iLight SCD-96-D User manual

Mounting & Installation Technical Data
Typical Schematic
Dimensions
SCD-96-D
96 Channel DMX Source Controller
Doc No: 9850-000857-01
SCD-96-D must be mounted in a suitable enclosure to provide regulatory
protection from electric shock hazard as well as protecting the iCANnet
data network from tampering that could lead to reduced network security.
Ensure selected enclosure provides adequate cooling ventilation.
Fixing to DIN rail
1. Fix top clips over DIN rail.
2. Pull down bottom clip using screwdriver.
3. Close module towards DIN rail.
4. Push up bottom clip to x securely to DIN rail.
Removing from DIN rail
1. Pull down bottom clip with screwdriver.
2. Lift module away from DIN rail.
1
2
3
4
1
2
Control Plate
iCANnet
SCD-96-D
Network Sensor
Electrical Data
Supply: 15VDC (12-18V) via iCANnetTM
Network termination: Screw terminals within two part connectors
Load Types: DMX controlled loads (96 DMX addresses total)
32 connected devices maximum, for more devices utilise DMX Splitter/Repeater or employ multiple SCD-96-Ds
Terminal Sizes:
iCANnetTM network cable size: 5 x 1mm²
DMX output: 3 x 1mm²
Alarm Input: 2 x 1mm2
Memory: FLASH memory to be able to upgrade software
EEPROM for 128 scene memory
Fade Times: 0.1 seconds to 60 minutes
Control Connection:
iCANnetTM network x 2 (Suitable for iCANnet Cable)
CAN termination link
DMX terminals (DMX-512A)
DMX termination link
Alarm input x 1
Mechanical Data
Weight: 0.1 kg (0.22lb)
Operating temperature: 0ºC to +50ºC
Max storage temperature: +60ºC
Humidity: +5 to 95% non-condensing
Environmental protection: IP20
Lighting Source
Controller
E&OE. iLight reserve the right to make
changes to the equipment without
prior notice.
© Signify Holding
iLight
Usk House, Lakeside
Llantarnam Park,
Cwmbran,
NP44 3HD, UK
t: [phone]
e: [email protected]
www. iLight.co.uk
EU Authorised Representative
Cooper Lighting Netherlands B.V.
High Tech Campus
HTC 48
Eindhoven
5656 AE
Installation Guide

9850-000857-01. E&OE.
Data LED
Red ashing: Trac being sent and/or received
Red on: iCAN network comms error
Status LED
Green ashing: Normal operation
DMX LED
Red ashing: DMX data sent
Alarm LED
Red ashing: Alarm data sent
Device Identication Button (IDENT)
Press and release switch.
Sending a message to identify the device on the network
(red Data LED ashes).
Device LEDs and Buttons Typical Connection Diagram
SCD-96-D
96 Channel DMX Source Controller
Data LED
Status LED
DMX LED
Alarm LED
Network termination
The iCAN network follows a daisy chain topology that
requires termination on the devices located at either
end of the network.
The SCD-96-D unit is supplied with termination
disabled as standard. If it is connected as an end
device in the iCAN network, you need to move the
jumper to enable termination.
To enable SCD-96-D termination, move the jumper
outwards from the inner two pins to the outer two pins:
Termination OFF
Termination ON
iLight Network Termination
Device Identication Button
Alarm InputDMX Output
Connection to the iLight Network
iCAN
Device
iCAN
Device
SCD-96-D
iCAN network wiring
Cable connections to the iCAN network are made to a removable
5-way connector block located at one end of the SCD-96-D unit:
Function iCANnet Cable Colours
0V Black
CAN L Blue
Shield Silver
CAN H White
+VDC Red
+VDC CAN-H SHIELD CAN-L 0V
Network Power Requirements
Nominal operating voltage: 15V (12-18V)
Nominal operating current: 70mA
Maximum segment distance: 500m (1640 ft)
Devices per segment: 100 (without bridge or repeater)
Additional power supplies may be required.
Consult iLight for information on alternative cable types.
IMPORTANT NOTE: Connecting a mains potential cable to the
iCAN Network terminals is likley to damage the unit and other
devices connected, and invalidate warranty.