iLiving ILG8HVLS72 User manual

1
Industrial BLDC Ceiling Fan
Owner’s Manual
Model No.: ILG8HVLS72/ILG8HVLS88/
ILG8HVLS96/ILG8HVLS108
IMPORTANT INSTRUCTIONS
READ & SAVE THESE INSTRUCTIONS

2
TABLE OF CONTENTS
General Safety Instructions………………………………....….......……. 3-4
Specifications ………………………......................... .......................... 4
Parts of the ceiling fan ..............……………………….…….......…....… 5-7
Installation Instructions …………………….............….…….......…....… 8-14
Remote Control & Operating Instructions …………………..……....… 15-17
Maintenance and Cleaning ……………………………....................…. 18
Troubleshooting …………………………………………...................…. 18
Warranty Information ……………………………………...........………. 19

3
Read instructions carefully before assembling or installing your fan. It is important that you
observe all safety information to help prevent personal injury and/or property damage.
1. Installation work and electrical wiring should be done by qualified person only in accordance
with all applicable codes and standards.
2. All wiring and installation procedures must satisfy National Electrical Codes (ANSI/ NFPA 70)
and Local Codes.
3. Disconnect the fan from the power supply before any servicing.
4. Use this fan only in the manner intended by the manufacturer. This fan is intended for
permanent installation and to be used for circulation only.
5. The secondary support cable included with the fan must be properly connected.
6. To reduce the risk of personal injury, do not bend the blade mount when installing the mount
onto the motor, installing the blades onto the mount, or cleaning the fan.
7. Before servicing or cleaning unit, switch power off at service panel and lock service panel
disconnecting means to prevent power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the
service panel.
8. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always turn
off the power to the ceiling fan before servicing.
9. Do not insert foreign objects in between rotating fan blades.
10. Ceiling fans without guards are to be installed at least 10 feet above the floor with adequate
clearance between blades and adjacent walls, furnishings, etc.
11. When mounted in cathedral ceiling, blade tips should be at least 1 foot from the angled roof
line or air turbulence may cause the fan to sway.
12. The supporting beam must be capable of holding at least 90 pounds (or the weight of the fan
plus any accessories that might be added).
13. Suitable for use with solid-state speed controls.
14. For supply connections, if the conductor of a fan is identified as a grounded conductor, then it
should be connected to a grounded conductor power supply. If the conductor of a fan is
identified as an ungrounded conductor, then it should be connected to an ungrounded conductor
power supply. If the conductor of a fan is identified for equipment grounding, then it should be
connected to an equipment grounding conductor.
WARNING: TO REDUCE THE RISK OF SHOCK, THIS FAN MUST BE INSTALLED WITH A GENERAL
USE ISOLATING WALL CONTROL/SWITCH.
15. To reduce the risk of fire or electric shock, do not use this fan with other types of solid-state
speed control devices.
WARNING: To reduce the risk of personal injury, do not bend the blade bracket (flange or blade
holder) when installing the brackets, balancing the blades, or cleaning the fan. Do Not Insert
Foreign Objects In Between Rotating Fan Blades.
WARNING: Chemical Burn Hazard. Keep batteries away from children.
This product contains a battery. If a new or used battery is swallowed or enters the
GENERAL SAFETY INSTRUCTIONS

4
body, it can cause severe internal burns and can lead to death in as little as 2 hours. Always
completely secure the battery compartment. If the battery compartment does not close
securely, stop using the product, remove the batteries, and keep it away from children. If you
think batteries might have been swallowed or placed inside any part of the body, seek
immediate medical attention.
Suitable for Commercial or Industrial Use Only.
Airflow(CFM)
ILG8HVLS72
ILG8HVLS88
ILG8HVLS96
ILG8HVLS108
Speed 6
9,900
13,600
17,000
19,000
Speed 5
8,100
10,700
12,600
14,500
Speed 4
7,100
9,300
9,900
12,800
Speed 3
4,700
7,500
8,100
10,100
Speed 2
3,800
4,800
6,100
9,100
Speed 1
1,200
3,300
5,000
7,800
Specification
Model#
ILG8HVLS72
ILG8HVLS88
ILG8HVLS96
ILG8HVLS108
Size(inch)
72"
88"
96"
108"
Voltage(V)
120
120
120
120
Frequency(Hz)
60
60
60
60
Wattage(W)
47.5
47.5
47.5
48
RPM
146
104
90
78
AMPS
0.68
0.68
0.68
0.7
Downrod
Dimensions(inch)
φ1-1/32x6”
φ1-1/32x6”
φ1-1/32x6”
φ1-1/32x6”
Blade Pitch
4°
4°
4°
4°
Speeds
6
6
6
6
Net Weight(lbs)
21.5
23.5
24.5
26.4
Certification
UL, cUL
UL, cUL
UL, cUL
UL, cUL

5
REF
QTY
DESCRIPTION
SP-HVLS-1
1
Mounting Bracket
SP-HVLS-2
1
Downrod/Ball Joint Assembly
SP-HVLS-3
1
Canopy
SP-HVLS-4
1
Canopy Cover
SP-HVLS-5
1
Downrod Cover
SP-HVLSxxx-6
1
Motor Assembly
SP-HVLS-7
1
Fan Blade Holder
SP-HVLSxxx-8
9
Fan Blade
SP-HVLS-9
9
Fan Blade Cap
SP-HVLS-10
9
Fan Blade Screw Cover
SP-HVLS-11
1
Bottom Cover
PARTS OF THE CEILING FAN
SP-HVLS-1
SP-HVLS-2
SP-HVLS-3
SP-HVLS-4
SP-HVLS-5
SP-HVLSxxx-6
SP-HVLSxxx-8
SP-HVLS-9
SP-HVLS-10
SP-HVLS-11
SP-HVLS-7
Note: xxx = Fan Blade size, 72, 88, 96, 108

6
REF
QTY
DESCRIPTION
H1
2
10# 32x3/4 SCREW
H2
3
WIRE CAPS
H3
1
3/16 * 2 INCH WOOD SCREW
+Ф5.5xФ25xT1.5 LOCK WASHER
(For cUL only)
H4
1
MOUNTING PIN
H5
28
M5x10mm LONG SCREW
H6
1
COTTER PIN
H7
7
1/4-20x5/16”LONG SCREW
H8
7
Ф6 LOCK WASHER
H9
10
M4x6mm LONG SCREW
H10
10
Ф4 PLAIN WASHER
H11
38
Ф5 LOCK WASHER
H12
10
M5x8mm LONG SCREW
H13
1
REMOTE AND REMOTE BRACKET
H14
1
BATTERY
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14

7
Dimensions (inch)
Model#
D
H
ILG8HVLS72
72
16-3/4
ILG8HVLS88
88
16-3/4
ILG8HVLS96
96
16-3/4
ILG8HVLS108
108
14

8
WARNING
To avoid possible electrical shock, be sure electricity is
turned off at the main fuse box before hanging. (Figure 1)
NOTE: If you are not sure if the outlet box is grounded,
contact a licensed electrician for advice, as it must be
grounded for safe operation.
WARNING
The fan must be hung with at least 10´of clearance from
floor to blades. (Figure 2)
WARNING
The outlet box must be securely anchored and capable
of withstanding a load of at least 35 lbs. Hanger bracket
must seat firmly against outlet box.
If the outlet box is recessed, remove wallboard until
bracket contacts box. If bracket and/or outlet box are
not securely attached, the fan could wobble or fall.
The fan be mounted to an outlet box and that the
mounting screws provided with the outlet box shall be
used.
WARNING
To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box
Marked " Acceptable for Fan Support of 15.9 kg (35 lbs) or less" And Use Mounting
Screws Provided With The Outlet Box.
WARNING
To Reduce The Risk Of Electric Shock, This Fan Must Be Installed With An Isolating
Wall Control Switch.
INSTALLATION INSTRUCTIONS

9
Before installation, check that the outlet box is securely installed in place and it is able to support
at least the fan weight. Securely attach the mount bracket to ceiling outlet box acceptable for
ceiling fan support.
Attention
Install the ceiling fan in a location such that the spacing from the tip of the blades to the nearest
objects or walls is AT LEAST 12” (300mm).
If the ceiling is angled, the fan mounting equipment is only designed for a maximum 11 degree
incline or decline.
Install the fan blade holder to the motor assembly with (H8) Ф6 lock washers and
(H7)1/4-20x3/8”long screws.
Leveled Ceiling
Mounting
Angled Ceiling
Mounting

10
Install the fan assembly to the mount bracket as shown below:
Remove the two set screws from the downrod and retain for reinstallation. Install the(H4)
mounting pin by aligning the holes in the downrod support with holes in the downrod. Secure pin
with (H6) cotter pin. Install and tighten the two set screws with nuts in the downrod support.
WARNING
It is critical that the mounting pin in the downrod support is properly installed and the set screws and
nuts are securely tightened. Failure to do so could result in the fan falling.
Route wires and safety cable through
downrod cover, canopy cover and ceiling
canopy. Install the downrod with motor
assembly through the canopy, canopy
cover and downrod cover.
Installed in
the part
already

11
Install the fan assembly to the mount bracket as shown below.
Rotate till notch on the ball joint
catches the stopper on the mounting bracket.

12
Connect wires to supply/grounding wires using connectors as shown below. Attach the safety cable
with (H3) 3/16 * 1-1/2 inch wood screw +Ф5.5xФ25xT1.5 lock washer to the ceiling .
Conductor of a fan identified as grounded conductor to be connected to a grounded conductor of
power supply, conductor of fan identified for equipment grounding to be connected to an
equipment-grounding conductor.
After making the wire connections, the wire should be spread apart with the grounded conductor
(neutral Wire) and the equipment-grounding conductor (Ground Wire) on one side of the outlet box and
the ungrounded conductor (Live Wire) on the other side of the outlet box.
The splices after being made should be turned upward and pushed carefully up into the oulet box.
Warning
1. This appliance must be grounded.
2. This product must be installed by a certified electrician in accordance with local codes.
3. Check to see that all connections are tight, including ground, and that no bare wire is
visible at the wire connectors. Do not operate fan until the blades are in place. Noise and
motor damage could result.
For cUL only

13
Remove the two screws from the mount bracket. Assemble the canopy by tighten the screws.
Securely attach and tighten the canopy cover.
Rotate canopy until
lock pin of mounting
bracket is engaged
with canopy, then
tighten the screws
till the keyhole is
locked.
Install the fan blade cap to the
fan blade with (H9) M4x6mm
long screw and (H10) Ф4 plain
washer. Repeat this step for all 9
fan blades.
Install the fan blade screw cover to
the fan blade with (H12) M5x8mm
long screw and (H11) Ф5 lock
washer. Repeat this step for all 9 fan
blades.

14
Rotate the bottom cover to the fan assembly until tighten.
Assemble the fan blade to the fan
blade holder with (H5) M5x10mm
long screw and (H11) Ф5 lock
washer. Repeat this step for all 9
fan blades.

15
HOW TO INSERT BATTERY
NOTE: Remove the batteries if the remote control is not to be used for a month or more.
Batteries left in the unit may leak and cause damage.
Button
Description
Power ON/Off
1
Speed 1 (Minimum)
2
Speed 2
3
Speed 3
4
Speed 4
5
Speed 5
6
Speed 6 (Maximum)
Direction Control
(Clockwise/Counterclockwise）
2H 4H 8H
Timer Setting
REMOTE CONTROL & OPERATION

16
REMOTE CONTROL OPERATION INSTRUCTIONS
(1) After the ceiling fan has been installed according to the assembly procedure and
connected according to power supply specifications, perform the remote control
and ceiling fan pairing procedure (refer to the remote control pairing method
below).
(2) After the pairing has been completed, you can use the remote control to turn
on/off the ceiling fan, and select speed.
OPERATING INSTRUCTIONS
Remote control pairing procedure:
1. Pairing instructions
(1) Apply power to the fan, within 30 seconds after applying power press the
(Power On/Off) button on the remote until response by a "Beep" Sound. Which
means pairing is successfully and remote will be able to control the fan.
Note: Pairing mode will not work after 30 seconds of applying supply power for . During the
pairing process, pressing any buttons will have no effect. Normal operation resumes after the
pairing process has been complete.
(2) When the remote cannot control the fan, please check the battery switch touching
normally or not, correction of the positive and negative, full or empty of the power.
(3) When the remote cannot control the fan, please check is there any existence of similar
remote controlled products nearby, then check whether they works, because remote
controlled product with the same frequency will disturb each other.
(4) Low voltage of battery will affect the sensitivity of the emitter and the signal reception
accordingly (the indicated light will flash out its warning when the battery get low
voltage), must replace if the battery is getting low voltage.
2. After successful pairing
The fan will operate normally and can be controlled with the remote control. For any
setting on the remote, the fan will response by a "Beep" Sound.
Remote controller can pair with multiple Fans as many as you wanted. But the Fans can
memorize the last two remote controller paired with them only.
3. Memory function
This fan has a speed memory function in case of power outages. If the fan operates at
maximum speed when it shuts off in a power outage, it will resume its operation at the
maximum speed when the power comes back on. The memory function registers the
last operating speed.
4. In case of blade replacement
Repeat steps from section 1 above (pairing procedure) after replacing the fan blades.

17
5. Direction control
Press the Direction Control can change the fan
blade rotate direction.
When the fan blade rotates clockwise (Summer
Mode) and the air will blow down.
A downward air flow creates a cooling effect.This
allows you to set your air conditioner on a higher
temperature setting without affecting your comfort.
When the fan blade rotates counterclockwise
(Winter Mode) and the air will blow up.
An upward airflow moves warm air off the
ceiling area. This allows you to set your heating unit on a
lower setting without affecting your comfort.
6.Setting the Timer
Press the button to set the timer. When the time runs
out, the heater will turn off automatically.

18
1. Because of the fan’s natural movement, some connections and screws may become loose.
Check the support connections, brackets, and blade attachments at least twice a year to make
sure they are secure.
2. Clean the fan periodically to help maintain the appearance. Do not use water when cleaning.
This could damage the motor, or possibly cause electric shock.
3. Use only a soft brush or lint-free cloth to avoid scratching the finish.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly,
installation, or wiring. In some cases, these installation errors may be mistaken for defects.
If you experience any problems, please check the following trouble shooting guide. If a solution
to the problem cannot be found, please consult with a licensed electrician. Do not attempt any
electrical repairs by yourself. For your own safety, turn off power at fuse box or circuit breaker
before trouble shooting your fan.
Trouble
Suggested Remedy
Fan does not start
1. Check main and branch circuit fuses or circuit breakers.
2. Check wire connections as performed in Step #2 of installation.
Caution: Make sure main power is turned off！
3. If the fan still will not start, contact a licensed electrician. Do not attempt to
troubleshoot internal electrical connections by yourself.
Fan sounds noisy
1. Check to make sure all screws in the motor housing are snug (not over
tightened).
2. Check to make sure the screws which attach the fan blade mount to the
motor are tight.
3. Some fan motors are sensitive to signals from Solid State Variable Speed
Controls.
4. Allow a “break-in” period of 24 hours. Most noise associated with a new fan
will disappear after this period.
Fan wobbles
The following procedures should eliminate most of the wobble. Check for
wobble after each step.
1. Check that all blades are screwed firmly into the blade mounts.
2. Check that the blades are screwed firmly into the blade mounts.
3. Check that all set screws attaching the motor to the downrod are tight.
4. Make sure that the mounting bracket is tightened securely to the ceiling.
5. If blade wobble is still noticeable, interchanging two adjacent (side by side)
blades can redistribute the weight and possibly result in smoother operation.
MAINTAINANCE
TROUBLESHOOTING

19
Warranty Information
This product comes with a 1-YEAR LIMITED COMPONENT WARRANTY. If your unit
does not appear to be working properly, please contact our service center by calling
1-800-317-1688. Prior to your call, we encourage you to visit our service related
website www.ilivingusa.com for troubleshooting tips and service instructions if
needed.
Register your product at our website:
Or visit iLivingUSA.com/register-product
Feedback
Love it? Help us make the product more for you.
Let us know with a customer review.
Please visit: https://www.amazon.com/review/review-your-purchases#
At iLiving USA, we are committed to bringing top quality products to our customers.
iLIVING USA
860 Mahler Road,
Burlingame, CA 94010
Tel: [phone]
Email: [e-mail]