iLiving ILG-250 User manual

Misting Kit
Model Number: ILG-250
Owner’s Manual
PLEASE READ AND
SAVE THESE INSTRUCTIONS

2
Important Safety
Information
To reduce the r sk of f re, electr c shock, or personal njury, read all the nstruct ons before
us ng th s dev ce. Th s appl ance s ntended for personal use only. Please consult the
manufacturer for other use such as outdoor or commerc al appl cat ons such as garden ng,
agr cultural etc. The use of components and accessor es other than the ones prov ded n th s
package are not recommended by LIVING and may cause hazards and vo d the warranty .
Warnings descr be ser ous consequences result ng from m suse of th s
product.
Warning!
• Read all nstruct ons before us ng th s m st ng k t.
• Use th s m st ng k t only as descr bed n th s manual. Any other use not recommended
by the manufacturer may cause f re, electr c shock, or njury to persons or damage to
property.
• Th s un t s NOT for ndustr al usage. DO NOT use the un t n factory or workshop
where there’s a h gh level of dust. ALWAYS CONSULT THE MANUFACTURER IF
YOU HAVE QUESTIONS IN USING THE UNIT IN AN OUTDOOR ENVIRONMENT.
• Do not nsert or allow fore gn objects to enter any open ng as th s may cause an
electr c shock, f re or damage to the m st ng k t.
• Do not use on soft and slope surfaces, such as a bed, where stab l ty s not ensured.
K t w ll v brate dur ng operat on; use the k t on flat, hard surfaces only.
• Never locate the k t where t may fall nto a bathtub or other water conta ner as t w ll
cause ser ous electr c shock.
• Do not use k t n areas where gasol ne, pa nt or flammable l qu ds are used or stored.
• Do not let k t run dry w thout water supply.
• When connected d rectly to water faucet, adjust water flow to adequate amount.
Water pressure and water flow rate that are too h gh w ll damage and burst the k t
components. A blow out may cause ser ous damage and danger to person.
• Extreme caut on s necessary when k t s n use. Keep k t away from ch ldren or
person w th phys cal challenges. Never leave the k t unattended when operat ng.
• The socket prov ded allows 120VAC and 5 Amp rat ng. Never over load ng the l m t.
• When there s a leakage of water from the k t, mmed ately cease us ng the k t.

3
Contents:
Assembly the kit
1. Nozzle un t:
Tw st the m st ng nozzle to the nozzle connector by hand n clockw se d rect on, ensure the
nozzle s t ghtly secure but not over tw sted.
2. The m st ng r ng:
Use the [1/4” m st ng r ng tub ng long] to l nk up the 6 [nozzle un ts] from 1. Insert the
tub ng nto the nozzle connector’s s de hole. Make sure the tub ng s n l ne w th the hole,
then nsert tube nto connect on hole unt l t stops; may need some strength.
CAUTION! If tube has not been nsert ng properly, leakage may result. To redress the
leakage, tw st and shake the tube, then re- nsert the tube nto the connector.

4
TIPS ! How to remove and re- nsert the tube:
Press down on the [release r ng plate], hold the tube and push nward a l ttle and then
draw t out. Now you can re- nsert the tube aga n for a proper connect on.
Use the [1/4” m st ng r ng tub ng long] to l nk the end s de [nozzle un ts]. Then use the [1/4”
m st ng r ng tub ng short] to connect the end s de of a nozzle un t and the end s de of the T
connector. Now a m st ng r ng has completed.
Insert the [m st ng tube] to the [T connector]
3. You can now put the r ng onto an outdoor fan. Use the cable t e to t e the r ng to the fan’s
front mesh. Fan can use the power socket prov ded by the pump un t or any other
appropr ate wall socket.
CAUTION! The socket only prov des 120VAC 5AMP rat ng. Never overload the socket.
4. Insert the m st ng tube to the [m st outlet connector], refer to page 6, of the pump un t.

5
5. Put the f lter ns de the [tub ng adaptor]. Screw the [tub ng adaptor] to the [water nlet
connector]. Insert the 1/2” tube to the adaptor. Use the hose clamp to secure the tube to
the adaptor.
The other end of the 1/2” tube can be set free nto a water tank or t can be connected
d rectly to a water faucet. Faucet adaptor s not ncluded.
TIPS! A [Calc um Inh b tor F lter] can be connected between the tube and the faucet. It s
a good hab t to always has th s f lter ncluded for qual ty water supply, and to prevent early
clogg ng of the nozzle. The nh b tor f lter s NOT ncluded.
6. Insert the [exhaust tube] to the rel ef valve; a connect on hole s under the rel ef valve. The
rel ef valve s used for dra n ng out a r bubbles from the pump to prevent a r lock
phenomenon.

6
TIPS! The pump tub ng w ll always catch
a r when pump starts draw ng water n. A r
be ng sucked nto the tub ng w ll qu ckly
form bubbles. When bubbles are b g
enough, t w ll block the water flow ns de
the tubes or reduce the pump pressure,
thus weaken ng the m st ng effect.
So, every t me you start the pump, open the rel ef valve and exhaust the [a r/water] stream
for about 15 seconds (or more, depend ng on when the a r/water stream becomes pure
water stream). Then close the valve and start m st ng.
Somehow, the m st ng effect s not perfect; t s because there s st ll a r ns de the tub ng.
Open the valve aga n, exhaust the a r/water stream aga n, and then close valve to see the
m st ng effect. You can repeat th s procedure many t mes to get a f ne m st ng results.
Operation
1. Attach the m st ng r ng to a fan.
2. Place the pump un t n an appropr ate locat on.
3. Insert the m st ng tube nto the [m st outlet connector].
4. Connect the water nlet tube to the [water nlet connector].
5. Drop the water nlet tube nto a water tank or connect t to a faucet.
6. Attach the exhaust tube to the rel ef valve. Open the valve!
7. Plug the pump un t power cord.
8. Power on the pump un t.
9. See water draw from tank nto the pump un t and dra n out from the exhaust tube.
10. Or turn on the faucet and see water dra n out from the exhaust tube.

7
CAUTION! Adjust water flow of the faucet n an appropr ate rate, an adequate amount for
m st ng purpose. Too h gh of a water pressure and water flow rate w ll damage the k t and
burst k t components. A blow out may cause ser ous damage and danger to person.
11. When exhaust tube has a steady flow of pure water stream, close the rel ef valve.
12. Now you can see the m st ng effect.
13. Turn on the fan for more comfort result.
CAUTION!
If a water tank s the water supply source, mon tor the amount of water. Replen sh water when
water level s low. Never let the k t run dry!
SPECI ICATION
Voltage:
110~120VAC 50/60HZ
Pump current: 0.33A
Socket capac ty: 120V 5A
M st ng pressure: 130~200PSI (w th n th s range, the pump s work ng good)
Nozzle: 0.2mm non-dr pp ng type, sta nless steel head
Performance: 2~8 degree temperature drop can be ach eve w th n the m st ng m n env ronment
WARRANTY
Th s M st ng K t comes w th a ONE YEAR LIMITED COMPONENT WARRANTY. If your un t
does not appear to be work ng properly, please contact our serv ce center by call ng
1-800-317-1688. Pr or to your call, we encourage you to v s t our serv ce related webs te
www. l v ngusa.com for troubleshoot ng t ps and poss ble serv ce nstruct ons f needed.
iLIVING USA
Division of TLM International, Inc
860 Mahler Road
Burlingame, CA 94010
Email: [e-mail]
Phone: [phone]