iLiving ILG8W24-51EC User manual

1
WALL / CEILING MOUNT AIR
CIRCULATOR
MODEL: ILG8W24-51EC
115V 60Hz 0.26HP
24” continuous variable
speed adjustment
Owner’s Manual
PLEASE READ AND
SAVE THESE INSTRUCTIONS

2
TABLE OF CONTENTS
Important Instructions………………………………………. 3
Specifications……………………..………………………….. 5
Installing Instructions……………………….…………..… 6-7
Operating Instructions……………………….………....… 8-9
Maintenance and Cleaning………………………………. 10
Troubleshooting……………………………………………. 11

3
IMPORTANT INSTRUCTIONS
CAUTION: Please read and save these instructions. Read carefully before attempting
to assemble, install, operate or maintain the product described. Do not use the fan if
any part is damaged or missing.
Protect yourself and others by observing all safety information. Failure to comply
with instructions could result in personal injury and/or property damage!
Retain instructions for future reference.
WARNING: To reduce the risk of electric shock, do not expose the fan to water or
rain. To reduce the risk of fire or electric shock, do not use this fan with any solid
state speed control device. This appliance has a grounded plug. To reduce the risk of
fire or electric shock, this plug is intended to fit in an outlet only one way. If the plug
does not fit into the outlet, contact a qualified electrician. Do not attempt to bypass
this safety feature.
General Safety Information
NOTE: To comply with UL507, air circulator is not to be used in
unattended areas.
1. Ensure that the power source conforms to the electrical requirements of the fan.
2. Where a two-prong wall receptacle is encountered, it must be replaced with a
properly grounded three prong receptacle installed in accordance with the United
States National Electrical Code (NEC) and all applicable local codes and ordinances.
This work must be done by a qualified electrician, using copper wire only.
3. Where possible, avoid the use of extension cords. If they must be used, minimize
the risk of overheating by ensuring that they are UL Listed and of the proper gauge
and length. Never use a single extension cord to operate more than one fan.
4. Do not kink the cord or allow it to contact oil, grease, chemicals, hot surfaces, or
sharp or abrasive objects.
5. This fan is to be operated ONLY with its OSHA compliant guards in place to prevent
persons and/or objects from contacting the revolving propeller. Any other use voids
warranty and may create unsafe conditions.
6. Fan is intended for general air circulation ONLY. It must NOT be used in potentially
dangerous locations such as flammable, explosive, chemical-laden, or wet
atmospheres. Do not use fan in or near a window, since rain may create an electrical
hazard. Do not attach ductwork to the fan.
7. Fan motor is equipped with an automatically resetting control circuit that will
disconnect power if the motor overheats. Always unplug fan before removing guard,

4
as motor may restart unexpectedly.
8. Do not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
9. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or
similar coverings. Do not route cord under furniture or appliances. Arrange cord
away from traffic area and where it will not be tripped over.
10. Disconnect the fan when moving it from one location to another.
11. Make sure the fan is on a stable, flat surface while it is in operation.
12. Disconnect the fan when removing the guards for cleaning.
WARNING: Use of a three-prong to two-prong adapter is not
recommended. Improper connection may create the risk of electrocution.
Use of such adapters is prohibited in Canada.
WARNING: Do not depend on any switch as the sole means of
disconnecting power when installing or servicing the fan. Failure to do so
may result in fatal electrical shock.
WARNING: Do not insert fingers or foreign objects into the fan. Do not
block or tamper with the fan in any manner while it is in operation.
WARNING: Do not touch motor. May be hot enough to cause injury.
WARNING: Unplug prior to servicing unit.
WARNING: To reduce the risk of fire or electric shock, do not use this fan
with any speed control device.
SAVE THESE INSTRUCTIONS

5
SPECIFICATION
Model: ILG8W24-51EC
115V 60Hz 0.26HP
A: FRONT GRILLE
B: PROPELLER
C: NUTS & WASHER FOR REAR GRILLE
D: REAR GRILLE
E: THE EC MOTOR
F: INDICATOR
G: PULL CHAIN SWITCH
H: POWER CORD
I: SPEED ADJUSTMENT KNOB
J: SWIVEL BRACKET BOLT
K: NUTS & WASHER FOR SWIVEL BRACKET BOLT
L: SWIVEL BRACKET
M: HEXAGONAL BOLT
N: NUTS & WASHER FOR HEXAGONAL BOLT
O: TRIANGLE BOLT
P: NUTS & WASHER FOR TRIANGLE BOLT
Q: MOUNTING BRACKET
R: MOUNTING SCREWS

6
INSTALLATION INSTRUCTION
Grille/Motor Assembly:
1. Place the motor on a flat level surface with the motor shaft facing up.
2. Unscrew the 4 nuts and washers from the motor. Arrange the rear
guard in its proper position. Secure the rear guard to the motor by
inserting and tightening the 4 nuts and washers to the motor (through
the eyelets on the guard). Apply 32-40 in. lbs. of torque to motor mount
nuts.
3. Insert the propeller into the motor shaft until it reaches a stopping
point and the set screw is in line with the flat groove on the motor shaft.
NOTE: Make sure the propeller’s set screw is facing the motor. You may
need to loosen the set screw at the rear of the blade to slide it onto the
shaft.
Secure propeller on the flat of the motor shaft with the set screw. Apply
90-120 in. lbs. torque to propeller set screw.
CAUTION: Do not alter the angle of the blades.
4. Place front guard on rear guard with decal facing away from propeller.
Position guard hooks between ribs of rear guard. Use a large screw driver
to pry guard hooks into place. When assembled, the guard hooks should
be located between the largest, outermost ring and the second
outermost ring. Make sure that all hooks are engaged before operating
fan.
5. Verify that propeller does not contact the guard set at any point
before connecting fan to power supply.
Mounting Bracket:
1. Mark the drill-hole positions on the wall or ceiling (studding) for the mounting
bracket.
2. Drill the required holes with diameter fit for the anchor provided for
positioning the mounting bracket.
3. Attach the bracket to the wall or ceiling (studding) and secure with mounting

7
screws, or appropriately sized bolts and nuts if attaching to I-beams.
NOTE: Always install the bracket to a minimum of 2 x 4 studding.
Wall Mount
Ceiling Mount
4. Assemble the swivel bracket as shown. The bracket has three holes; be
sure square hole is specified in the illustration.
Assemble the motor to swivel bracket:
1. Position the swivel bracket in the motor yoke and align the pivot hole
with the round hole in the swivel bracket.
2. Insert the larger diameter bolt in the pivot hole and install the lock
nut, finger-tight.
3. Insert the smaller diameter bolt in the slot in the motor yoke (or
support bracket) and square hole in the pivot bracket and install
triangle knob, finger-tight.
4. While holding the motor at the desired angle, tighten the smaller
diameter bolt.
5. Tighten larger bolt to 200-230 in. lbs. and smaller bolt to 150-160 in.
lbs. being careful to maintain the desired position.

8
OPERATION INSTRUCTION
TO ADJUST AIRFLOW UPWARD OR DOWNWARD: Loosen the position knob first and
then loosen the pivot screw. Tilt the motor to the desired angle and then firmly
tighten the pivot screw first and then the position knob.
TO ADJUST AIRFLOW LEFTWARD OR RIGHTWARD: Loosen the swivel bracket bolt
nut a little; turn the motor to leftward or rightward to your desired position; tighten
the bolt nut.
Speed Control:
1. This fan employs the latest technology of EC (electronic commutator)
and electronic control.
2. Switch On the fan by pull chain. Pull the chain down will “click” and
fan is ON. To switch off the fan, pull the chain and “click” will switch
OFF the fan.
3. Speed adjustment is continuously variable from 200 (min) to 1200
(max) rpm via the adjustment knob.
4. Turn the knob in clockwise direction will speed up the fan and vice
verse will slow down the fan until stop.
5. Adjust the fan speed to your desire comfortable rate. Turn the knob
slowly as the fan requires time to speed up or slow down.
You can keep the desire speed when you switch off the fan. The next
time you switch on the fan, as long as the knob is at the previous
position, the fan will rotate at this speed.
CAUTION:
Rotation will always have some natural resonance frequency. This fan has
a wide spread of speed adjustment which may have encounter this
resonance at one or two speeds.
At a speed when resonance occurs, the whole fan will vibrate somewhat

9
vigorously and with shaking noise.
When you notice the fan is vibrating, this may be the resonance. Too
much resonance will damage the fan. Please skip this speed and you will
see the fan ceases vibrating immediately.
Resonance is nature physical phenomenon. Please skip the speed that
will cause the resonance.

10
MAINTENCE AND CLEANING
WARNING:Parts replacement and troubleshooting to be performed only
by qualified personnel.
WARNING:Do not depend on any switch as the sole means of
disconnecting power when installing or servicing the fan. Failure to do so
may result in fatal electrical shock.
WARNING:Unplug the fan from the wall outlet before servicing or
cleaning.
CAUTION: There is no user maintenance part except regular cleaning as
following description. All other servicing or maintenance should be
performed by qualified service personnel.
To clean the fan, use a soft damp cloth. Wipe down with a dry cloth.
Do not use cleaners that are harmful to paints or plastics.
CAUTION: Do not use gasoline, benzene, thinner, harsh cleaners, etc.,
which are dangerous and will damage the air circulator.
The propeller, guard, and motor should be cleaned periodically to
prevent overheating, and/or operating in an imbalanced condition.
CAUTION: If cleaning requires the removal of a guard, remove only the
front guard and re-install when finished in its originally installed position.
Do not repair propeller if it becomes damaged. The propeller is
accurately balanced at the factory and should be replaced if damaged.
Do not bend the blades.
Motor is permanently lubricated.

11
TROUBLE SHOOTING
If your fan fails to operate, please follow these Instructions:
1. Make sure the fan is plugged in and the electrical outlet is working
properly.
2. Check for any obstruction. If you find an obstruction, turn the fan
“OFF”. Unplug the fan and carefully remove the obstruction.
Plug the fan in and turn it on again and see if it resumes normal.
NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR FAN, PLEASE DO NOT
ATTEMP TO OPEN OR REPAIR THE FAN YOURSELF. DOING SO COULD
CAUSE DAMAGE OR PERSONAL INJURY. Always consult the authorized
dealer or certified electrician for further action.
Product Specifications
Model#: ILG8W24-51EC
Voltage: 115V, 60Hz
Current: 3.14 amps;
Power: 250 Watts

12
Warranty Information
Register your product at our website:
Or visit iLivingUSA.com/register-product
Feedback
Love it? Help us make the product more for you.
Let us know with a customer review.
Please visit: https://www.amazon.com/review/review-your-purchases#
At iLiving USA, we are committed to bringing top quality products to our customers.
iLIVING USA
860 Mahler Road,
Burlingame, CA 94010
Tel: [phone]
Email: [email protected]