iLiving ILG8SF10V-T User manual

1
MULTI-SPEED SHUTTER MOUNTED
EXHAUST FAN WITH THERMOSTAT
Models: ILG8SF10V-T/ILG8SF12V-T/ILG8SF14V-T/
ILG8SF16V-T/ILG8SF18V-T/ILG8SF20V-T/
ILG8SF24V-T/ILG8SF30V-T
OWNER'S MANUAL
PLEASE READ AND SAVE THESE
INSTRUCTIONS

2
PLEASE READ AND SAVE THESE INSTRUCTIONS. READ CAREFULLY BEFORE
ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THE PRODUCT
DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY
INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN
PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR
FUTURE REFERENCE.
T
BEFORE YOU BEGIN
WARNING!
Installation, trouble shooting, and replacement of parts are to be performed only
by authorized service technicians.
Electrical Requirements:
• The motor amperage and voltage ratings must be checked for compatibility to
supply voltage prior to final electrical connection. Please refer to the motor's
nameplate label.
• Wiring must conform to local, state, and national codes.
Tools / Materials Needed（Not Included）:
• Mounting Fasteners (8)
• Sealant or Caulk
• Regular Screwdriver Set
U
UNPACKING
Contents:
• Shutter Mounted Exhaust Fan
• Owner’s Manual
Inspect:
•
• After unpacking fan, carefully inspect for any damage that may have occurred
during transit. Check for loose, missing, or damaged parts.
• Check all bolts, screws, set-screws, etc. for looseness that may have occurred
during transit. Tighten as needed. Rotate propeller by hand to ensure it turns
freely.
• See Important Safety Instructions on page 3, and Cautions and Warnings as
shown.

3
Fans are UL/CUL Listed, Standard 507.
1. Do not depend on any switch as the sole means of disconnecting power when installing or
servicing the fan.
2. Always disconnect, lock-out, and tag-out power source before installing or servicing.
Failure to disconnect power source can result in fire, shock, or serious injury.
3. Motor will restart without warning after thermal protector trips. Do not touch operating
motor; it may be hot enough to cause injury.
4. Do not place body parts or objects in fan or motor openings while motor is connected to
the power source.
5. All electrical connections should be made by a qualified electrician.
6. CAUTION - For General Ventilating Use Only. Do Not Use To Exhaust
Hazardous Or Explosive Materials And Vapors.
7. Follow all local and state/provincial electrical and safety codes in the United States and
Canada, as well as the National Electrical Code (NEC) and the Occupational Safety and
Health Act (OSHA) in the United States, and the Canadian Electric Code (CEC) in Canada.
8. Always disconnect power source before working on or near a motor or its connected load.
9. Protect the power cable from coming in contact with sharp objects.
10. Do not kink or create tight bends in the power cable and never allow the cable to come in
contact with oil, grease, hot surfaces, or chemicals.
11. Make certain that the power source conforms to the requirements of your specific exhaust
fan model. The fan frame and motor must be electrically grounded to a suitable electrical
ground, such as a grounded water pipe or ground wire system.
12. Do not operate any fan with a damaged cord or plug. Discard fan or return to an
authorized service facility for examination and/or repair.
13. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and similar danger locations.
14. The discharge air is to be directed to the building exterior.
15. Questions? Please contact our service center by calling 1-650-952-2257.
Thermal Protection.
INSTALL IN INTERIOR WALL.
CAUTION - MOUNT WITH THE LOWEST MOVING PARTS AT LEAST 2.5 m
(8.2 ft) ABOVE FLOOR OR GRADELEVEL.
CAUTION: HOT SURFACE. AVOID CONTACT.
WARNING - For indoor use only.
WARNING - To reduce the risk of electric shock, do not expose to water or rain.
WARNING-To Reduce The Risk Of Fire Or Electric Shock, Do Not Use This Fan
With Any Solid-State Speed Control Device.
Suitable for commercial or industrial use only.
IMPORTANT SAFETY INSTRUCTIONS

4
INSTALLATION INSTRUCTION
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If you have
questions, contact the manufacturer.
b) Before servicing or cleaning unit, switch power off at service panel and lock
the service disconnecting means to prevent power from being switched on
accidentally. When the service disconnecting means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the service panel.
c) Installation work and electrical wiring must be done by qualified person(s) in
accordance with all applicable codes and standards, including fire-rated
construction.
d) Sufficient air is needed for proper combustion and exhausting of gases
through the flue (chimney) of fuel burning equipment to prevent back drafting.
Follow the heating equipment manufacturer’s guideline and safety standards
such as those published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air Conditioning
Engineers (ASHRAE), and the local code authorities.
e) When cutting or drilling into wall or ceiling, do not damage electrical wiring
and other hidden utilities.
1. The unit should be only securely mounted on the wooden plank.
NOTE: Allowing the fan frame to flex or move will result in excess vibrations,
which may cause possible premature motor, propeller, or shutter failure.
2. Install the shutter fan through 8 holes with screws. (Screws are not
included.)
INSTALLATION INSTRUCTIONS
Screws
Install on wooden plank.
8 holes

5
3. Please ensure the space has a gap for enough air to get into the space.
The fan installed on free space of at least 100mm above the upper edges
of the corner.
WARNING:This fan is recommended to be mounted by a qualified electrician.
Fan frame and motor must be securely and adequately grounded to a
suitable electrical ground, such as a ground water pipe or ground
wiring system.
Minimum
Thickness
Fan Model
Screw Size
Screw Picture
Wooden
Plank
10mm
All Models
3/16“ x 1-1/4“
Air Flow

6
Wiring Diagram
Thermostat Temperature Range: 32˚F~130˚F (0˚C~54˚C)
For ILG8SF10V-T/ILG8SF12V-T/ ILG8SF14V-T
For ILG8SF16V-T

7
For ILG8SF18V-T
For ILG8SF20V-T/ ILG8SF24V-T
For ILG8SF30V-T

8
Power source
115V, 60Hz
Mounting Position
Vertical
Frame Material
Galvanized Steel
Shutter Blade Material
Aluminum Alloy
Propeller Material
Aluminum Alloy and Galvanized Steel
Agency Compliance
UL/CUL 507
Dimensions (Inches)
For ILG8SF10V-T/ ILG8SF12V-T/ ILG8SF14V-T

9
Performance
MODEL
Prop. Dia.
Nom.
HP
Amps
RPM
Bearing Type
CFM
ILG8SF10V-T
10"
1/25
0.56
1520
Sleeve
600
ILG8SF12V-T
12"
1/20
0.60
1610
Sleeve
772
ILG8SF14V-T
14"
1/20
0.61
1590
Sleeve
850
ILG8SF16V-T
16"
1/20
0.83
1580
Ball
1200
ILG8SF18V-T
18"
1/15
0.90
1070
Ball
1736
ILG8SF20V-T
20"
1/4
2.59
1075
Ball
3368
ILG8SF24V-T
24"
1/4
2.65
1050
Ball
4244
ILG8SF30V-T
30"
1/3
3.10
825
Ball
5088
MODEL
Prop.
Dia.
A
B
C
D
E
N
G
F
O
H
J
I
Suggested wall
opening (Sq)
ILG8SF10V-T
10"
13"
13"
4 17/32"
2"
5 7/8"
11 21/32"
10 1/8"
10 1/8"
6"
3 17/32"
9/32"
1/2"
10 1/2"
ILG8SF12V-T
12"
15"
15"
5 3/4"
2"
6 5/32"
13 5/8"
12 1/8"
12 1/8"
8"
3 1/2"
9/32"
1/2"
13"
ILG8SF14V-T
14"
17"
17"
5 3/4"
2"
6 5/16"
15 14/16"
14 1/4"
14 1/4"
10 3/16"
3 17/32"
9/32"
1/2"
15"
ILG8SF16V-T
16"
18 29/32"
18 29/32"
5 3/4"
2"
7 7/8"
17 3/4"
16"
16"
11 29/32"
3 17/32"
9/32"
1/2"
17"
ILG8SF18V-T
18"
21"
21"
5 3/4"
2"
8 3/4"
19 11/16"
18"
18"
14"
3 17/32"
9/32"
1/2"
19"
ILG8SF20V-T
20"
23"
23"
5 3/4"
2"
11"
21 25/32"
20"
20"
16"
3 17/32"
9/32"
1/2"
21"
ILG8SF24V-T
24"
27"
27"
5 3/4"
2"
11"
25 21/32"
24 1/8"
24 1/8"
20 1/32"
3 17/32"
9/32"
1/2"
25"
ILG8SF30V-T
30"
33"
33"
5 3/4"
3"
13 3/32"
31 5/8"
30 1/8"
30 1/8"
26"
3 17/32"
9/32"
1/2"
31"
For ILG8SF16V-T/ ILG8SF18V-T/ ILG8SF20V-T/ ILG8SF24V-T/
ILG8SF30V-T

10
1. Keep the area free of objects that could impede air flow on both the intake
and exhaust side of fan.
2. For proper exhaust operation, a window, door, or louver should be opened for
fresh air intake on the opposite side of the area to be ventilated.
3. Connect power plug to any standard 115-volt AC outlet. Caution: Make sure
the Speed Control is in the OFF position.
4. Use the pull chain switch to select the desired operating speed. The speed
runs as HIGH---MID---LOW--- OFF.
5. Press the Thermostat Switch on, select a thermostat setting. Ambient
temperature is regulated by adjusting the thermostat to a desired position.
To set, allow the unit to operate and cool down the room. When the desired
temperature is reached, turn the control knob just until the fan turns off.
This is your ideal setting. The fan will start automatically when the room
temperature raise above this set point, and will turn off when the set point is
reached.
Thermostat control panel
OPERATING INSTRUCTIONS
A
B
C
For ILG8SF16V-T/ ILG8SF18V-T/
ILG8SF20V-T/ ILG8SF24V-T/
ILG8SF30V-T
For ILG8SF10V-T/ ILG8SF12V-T/
ILG8SF14V-T
A. Thermostat Switch
B. Thermostat Knob
C. Pull Chain

11
1. Disconnect power source before servicing.
2. Periodically clean off accumulated dirt from the propeller, guard, motor, and
shutter.
Do not depend on any switch as the sole means of disconnecting
power when installing or servicing. If power disconnect is not visible,
utilize OSHA Lock out/Tag out procedure.
Failure to do so may result in fatal electrical shock.
Employ proper lock-out/tag-out procedures when performing
maintenance.
Symptom
Possible Cause(s)
Solution
Excessive noise
Loose propeller
Tighten set screws on
propeller hub.
Bent or damaged
propeller
Replace propeller
Loose guard assembly or
motor fasteners.
Tighten as required to 15-
20 lbs. per inch.
Fan inoperative
Blown fuse or open
circuit breaker
Replace fuse or reset
circuit breaker
Defective motor
Replace motor
Switch in OFF position
Turn switch ON
Insufficient air
flow
Blocked intake or
exhaust opening
Clear intake and exhaust
openings of any
obstructions.
Clean motor, guard,
propeller, and shutter
assembly. Increase the
opening of the fresh air
intake.
Low voltage
Check electrical wiring.
Speed control set too low
Increase speed with
controller
TROUBLESHOOTING
MAINTAINANCE

12
Warranty Information
Register your product at our website:
Or visit iLivingUSA.com/register-product
Feedback
Love it? Help us make the product more for you.
Let us know with a customer review.
Please visit: https://www.amazon.com/review/review-your-purchases#
At iLiving USA, we are committed to bringing top quality products to our customers.
iLIVING USA
860 Mahler Road,
Burlingame, CA 94010
Tel: [phone]
Email: [e-mail]
Like us on Facebook: https://www.facebook.com/ilivingusa/
Follow us on Twitter: @iLIVINGUSA
Check out our website: www.ilivingusa.com