iLiving ILG8SF10V-ST User manual

1
SHUTTER MOUNTED EXHAUST FAN WITH
THERMOSPEED (TM) CONTROLLER
ILG8SF12V-ST/ILG8SF10V-ST
OWNER'S MANUAL
PLEASE READ AND SAVE THESE
INSTRUCTIONS

2
PLEASE READ AND SAVE THESE INSTRUCTIONS. READ CAREFULLY BEFORE
ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THE PRODUCT
DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR
FUTURE REFERENCE.
T
BEFORE YOU BEGIN
WARNING!
Installation, trouble shooting, and replacement of parts are to be performed
only by authorized service technicians.
Electrical Requirements:
• The motor amperage and voltage ratings must be checked for
compatibility to supply voltage prior to final electrical connection. Please
refer to the motor's nameplate label.
• Wiring must conform to local, state, and national codes.
Tools / Materials Needed:(Not Included)
• Mounting Fasteners (8)
• Sealant or Caulk
• Regular Screwdriver Set
UNPACKING
Contents:
• Shutter Mounted Exhaust Fan
• Fan control (ILG8SFST)
• Owner’s Manual
Inspect:
•
• After unpacking fan, carefully inspect for any damage that may have
occurred during transit. Check for loose, missing, or damaged parts.
• Check all bolts, screws, set-screws, etc. for looseness that may have
occurred during transit. Tighten as needed. Rotate propeller by hand to
ensure it turns freely.
• See General Safety Instructions on page 3, and Cautions and Warnings
as shown.

3
Fans are UL/CUL Listed, Standard 507.
1. Do not depend on any switch as the sole means of disconnecting
power when installing or servicing the fan.
2. Always disconnect, lock-out, and tag-out power source before installing
or servicing. Failure to disconnect power source can result in fire, shock,
or serious injury.
3. Motor will restart without warning after thermal protector trips. Do not
touch operating motor; it may be hot enough to cause injury.
4. Do not place body parts or objects in fan or motor openings while motor
is connected to the power source.
5. All electrical connections should be made by a qualified electrician.
6. These utility exhaust fans are for general purpose exhaust applications
only. Do not use these exhaust fans in an area where corrosive or
explosive materials may be found.
7. Follow all local and state/provincial electrical and safety codes in the
United States and Canada, as well as the National Electrical Code (NEC)
and the Occupational Safety and Health Act (OSHA) in the United States,
and the Canadian Electric Code (CEC) in Canada.
8. Always disconnect power source before working on or near a motor or its
connected load.
9. Protect the power cable from coming in contact with sharp objects.
10. Do not kink or create tight bends in the power cable and never allow the
cable to come in contact with oil, grease, hot surfaces, or chemicals.
11. Make certain that the power source conforms to the requirements of
your specific exhaust fan model. The fan frame and motor must be
electrically grounded to a suitable electrical ground, such as a grounded
water pipe or ground wire system.
12. To reduce the risk of injury to persons, please observe the following:
In the United States, OSHA compliant guards are required when fan is
installed within 7 feet of the floor or working level. In Canada, CSA
compliant guards are required when fan is installed below 2.5 meters
(8.2 feet) above the floor or grade level.
13. Suitable for use with solid-state speed controls.
GENERAL SAFETY INSTRUCTIONS

4
INSTALLATION INSTRUCTION
1. The unit should be securely mounted in a rigid framework.
NOTE: Allowing the fan frame to flex or move will result in excess
vibrations, which may cause possible premature motor, propeller, or
shutter failure.
2. Install any auxiliary components such as thermostats, switches, or speed
controls.
3. Connect power to the motor using an approved wiring method.
Refer to the following wiring diagram.
Fan frame and motor must be securely and adequately grounded
to a suitable electrical ground, such as a ground water pipe or
ground wiring system.
INSTALLATION INSTRUCTIONS
Wiring Diagram
Installation Diagram
Fan Control Model：
ILG8SFST
Shutter Fan Models:
ILG8SF12V-1
ILG8SF10V-1

5
Power source
115V, 60Hz
Mounting Position
Vertical
Frame Material
Galvanized Steel
Shutter Blade Material
Aluminum Alloy
Propeller Material
Aluminum Alloy and Galvanized Steel
Agency Compliance
UL/CUL 507
Dimensions (Inches)
Product Specifications
Model
ILG8SF12V-1
Voltage
115V
Frequency
60Hz
Wattage
65W
AMPS
0.6A
RPM
1650
CFM
960
Suggested
wall opening
(Sq)
13"
GENERAL SPECIFICATIONS

6
Product Specifications
Model
ILG8SF10V-1
Voltage
115V
Frequency
60Hz
Wattage
65W
AMPS
0.6A
RPM
1650
CFM
820
Suggested
wall opening
(Sq)
10 1/2"

7
1. Keep the area free of objects that could impede air flow on both the
intake and exhaust side of fan.
2. For proper exhaust operation, a window, door, or louver should be
opened for fresh air intake on the opposite side of the area to be
ventilated.
3. Turn the fan ON; the shutter will open automatically. When the unit is
turned OFF, the shutter will close.
4. Speed controllable units are designed to operate at a minimum of fifty
percent line voltage.
1. Disconnect power source before servicing.
2. Periodically clean off accumulated dirt from the propeller, guard, motor,
and shutter.
Do not depend on any switch as the sole means of
disconnecting power when installing or servicing. If power
disconnect is not visible, utilize OSHA Lock out/Tag out procedure.
Failure to do so may result in fatal electrical shock.
Employ proper lock-out/tag-out procedures when performing
maintenance.
OPERATING INSTRUCTIONS
MAINTAINANCE

8
Symptom
Possible Cause(s)
Solution
Excessive noise
Dry motor bearings
Re-lubricate motor
bearings as per instructions
or replace motor.
Loose propeller
Tighten set screws on
propeller hub.
Bent or damaged
propeller
Replace propeller
Loose guard assembly or
motor fasteners.
Tighten as required to 15-
20 lbs. per inch.
Fan inoperative
Blown fuse or open
circuit breaker
Replace fuse or reset
circuit breaker
Defective motor
Replace motor
Switch in OFF position
Turn switch ON
Insufficient air
flow
Blocked intake or
exhaust opening
Clear intake and exhaust
openings of any
obstructions.
Clean motor, guard,
propeller, and shutter
assembly. Increase the
opening of the fresh air
intake.
Low voltage
Check electrical wiring.
Speed control set too low
Increase speed with
controller
TROUBLESHOOTING

9
Warranty Information
Register your product at our website:
Or visit iLivingUSA.com/register-product
Feedback
Love it? Help us make the product more for you.
Let us know with a customer review.
Please visit: https://www.amazon.com/review/review-your-purchases#
At iLiving USA, we are committed to bringing top quality products to our customers.
iLIVING USA
860 Mahler Road,
Burlingame, CA 94010
Tel: [phone]
Email: [email protected]
Like us on Facebook: https://www.facebook.com/ilivingusa/
Follow us on Twitter: @iLIVINGUSA
Check out our website: www.ilivingusa.com