Ikelite 9304.53 User manual

9304.53 Flat Port
Instruction Manual
Thank you for your purchase of Ikelite equipment. Please read this
instruction manual completely before attempting to operate or dive
with this product. Please refer to the back page of this manual to
register your Ikelite product.

2
No tools are needed to remove the Dome Port and attach the optional
Flat Port for the Canon EF-S 60mm Macro lens, Diagram A.
1. Three Thumb Screws secure the Port on the Base. Turn each Thumb
Screw counterclockwise so at least 3 to 4 threads are showing.
2. Gently lift the Dome Port off the Port Base, Diagram B, Page 3. If the
Port seems stuck, loosen the Thumb Screws another turn or two until
the Port can be removed.
3. REM VE the gear sleeve.
Caution: D N T leave the Port off the Port Base for extended
periods of time. This can result in debris being attracted to the Port Base
-ring, Diagram B, Page 3, resulting in a bad seal.
Removing t e Dome Port
Tighten
Loosen
Diagram A
Approximately 3/32” gap
will be present between
the Housing Front and
bottom of Port when
the Dome or Flat Port is
properly installed. Thumb Screws

Removing t e Dome Port - continued
3
Diagram B
Thumb Screw
Remove Gear Sleeve
Port Base -ring;
should be lightly
lubricated - use
Ikelite lubricant
only.

1. First check to see that there is a thin film of lubricant on the Port Base
-ring. The o-ring should appear slick. If necessary, relubricate with the
supplied Ikelite lubricant. Do not use excessive lubricant which can
attract hair or other debris. Use NLY Ikelite lubricant.
2. Make sure the o-ring is free of hair or other debris.
3. Lift and REM VE the gear sleeve from inside the Port Base. Place the
Gear Sleeve in storage for later use with the Dome Port.
4. Slide the Flat Port over the Port Base until it ST PS, Diagram C, Page
5. When properly installed, there should only be an approximate 3/32”
gap between the bottom of the Port and the front of the housing,
Diagram A, Page 2.
6. Snugly tighten the 3 thumb screws into the Port Base. D N T
overtighten. No Thumb Screw threads will be visible once the Port is
properly secured.
* The gear sleeve must be removed BEF RE using the Flat Port.
* We recommend placing the closed housing in a pool or bathtub to
assure proper installation and watertightness before installing your
camera.
Installing t e Flat Port
4

Installing t e Flat Port - continued
Tighten
Loosen
5
Diagram C
Thumb Screw
Port Base -ring;
should be lightly
lubricated - use
Ikelite lubricant
only.

6
Customer Support
Ikelite Underwater Systems
Service Department
50 West 33rd St.
Indianapolis, IN 46208 USA
Email: [email protected]
Phone: [phone]
This Ikelite product is warranted against any manufacturing defects for a
period of one (1) year from the original date of purchase. Defective
products should be returned to Ikelite postage paid. Ikelite will, at its sole
discretion, repair or replace such products, and will return to customer
postage paid. All other claims of any nature are not covered. Except as
mentioned above, no other warranty expressed or implied applies to this
Ikelite product.
Limited Warranty

For the separate international customs documentation form that you
complete to accompany the shipment, please state or designate that the
enclosed products were originally manufactured in the USA and are
being returned to the manufacturer for repair service. Value of the
equipment listed for customs purposes should be zero.
7
Returning Products for Service - outside t e United States
Ikelite is most interested in performing any service to ensure that all
products perform as intended. Evidence of purchase date must be
provided to obtain warranty service.
No prior authorization is required. You may return directly to us or
through your dealer. Please include a brief description of the problem,
any relevant email correspondence, and/or instructions on what you
want us to do. Always include name, shipping address, email address,
and phone number inside of the package. Send postage paid to:
Ikelite Underwater Systems
Attention: Service Department
50 West 33 Street
Indianapolis, IN 46208 USA
No reimbursements for postage paid will be issued.
You may also want to insure the package.
Returning Products For Service

Ikelite Underwater Systems
50 West 33rd Street
Indianapolis, IN 46208 USA
www.ikelite.com
9304.53_Canon_SL1_Flat_Port_01-0314
© 2014 Ikelite Underwater Systems
Product Registration
Please go to www.ikelite.com to register your Ikelite housing within 15
days of purchase.