially after a
large amount of liquid has been spilled.
Release the lock (1) and pull the water
collector down (2) then wash with warm
water or in the dishwasher.
1
2
Cleaning the appliance
• Clean the appliance after every use in order
to prevent food residues from burning on.
Cleaning dried-on and burnt-on dirt requires

• To clean everyday dirt, use a soft cloth or
sponge with water and a suitable cleaning
agent. Follow the manufacturer‘s advice with
regard to cleaning agents. We recommend
using protective cleaning agents.
• Remove encrusted dirt, e.g. from milk that
has boiled over, with a glass ceramic hob
scraper while the hob is still warm. Please
follow the manufacturer‘s advice with regard
to the scraper.
• Remove sugary foods, such as marmalade,
that have boiled over with a glass ceramic
hob scraper while the hob is still warm.
Otherwise, this could damage the glass
ceramic surface.
• Remove melted plastic with a glass ceramic
hob scraper while the hob is still warm.
Otherwise, this could damage the glass
ceramic surface.
• Remove limescale stains using a small
amount of lime-dissolving solution, e.g.
vinegar or lemon juice, when the hob has
cooled down. Then clean again with a damp
cloth.

12 ENGLISH
Product description
Single cooking zone (220 x 185 mm) 2100W, with Booster 3700W
Single cooking zone (220 x 185 mm) 2100W, with Booster 3700W
Single cooking zone (220 x 185 mm) 2100W, with Booster 3700W
Single cooking zone (220 x 185 mm) 2100W, with Booster 3700W
Control Panel
6
Extractor
+ Bridge cooking area (220 x 370 mm) 3700W
+ Bridge cooking area (220 x 370 mm) 3700W
6
Pan detection
Every cooking zone is equipped with pan
detection. The pan detection recognises
cookware with a magnetisable base that is
suitable for use with induction hobs.
If the cookware is removed during operation or
unsuitable cookware is used, the display near
 .
If there is no cookware placed on the cooking
zone during the pan detection time of 10
seconds:

after 10 seconds.
- The display of each cooking zone shows .
Residual heat indicator

an “H” remains illuminated on the panel as long
as there is a risk of burns.
Indicators

13 ENGLISH
Control Panel
Hob extractor ON/OFF.
Press to turn ON. Press again to turn OFF.
By default, when the Hob extractor is turned on the hood is in
automatic mode and the led will turn on.
Touch (press) the selection bar to deactivate automatic mode and
work with the extractor fan in manual mode.
The led 
Activating the Timer
Press and hold the button for 5 seconds, the hood will be in delay
mode with a preset timer of 15 min.
The delay indicator led on the hood will turn on .
Press and hold the button again for 5 seconds to deactivate the
delay.


pressed), while the display 
The countdown is not visible, the visual feedback is the led .
Select the Cooking zone to set an independent timer.
This is a countdown, which can be set for each cooking zone, even
simultaneously.
At the end of the set period the cooking zones will automatically
shut down and an acoustic signal informs of it.
Activation/Regulation of the hob timer:
Press button several times to select the cooking zone you want to
activate.
The relative icon on the cooking zone will light up.
When the desired cooking zone is selected, regulate the duration of
the timer:
Press + to increase the automatic shutdown time.
Press - to decrease the automatic shutdown time.

14 ENGLISH
Stop&Go / Recall
This function allows any function active on the hob to be suspended
/ restarted, bringing the cooking power to zero. Press to activate,
press again and slide the slider shown (close to the pause function
) all the way from left to right to deactivate.
Note: If after 10 minutes, the Pause function is not deactivated, the

This function allows all the hob settings to be recovered, in the event
of accidental shutdown.
Activation:
- Turn the hob back on.
- Press within 6 seconds.
Increase/Decrease the timer for cooking zone.
 
 
+
Locking/unlocking the hob
Allows the hob settings to be locked to prevent accidental tampering,
leaving the functions that have already been set active. Repeat the
operation to deactivate.
Key Lock. Touch and simultaneously for a few seconds.

15 ENGLISH
Cooking zone control panel
Cooking zone position indicator.
The cooking zones are able to work in combination, creating a single
zone with the same power level. Front master and back secondary
cooking zones. To activate the Bridge function: touch simultaneously
the 2 bar and the symbol lights up.
With the selection bar of the master zone it is possible to select the
power level.
To deactivate the bridge function simply repeat the same activation
procedure.
Cooking zone selection.
Increase/Decrease power level.
Supplementary power feature which remains active for 10 minutes,
after which the temperature returns to the level 9.
Touch and scroll along the Selection bar and activate the Power
Booster.
The power booster level is shown on the display of the selected zone
with the symbol .
Temperature Manager activation. The display shows .
Melting at 42°C
Keep Warm at 74°C
Slow Cooking at 92°C
Bridge zone between two cooking zones activated.
Power Booster activated.

16 ENGLISH
Extractor control panel
Extractor fan selection
Increase/Decrease extraction speed (power)
Activation/Deactivation of automatic function (by default auto-
matic mode is active).
When the selection bar of the cooker hood is touched (pres-
sed), the automatic mode deactivates and works with the
extractor fan in manual mode.
To re-activate the automatic mode press button and the
led will light up to indicate that the hood is working in
this mode.
 
mode).
Activate charcoal lter reminder
Press for 5 sec the button 
it is switched on, the symbol 
  and the symbol

Since that time the lit icon will show when it is necessary to
  .
    is always
enabled.
Resetting activated carbon odour lter saturation

press and hold 5 sec the button - The grease led will turn
   
press and hold 5 sec the button - The odour led will turn
   
Set the speed BOOST
This speed is timed to run for 5 minutes. At the end of this
time, the system returns automatically to the speed that was
set before.

17 ENGLISH
Cookware guidance
What pots to use
Only use pots and pans with bottom made
from ferromagnetic material which are
suitable for use with inductions hobs:
• cast iron
• enamelled steel
• carbon steel
• stainless steel (although not all)
• aluminium with ferromagnetic coating or
ferromagnetic plate
To determine if a pot or pan is suitable,
check for the symbol (usually stamped on
the bottom). You can also hold a magnet to
the bottom. If it clings to the underside, the
cookware will work on an induction hob.
To ensure optimum efficiency, always
use pots and pans with a flat bottom that
distributes the heat evenly. If the bottom
is uneven, this will affect power and heat
conduction.
How to use
Minimum diameter of pot/pan base for the
different cooking areas
To ensure that the hob functions properly,
the pot must cover one or more of the
reference points indicated on the surface of
the hob, and must be of a suitable minimum
diameter.
Always use the cooking area that best
corresponds to the diameter of the bottom
of the pan.
Empty or thin-based pots/pans
Do not use empty or thin-based pots/pans
on the hob as it will not be able to monitor
the temperature or turn off automatically if
the temperature is too high, damaging the
pan or the hob surface. If this occurs, do not
touch anything and wait for all components
to cool down.
If an error message appears, refer to
“Troubleshooting”.
Cooking
zone
Cookware diameter
[mm]
Ø Min.
(recommended)
Ø Max.
(recommended)
All 145 mm 180 mm
Hint/tips
Noise during cooking
When a cooking area is active, it may hum
briefly. This is a characteristic of all ceramic
glass cooking areas and does not impair the
function or life of the appliance. The noise
depends on the cookware used. If it causes
considerable disturbance, it may help to
change the cookware.

18 ENGLISH
Power
level Cooking method Use for
1 Melting, gentle warming Butter, chocolate, gelatine, sauces
2 Melting, gentle warming Butter, chocolate, gelatine, sauces
3 Swelling Rice
4 Continued cooking, reducing, stewing 
5 Continued cooking, reducing, stewing 
6 Continued cooking, braising Pasta, soup, braised meat
7 Gentle frying Rosti (hash brown), omelettes, breaded
fried foods, sausages
8 Frying, deep frying Meat, chips
9 Flash frying Steak
P Fast heating Boiling water
Temp. level Cooking method Use for
Melting Melting butter, chocolate or honey at around 42°C
Keep Warm Sauces, keep food ready for serving at around 74°C
Slow cooking Keep ready-cooked food warm at around 92°C
Switching the appliance on
Hold for one second to switch on the
appliance.
- „0“
- If there are no further inputs, the appliance

reasons.
Selecting a cooking zone
Press the „0“ near the bargraph slider of the
cooking zone and swipe it to set the power level.
Switchingacookingzoneo
Touch „0“ on the bargraph.
- If there is no further input and the other


Switchingthehobo
Touch 
- If there is no further input on the display and


Daily use

19 ENGLISH
Melting, Keep warm and Slow cooking setting
With the melting function you can defrost food or
gently melt butter, chocolate or honey.
The keep warm setting keeps ready-cooked foods
warm at approx. 74 °C.
The slow cooking setting keeps ready-cooked
foods warm at approx. 92 °C. With the slow
cooking setting you can cook at low temperatures
to preserve the nutritional value of the aliments.
- Select the cooking zone by pressing „0“ near
the bargraph of the cooking zone.
- Press one time.
- To select the setting for „Melting“ (defrosting),
press one more time.
appears.
- To select the setting for „Keep warm“, press
one more time.
appears.
- To select the setting for„Slow cooking“, press
one more time.
appears.
Boost setting
All the cooking zones are equipped with the
booster.
When Booster is switched on, the cooking zone
selected works at extra high power for 5 minutes.
Booster can be used, for instance, to quickly heat
a large quantity of water.
- Swipe up on bargraph until a appears in
the display.
- To end Booster swipe down on the bargraph to
the desired power level.
Timer

after a set time between 1 min and 1 h 59 min.
Setting the timer
- Hob switched on.
- Cooking zone set.
- Press .
- „_00“ show in the middle of the display.
- Touch to increase the timer duration, touch
to reduce the time.
When you press „1“ is
illuminated in the display.
Changing the timer
-Timer set
- Press the active cooking zone of the timer that
you want to change.
-Press .
-Change the timer duration using and .
Bridging function
The bridging function allows two individual
cooking zones to be switched on to be adjusted
together.
-Press at the same time the bargraphs of the two
cooking zone (same side).
-The display near the two zones shows on one
side and on the other side.
If one of the cooking zones is already running
when the bridging function is switched on, the
power level and operating time of this cooking
zone will be used for both zones. If both cooking
zones are already running, the operating times
are cleared in the power level displays.
In the Bridging function is not possible set the
Boost speed.
Child proof lock
- Appliance switched on
- Touch and simultaneously for few seconds
until an acoustic signal is emitted.
The display is locked. When the display

still be active once you restart the hob.
- To deactivate the childproof lock, press and
simultaneously for a few seconds.

20 ENGLISH
Troubleshooting
If there is a fault try to solve the problem by
following the troubleshooting guidelines. If the
problem cannot be solved contact After Sales
Service. You can find a full list of IKEA
appointed contacts at the end of this user
manual.
If you operate the appliance wrongly, or the
installation was not carried out by an
authorised installer, the visit from the After
Sales Service technician or dealer will not be
free of charge, even during the warranty
period.
Error code Description Possible cause of error Remedy
No Function Wrong connection to the mains
or shortcircuit
Disconnect the hob extractor from
the power supply.
Adjust the power supply
connection according to
“ELECTRICAL CONNECTION“
paragraph if needed.
If error persists, please contact
After Sales Service and specify the
problem.
ER 03 and
continuous
tone or
Control panel turns

Continuous sensor activation
detected. Water or cookware on
the glass over the control panel.
Remove water or cookware from
glass and control panel.

ER 03 and
continuous
tone
Extractor
control panel
Control panel turns

Extractor motor is
still on.
Continuous sensor activation
detected. Water or cookware on
the glass over control panel of
the extractor.
Remove water or cookware from
glass and control panel.
Touch again the control panel of
the extractor.
ER20
ER22
ER30
ER36
ER39
ER47
U400
E/2
E/A
E/4
E/6
E/7
E/8
E/9
Disconnect the hob extractor from the power supply.
Wait a few seconds then reconnect the hob extractor to the power supply.
If the problem persists, call After Sales Service and specify the error code that appears on
the display.