iLight SCMS0410 User manual

Mounting & Installation Technical Data
Typical Schematic
Maximum Load: 40 Amp @ 50ºc
Maximum Channel Current: 10 Amp
Load Protection: Provided by installer
Control Supply: 150mA quiescent current. (Recommended: 200mA 15V DC Supply)
Terminal Sizes: Channel screw terminals: 8 x 2.5mm2
iCANnet™ input/output screw terminals: 5 x 1mm2
DALI input screw terminals: 2 x 1.5mm2
Alarm input screw terminals: 3 x 2.5mm2
Installation: Installation must be carried out by a suitably qualied electrician
Load Data:
Load types - this unit is designed to work with most lighting load types. Please consult with the iLight
help desk for guidance on true load calculations. Care should be taken when specifying discharge
lighting sources with power factor capacitors.
4 x 10A relays, 120 – 250V AC +/-10%, 50/60 Hz, Volt free
DC switching - Max 24V DC - 10A
Control: Via iLight network connection or a compatible DALI controller
Recommended Network Cable: iCANnetTM Network Cable
Programming: Via Device Editor software
Weight: 0.25kg
Operating temperature: +2ºC to +50ºC
Max storage temperature: +60ºC
Humidity: +5 to 95% non-condensing
Environmental protection: IP20
SCMS0410
4 Channel x 10 Amp Switching Controller
Doc No: 9850-000821-01
SCMS0410 must be mounted in a suitable enclosure to provide regulatory
protection from electric shock hazard as well as protecting the iCANnet
data network from tampering that could lead to reduced network security.
Ensure selected enclosure provides adequate cooling ventilation.
Fixing to DIN rail
1. Fix top clips over DIN rail.
2. Pull down bottom clip using screwdriver.
3. Close module towards DIN rail.
4. Push up bottom clip to x securely to DIN rail.
Removing from DIN rail
1. Pull down bottom clip with screwdriver.
2. Lift module away from DIN rail.
1
2
3
4
1
2
Control Plate
iCANnet
SCMS0410
Network Sensor Lighting Source
Controller
E&OE. iLight reserve the right to make
changes to the equipment without
prior notice.
© Signify Holding
iLight
Usk House, Lakeside
Llantarnam Park,
Cwmbran,
NP44 3HD, UK
t: [phone]
e: [email protected]
www. iLight.co.uk
EU Authorised Representative
Cooper Lighting Netherlands B.V.
High Tech Campus
HTC 48
Eindhoven
5656 AE
Installation Guide
Dimensions
DATA
STATUS
ALARM
IDENT
IN1 COM IN2
iCANnet Network
+V CAN H SHIELD CAN L 0V
DA DA
DALI
SCMS0410
ALARM
90 mm
60 mm73 mm

9850-000821-01. E&OE.
Status LED
Green LED ashes – device OK
Green LED ashes rapidly – DALI control
Data LED
Red LED ashes when messages sent on network
Alarm LED
Red LED solid on for local initiated alarm
Red LED ashes for network initiated alarm
Device Identication
Press and release switch.
Sending a message to identify the device on the network
(red Data LED ashes)
Device LEDs and Buttons
Typical Connection Diagram
SCMS0410
4 Channel x 10 Amp Switching Controller
230V
N
L
iLight Network
Termination
Connection
to the iLight
Network
Alarm
Input
DALI
Input
Device
Identication
Switch
10A Max
Channel
Indicator
Function iCANnet Cable Colours
0V Black
CAN L Blue
Shield Silver
CAN H White
+VDC Red
Maximum segment distance: 500m (1640 ft)
Devices per segment: 100 (without bridge or repeater)
Consult iLight for information on alternative cable types.
IMPORTANT NOTE: Connecting a mains potential cable to the
iCAN Network terminals is likley to damage the unit and other
devices connected, and invalidate warranty.
iCAN Network Connections
Network Power Requirements
Nominal operating voltage: 15V (12-18V)
Nominal operating current: 150mA
Network termination
The iCAN network follows a daisy chain topology that
requires termination on the devices located at either
end of the network.
The SCMS0410 unit is supplied with termination
disabled as standard. If it is connected as an end
device in the iCAN network, you need to move the
jumper to enable termination.
To enable SCMS0410 termination, move the jumper
outwards from the inner two pins to the outer two pins:
Termination OFF
Termination ON
iCAN
Device
iCAN
Device
SCMS0410