iLiving ILG8M24-70EC User manual

1
24” BRUSHLESS DC DRUM FAN
MODEL: ILG8M24-70EC
115V 60Hz 0.22HP
24” continuous variable
speed adjustment
Owner’s Manual
PLEASE READ AND
SAVE THESE INSTRUCTIONS

2
TABLE OF CONTENTS
Important Instructions………………………………………. 3
Specifications and Wiring Diagram………………………. 5
Parts of the FAN ……………………….………………… 6
Installation Instructions……………………….…………..… 6-7
Operating Instructions……………………….………....… 8
Maintenance and Cleaning………………………………. 9
Troubleshooting……………………………………………. 10

3
IMPORTANT INSTRUCTIONS
CAUTION: Please read and save these instructions. Read carefully before attempting
to assemble, install, operate or maintain the product described. Do not use the fan if
any part is damaged or missing. Automatic reset safety device in motor. To reduce
risk of injury disconnect power supply before servicing.
Protect yourself and others by observing all safety information. Failure to comply
with instructions could result in personal injury and/or property damage!
Retain instructions for future reference.
WARNING: To reduce the risk of electric shock, do not
expose the fan to water or rain. To reduce the risk of fire
or electric shock, do not use this fan with any solid state
speed control device. This appliance has a grounded plug.
To reduce the risk of fire or electric shock, this plug is
intended to fit in an outlet only one way. If the plug does
not fit into the outlet, contact a qualified electrician. Do not attempt to bypass this
safety feature.
General Safety Information
NOTE: To comply with UL507, air circulator is not to be used in
unattended areas.
1. Ensure that the power source conforms to the electrical requirements of the fan.
2. Where a two-prong wall receptacle is encountered, it must be replaced with a
properly grounded three prong receptacle installed in accordance with the United
States National Electrical Code (NEC) and all applicable local codes and ordinances.
This work must be done by a qualified electrician, using copper wire only.
3. Where possible, avoid the use of extension cords. If they must be used, minimize
the risk of overheating by ensuring that they are UL Listed and of the proper gauge
and length. Never use a single extension cord to operate more than one fan.
4. Do not kink the cord or allow it to contact oil, grease, chemicals, hot surfaces, or
sharp or abrasive objects.
5. This fan is to be operated ONLY with its OSHA compliant guards in place to prevent
persons and/or objects from contacting the revolving propeller. Any other use voids
warranty and may create unsafe conditions.
6. Fan is intended for general air circulation ONLY. It must NOT be used in potentially
dangerous locations such as flammable, explosive, chemical-laden, or wet

4
atmospheres. Do not use fan in or near a window, since rain may create an electrical
hazard. Do not attach ductwork to the fan.
7. Fan motor is equipped with an automatically resetting control circuit that will
disconnect power if the motor overheats. Always unplug fan before removing guard,
as motor may restart unexpectedly.
8. Do not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
similar coverings. Do not route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped over.
10. Disconnect the fan when moving it from one location to another.
11. Make sure the fan is on a stable, flat surface while it is in operation.
12. Disconnect the fan when removing the guards for cleaning.
1. Use of a three-prong to two-prong adapter is not recommended.
Improper connection may create the risk of electrocution. Use of such
adapters is prohibited in Canada.
2. Do not depend on any switch as the sole means of disconnecting
power when installing or servicing the fan. Failure to do so may result in
fatal electrical shock.
3. Do not insert fingers or foreign objects into the fan. Do not block or
tamper with the fan in any manner while it is in operation.
4. Do not touch motor. May be hot enough to cause injury.
5. Unplug prior to servicing unit.
6. To reduce the risk of fire or electric shock, do not use this fan with any
speed control device.
SAVE THESE INSTRUCTIONS

5
SPECIFICATION AND WIRING DIAGRM
Model: ILG8M24-70EC
115V 60Hz 0.22HP
Wiring Diagram: