Iluminarc Ilumipod Inground Tri-12 IP User manual

Ilumiline Inground Tri-12 IP
Optic 25 RGB
Quick Reference Guide

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
2
About This
Guide
The
Ilumiline Inground Tri-12 IP Optic 25 RGB Quick Reference Guide
(QRG) only contains the product’s connection and mounting information
, as
well as the menu options and DMX values.
Disclaimer
This QRG does not replace the product’s User Manual. You must download
the corresponding
User Manual from the ILUMINARC® Web site
(
www.iluminarc.com) to learn about the disclaimers, safety notes,
programming modes
, and technical information.
Safety Notes
•
DO NOT open this product unless instructed. It contains no user
serviceable parts.
•
DO NOT look at the light source when this product is on.
•
DO NOT touch the product when it is operating because it may be hot.
•
DO NOT leave any flammable material within 50 cm from this product
while operating or connected to the power outlet to minimize the risk of
fire.
•
This product is for outdoor use and can be submerged (IP67). However,
do not submerge deeper than 1 m for more than thirty (30) minutes.
•
DO NOT operate this product if you see damage on the housing, lenses,
or cables. Have an authorized technician replace the damaged parts.
•
DO NOT connect this product to a dimmer or rheostat.
•
ONLY connect this product to a grounded and protected circuit.
What Is
Included
•
One Ilumiline Inground Tri-12 IP Optic 25 RGB
•
One Power Input Cable (bare-ended)
•
One Data Input/Output Cable (bare-ended)
•
One Installation Sleeve
•
One Pour Kit Cover
•
One Warranty Card
•
One Quick Reference Guide
•The RDM2go, which includes a built in ilumicode addresser along
with many other useful features is now available.
•The Ilumicoode addresser is required for product configuration
(sold separately).

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
3
Features
•1, 3, 4, 6, or 7 channel DMX-512 LED inground wash light
•Operating modes:
1-channel: Dimmer
3-channel: RGB control
4-channel: Dimmer, RGB control
6-channel: RGB control per module (two modules)
7-channel: Dimmer, RGB control, color macros, strobe, dimmer
speed
•Five distinct dimming curves
•IP67 stainless steel gland nuts for cable entry
•Remotely addressable with Ilumicode Addresser
•IP67 ingress protection
•Gore™ valve
•ADA compliant skid resistant, drive over rated glass lens cover
•
High power 3 W (1,050 mA) Tri-color LEDs
Options
•Ilumicode addresser (required for product configuration)
•Ilumicon controller (for operation without DMX controller)

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
4
AC Power
This product has an auto-ranging power supply that works with an input
voltage range of 100~240 VAC, 50/60 Hz.
Power Wiring
You can connect the bare-ended IP67 rated power cable from the product to
an IP67 rated power connector or use an IP67 rated junction box. If using an
IP67 rated junction box, make sure to use IP67 rated conduit.
Power
Cable Table
Connection Wire (US) Wire (Europe) IP67 Pin
AC Live
Black
Brown
1
AC Neutral
White
Blue
2
AC Ground
Green/Yellow
Green/Yellow
3
AC Power Junction
Box Wiring

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
5
DMX
Connection
You can connect the bare-ended IP67 rated signal cable from this product to
two IP67 rated signal connectors (DMX in and DMX Out) or use an IP67
rated junction box. If using an IP67 rated junction box, make sure to use
IP67 rated conduit.
Signal Wiring
To provide a signal for this product, you can connect the bare-ended IP67
rated signal cable from the product to two IP67 rated signal connectors
(DMX in and DMX out) or use an IP67 rated junction box. If using an IP67
rated junction box, make sure to use IP67 rated conduit.
The signal cable must match or exceed the electrical characteristics of
the Belden® 9841 cable for EIA RS-485 applications. You can also use
CAT 5, CAT 5e, or CAT 6.
DMX
Junction
Box Wiring
DMX Cable
Table
Connection DMX In DMX Out IP67 Pin
Ground
Shield
Shield
1
Data -
Black
Green
2
Data +
White
Red
3

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
6
Ilumicon and
DMX
Controllers
The Ilumiline Inground Tri-12 IP Optic 25 RGB can operate with either an
Ilumicon
or a DMX controller. Use the standard DMX connection, as shown
on page 4 (DMX Junction Box Wiring) to connect this product to any of
those controllers. For more information, please refer to the Ilumiline
Inground Tri-12 IP Optic 25 RGB User Manual.
Settings
To configure the Ilumiline Inground Tri-12 IP Optic 25 RGB, use the
Ilumicode addresser
Ilumicode
Connections
The diagram below shows how to connect the Ilumicode to this product.
Note that this connection will control multiple products at the same time, all
having the same DMX address.
To assign individual DMX addresses to each product, you must connect the
Ilumicode unit to each product, individually. You will also have to
disconnect the DMX output of the product being configured if other
products are connected to it.
Ilumicode
Connection
Diagram
ILUMINARC® suggests connecting no more than 20 products in this mode,
keeping the total distance to less than 60 m (197 ft). If not, you may need to
use an optically isolated signal amplifier.

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
7
Installation
Before mounting this product, read the Safety Notes at the beginning of the
Ilumiline Inground Tri-12 IP Optic 25 RGB User Manual and follow the
mounting procedures.
Installation
Diagram
Signal
cable
Power
cable
To signal
distribution box.
To power
distribution box.

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
8
Ilumicode
Control Panel
Description
Button Function
<POWER>
Turns the Ilumicode unit on.
<MENU>
Scrolls through the main level or exits from the current menu
or function.
NOTE: Press and hold to turn the unit off.
<ENTER>
Enables the currently displayed menu or sets the currently
selected value into the selected function.
<UP>
Navigates upwards through the menu options and increases the
numeric value when in a function.
<DOWN>
Navigates downwards through the menu options and decreases
the numeric value when in a function.
Start Address
To ensure full access to all channels in each DMX mode, the highest
recommended DMX addresses are as follows:
Mode Address Mode Address Mode Address
SOLID
512
ARC1+D
509
SPECIAL1
507
ARC1
510
ARC FULL
506

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
9
Menu Options
Main Level
Programming Levels
Description
DMX 001~512 N/A Sets the DMX starting address
PERSON
ARC1
N/A
3-channel: RGB control
ARC1+D
4-channel: RGB control + dimmer
ARC FULL
7-channel: RGB control + dimmer
REMOTE
Allows using the ILUMICON unit
SOLID
1-channel: dimmer
SPECIAL1
6-channel RGB per module
CALIB
WHITE (1~11) RED
GREN
BLUE 0~255
Determines the white balance for
the color macros
RGBTOW
Determines the white balance
when RGBTOW is active
DIMMER
OFF
N/A
Dimmer work in linear mode
DIM 1
Dimmer works in non-linear
mode, from fast to slow.
DIM 2
DIM 3
DIM 4
STATIC
RED
0~255 Configures the static color and
effect
GREN
BLUE
STRB
SETTINGS
COLOR
OFF
Maximum output, unbalanced
white
RGBTOW
White output is as per CALIB >
RGB settings
UC
Output matches that of product’s
previous versions
RESET
NO/YES

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
10
DMX Values
ARC FULL
Channel Function Value Percent/Setting
1
Dimmer
000 ó255
0~100%
2
Red
000 ó255
0~100% (Step Time if CUS 01~10 active)
3
Green
000 ó255
0~100% (Fade Time if CUS 01~10 active)
4
Blue
000 ó255
0~100%
5 Color Macros
000
ó
010
011 ó030
031 ó050
051 ó070
071 ó090
091 ó110
111 ó130
131 ó150
151 ó170
171 ó200
201 ó205
206 ó210
211 ó215
216 ó220
221 ó225
226 ó230
231 ó235
236 ó240
241 ó245
246 ó250
251
ó
255
No function
Red: 100% Green: 0~100% Blue: 0%
Red: 100~0% Green: 100% Blue: 0%
Red: 0% Green: 100% Blue: 0~100%
Red: 0% Green: 100~0% Blue: 100%
Red: 0~100% Green: 0% Blue: 100%
Red: 100% Green: 0% Blue: 100~0%
Red: 100% Green: 0~100% Blue: 0~100%
Red: 100~0% Green: 100~0% Blue: 100%
Red: 100% Green: 100% Blue: 100%
White 1: 3,200 K
White 2: 3,400 K
White 3: 4,200 K
White 4: 4,900 K
White 5: 5,600 K
White 6: 5,900 K
White 7: 6,500 K
White 8: 7,200 K
White 9: 8,000 K
White 8: 8,500 K
White 9: 10,000 K
6 Strobe
000 ó009
010 ó255
No function
0 ~ 20 Hz
7 Dimming Speed
000 ó009
010 ó029
030 ó069
070 ó129
130 ó189
190 ó255
Dimmer is set by Ilumicode
OFF (Dimmer is linear)
DIM1 (Fastest dimmer curve)
DIM2
DIM3
DIM4 (Slowest dimmer curve)
ARC 1
Channel
Function
Value
Percent/Setting
1
Red
000 ó255
0~100%
2
Green
000 ó255
0~100%
3
Blue
000 ó255
0~100%

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
11
ARC + D
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó255
0~100%
2
Red
000 ó255
0~100%
3
Green
000 ó255
0~100%
4
Blue
000 ó255
0~100%
SOLID
Channel
Function
Value
Percent/Setting
1
Dimmer
000 ó255
0~100%
SPECIAL 1
Channel Function Value Percent/Setting
1
Red Module 1
000 ó255
0~100%
2
Green Module 1
000 ó255
0~100%
3
Blue Module 1
000 ó255
0~100%
4
Red Module 2
000 ó255
0~100%
5
Green Module 2
000 ó255
0~100%
6
Blue Module 2
000 ó255
0~100%

Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
12
Contact
Us
USA WORLD HEADQUARTERS
General Information - ILUMINARC
Address:5200 NW 108th Avenue
Sunrise, FL 33351
Voice: [phone]
Fax: [phone]
Technical Support
Voice: [phone]
Email: [e-mail]
World Wide Web
www.iluminarc.com
EUROPE
General Information - Chauvet Europe BVBA
Address:Stokstraat 18
9770 Kruishoutem
Belgium
Voice: [phone]
General Information - Chauvet Europe Ltd.
Address:Unit 1C
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK
NG16 6NT
Voice: [phone]
Fax: [phone]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.eu
Technical Support
Email: [e-mail]
World Wide Web
www.chauvetlighting.co.uk
MEXICO
General Information - Chauvet Mexico
Address:Av. Santa Ana 30
Parque Industrial Lerma
Lerma, Mexico C.P. 52000
Voice: [phone]
Technical Support
Email: [e-mail]
World Wide Web
www.chauvet.com.mx
Outside the U.S., United Kingdom, Ireland, Mexico, or Benelux contact the dealer of
record. Follow their instructions to request support or to return a product. Visit our website
for contact details.
Ilumiline Inground Tri-12 IP Optic 25 RGB QRG
Rev. 07
© Copyright 2015 ILUMINARC®
All rights reserved.
Printed in the P. R. C.