Impex MARCY ME-1016U User manual

NOTE:
Please read all
instructions carefully
before using this product
Table of Contents
Safety Notice
Important Assembly
Information
Care and Maintenance
Parts List
Warranty
Ordering Parts
Model
ME-1016U
Retain This
Manual for
Reference
180501
OWNER'S
MANUAL
MAGNETIC UPRIGHT BIKE
ME-1016U
IMPORTANT: Please read this manual before commencing
assembly of this product.
IMPEX®INC.
2801 S. Towne Ave, Pomona, CA 91766
Tel: [phone]
www.marcypro.com
[email protected]

1
© Impex Inc. www.marcypro.com
TABLE OF CONTENTS
BEFORE YOU BEGIN
Thank you for selecting MARCY MAGNETIC UPRIGHT BIKE ME-
1016U by IMPEX®INC. For your safety and benefit, read this manual
carefully before using the equipment. As a manufacturer, we are
committed to providing you with complete customer satisfaction. If you
have any questions, or find there are missing or damaged parts, we
guarantee you complete satisfaction through direct assistance from our
factory. To avoid unnecessary delays, please call our TOLL-FREE
customer service number. Our Customer Service Agents will provide
immediate assistance.
Toll-Free Customer Service Number
1-800-999-8899
Mon. –Fri. 9 a.m. –5 p.m. PST
www.marcypro.com
[email protected]
BEFORE YOU BEGIN
1
IMPORTANT SAFETY NOTICES
2
CARE AND MAINTENANCE
2
WARNING LABEL PLACEMENT
3
HARDWARE PACK
4
COMPONENTS
5
ASSEMBLY INSTRUCTIONS
6
EXPLODED DIAGRAM
12
PARTS LIST
14
COMPUTER INSTRUCTIONS
15
EXERCISE GUIDELINES
16
WARRANTY
18
ORDERING PARTS
18

2
© Impex Inc. www.marcypro.com
IMPORTANT SAFETY NOTICE
This exercise equipment is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual before
you assemble or operate your equipment. In particular, note the following safety precautions:
1. Read the warning notice and instruction prior to assembling and using the equipment.
2. This equipment is not intended for children under 12 years of age.
3. This equipment can be only used by hands or feet. Do not stand with full weight on the
pedals.
4. Do not leave children unattended with the equipment.
5. This equipment is intended for indoor use and for consumer use only.
6. Position the equipment on a clear, leveled surface. Make sure the surface is free of objects that
may cause tipping. Keep objects which could interfere with the user away.
7. Inspect before use. Keep frame padding in place. Never use the equipment if it is not
functioning properly.
8. Always wear appropriate workout clothing when exercising.
9. Do not use the equipment when it is wet.
10.Use the equipment only with mature, knowledgeable supervision.
11.Do not use the equipment while under influence of alcohol or drugs.
12.While keeping the head erect, focus eyes on the equipment toward the perimeter.
13.Before exercising, always do stretching exercises to properly warm up.
14.If the user experience dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
Care and Maintenance
1. For equipment information, contact the manufacturer.
2. Periodically inspect all parts to ensure all parts are functioning properly.
3. Replace any worn and/or damaged parts immediately.
4. Always keep the top surface of the pedals clean and dry.
5. Use mild household spray cleaners and/or a damp rag to wipe clean. Do not use harsh
cleaning chemicals.
6. Sand rusted areas on tubular members and repaint using a non-lead-based paint meeting
the requirements of Title 16 CFR Part 1303.
7. Disposal Instructions –The equipment can be safely disassembled and disposed.. Call
your local recycle agency regarding details of recycling.
8. Assembled dimensions: 33”x19.5”x52”
9. Maximum User Weight Capacity: 250 lbs.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS
ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH PRE-
EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY FITNESS
EQUIPMENT. IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY
DAMAGE SUSTAINED THROUGH THE USE OF THIS PRODUCT.
SAVE THESE INSTRUCTIONS.

3
© Impex Inc. www.marcypro.com
WARNING LABEL PLACEMENT
The warning labels shown here have been placed on the Base Frame. If the labels are missing or illegible,
please call customer service at 1-800-999-8899 for replacements. Apply the labels in the location shown.

4
© Impex Inc. www.marcypro.com
HARDWARE PACK
NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.
No.
Description
DRAWING
Q’ty
6
Carriage Bolt M10x3”
4
7
Curved Washer Φ⅜”
4
8
Domed Nut
4
11
Quick Release Knob
1
17
Allen Bolt M8x⅝”
4
27
Decorative Cover
1
28
T-type Knob
1
42
Curved Washer Φ⅓”
4
Box Wrench
1
Allen key L6
1

5
© Impex Inc. www.marcypro.com
COMPONENTS FOR ASSEMBLY
NO.1
1
NO.22
NO.18 NO.19
NO.15
NO.9
32
NO.10
NO.41 NO.16NO.3 NO.2
PART NO.
DESCRIPTION
Q’TY
1
Main frame
1
22
Front support
1
15
Seat support
1
18
Meter
1
9/10
Pedal ( L/R )
1/1
16
Seat
1
19
Handlebar
1
3
Front stabilizer
1
2
Rear stabilizer
1
41
Bottle holder
1

6
© Impex Inc. www.marcypro.com
ASSEMBLY INSTRUCTION
STEP 1
1. Attach the front stabilizer (#3) to the main frame (#1), Secure using two carriage bolts (#6),
two curved washers (#7), two domed nuts (#8).
2. Attach the rear stabilizer (#2) to the main frame (#1), Secure using two carriage bolts (#6),
two curved washers (#7), two domed nuts (#8)
1
2
3
6
6
6
7
87
87
8
7
8
21
23
21
42
42
17
17
23
22
20
24
20 24
23
21
42
25 26
27 28
18
24
43
19
11
15
31
33
34
32
16
9
10
70
41
75

7
© Impex Inc. www.marcypro.com
STEP 2
1. Take front post (#22) and connect the middle sensor wire (#24) to the lower sensor wire
(#23). Adjust the tension control knob (#20) to level 8, then connect it to the lower tension
cable (21).
2. Insert front post (#22) into main frame (#1) and tighten with 4 sets of Allen bolts (#17) and
curved washers (#42).
1
2
3
6
6
6
7
87
87
8
7
8
21
23
21
42
42
17
17
23
22
20
24
20 24
23
21
42
25 26
27 28
18
24
43
19
11
15
31
33
34
32
16
9
10
70
41
75

8
© Impex Inc. www.marcypro.com
HOW TO CONNECT TENSION CONNECTOR
Slide the Cable wire from the
extension sensor wire Connector
in between the opening on the wire
holder on sensor wire Connector.
Pull the extension sensor wire
Connector backward and slide the
wire through the slot on the bracket.
Drop down the Connector
so the fitting sits firmly on
top of the bracket.
NOTE: In able to hold the Front Post while connecting the cables and wires, extra help may
be needed

9
© Impex Inc. www.marcypro.com
STEP 3
1. Attach the handlebar (#19) to the front post (#22), tighten with a C-Clip (#25), Allen bolt
(#25), decorative cover (#27) and T-type knob (#28).
2. Connect the upper sensor wire from the back of the computer (#18) to the middle sensor
wire (#24).
3. Insert the lower pulse wire (#43) through the grommet (#75) on the front post (#22) and pull
the middle sensor wire (#43) out of front post (#22)
4. Connect lower pulse wire (#43) with the upper pulse wire from the back of the computer
(#18).
5. Attach computer (#18) to bracket on the front post (#22), tighten with four screws (#29).
1
2
3
6
6
6
7
87
87
8
7
8
21
23
21
42
42
17
17
23
22
20
24
20 24
23
21
42
25 26
27 28
18
24
43
19
11
15
31
33
34
32
16
70
41
75

10
© Impex Inc. www.marcypro.com
STEP 4
1. Attach the seat pad (#16) to the seat post (#15), tighten with knob (#34), sleeve
(#33), washer (#32) and bowl shaped nut (#31)).
2. Insert the seat post (#15) into the main frame (1) and tighten with quick release knob (#11).
11
15
31
33
34
32
16
1

11
© Impex Inc. www.marcypro.com
STEP 5
1. Attach the bottle holder (#41) to the front post (#22) with two self-tapping screws (#70).
2. Attach the left and right pedal straps to the left and right pedals (#9/#10).
3. Attach the left and right pedals (#9/#10) to the left and right crank arms.
Note: The pedals and crank arms are marked with "R" and "L" stickers. The left pedal (L)
should be threaded on clockwise and the right pedal (R) should be threaded on counter-
clockwise.
9
10
70
41
22

12
© Impex Inc. www.marcypro.com
EXPLODED DIAGRAM
15
1
2
3
6
6
5
5
21
23
25 26
27 28
20
22
18
6
4
4
42
7
17
17
87
87
8
7
8
9
10
11
24
19
35
36
37
39
38
40
43
70
16
30 31
33
34
12
13 14
32
41
42
42
75

13
© Impex Inc. www.marcypro.com
15
1
2
3
6
6
5
5
21
23
25 26
27 28
20
22
18
6
4
4
42
7
17
17
87
87
8
7
8
9
10
11
24
19
35
36
37
39
38
40
43
70
16
30 31
33
34
12
13 14
32
NO.1
1
NO.22
NO.18 NO.19
NO.15
NO.9
32
NO.10
NO.41 NO.16NO.3 NO.2
69
50
50
51
44
45
45
46
47
45
48
49
56
53
54
54 55
52
57
59
60
64 26
6667
68
69
12
14
14
72
73
74L
70
70
70
70
74R
71
71
71
71
71
70
58
63
62
61
70
70
70
41
42
42
71
71 71 71
75

14
© Impex Inc. www.marcypro.com
ME-1016U PARTS LIST
PART
NO.
DESCRIPTION
Q’TY
PART
NO.
DESCRIPTION
Q’TY
1
Main Frame
1
39
Screw
2
2
Rear Stabilizer
1
40
Bushing
1
3
Front Stabilizer
1
41
Bottle holder
1
4
End Cap For Front
Stabilizer
2
42
Curved Washer Φ⅓"
4
5
End Cap For Rear Stabilizer
2
43
Lower Pulse Wire
2
6
Carriage Bolt M10x3"
4
44
Axle for Flywheel
1
7
Curved Washer Φ⅜"
4
45
Bearing
3
8
Domed Nut M10
4
46
Washer
1
9
Left Pedal
1
47
Spring Clutch
1
10
Right Pedal
1
48
Small pulley
1
11
Quick Release Knob
1
49
Bearing
1
12
Washer
4
50
Nut M10
2
13
Locking Washer
3
51
Bowl Shaped Spacer
1
14
Aircraft Nut M8
5
52
Allen Bolt M8x4"
1
15
Seat Post
1
53
Crank
1
16
Seat
1
54
Ball Bearing assembly
1
17
Allen Bolt M8x⅝"
4
55
Pulley
1
18
Computer
1
56
Flywheel
1
19
Handlebar
1
57
Idler Assembly
1
20
Tension control w/ upper
cable wire
1
58
Belt
1
21
Lower tension cable
1
59
Magnetic Assembly
1
22
Front Post
1
60
Spacer
2
23
Lower Sensor Wire
1
61
Hex Bolt M8x1¾"
1
24
Middle Sensor Wire
1
62
Nut M6
1
25
Clip
1
63
Spring
1
26
Allen Bolt M8x¾"
2
64
Spacer
1
27
Decorative Cover for Clip
1
65
Spring
1
28
T-Type Knob
1
66
Hex Head Bolt M6x1"
1
29
Screw M5x½"
4
67
Nut M6
2
30
Sliding Tube
1
68
Sensor Bracket
1
31
Bowl Shaped Nut
1
69
French nut
2
32
Washer
1
70
Self-Tapping Screw
13
33
Sleeve
1
71
Self-Tapping Screw ST5x⅔"
9
34
Knob
1
72
Chain Cover L
1
35
End Cap
2
73
Chain Cover R
1
36
Foam Grip for Handlebar
2
74
Decorative Cover
1/1
37
Hand Pulse Sensor
2
75
Grommet
1
38
Washer
2

15
© Impex Inc. www.marcypro.com
COMPUTER
FUNCTIONAL BUTTONS:
MODE - Push down for selecting functions.
SET - To set the time, distance, calories and hand pulse.
RESET - For resetting time, distance, calories and hand pulse.
FUNCTION AND OPERATIONS:
1. SCAN: Press “MODE” button until “SCAN” appears, monitor will cycle through all the 6
functions: Time, speed, distance, calorie ODO and pulse. Each function will display for 6
seconds.
2.TIME: (1) Count the total time of exercise from start to end.
(2) Press “MODE” button until “TIME” appears, press “SET” button to set exercise time.
When the “set” is zero, the computer will sound an alarm for 15 seconds.
3.SPEED: Display current speed.
4. DIST: (1) Count the distance of exercise from start to end.
(2) Press “MODE” button until “DIST” appears. Press “SET” button to set exercise
distance. When the “set” is zero, the computer will sound an alarm for 15 seconds.
5.CALORIES: (1) Count the total calories of exercise from start to end.
(2) Press “MODE” button unit “CAL” appears. Press “SET” button to set
exercise calories. When the “set” is zero, the computer will sound an alarm for
15 seconds.
6. ODO：Monitor will display the total accumulated distance.
7. PULSE: Press MODE button until “PULSE” appears. Before measuring your pulse rate, please
place the palms of your hands on both contact pads and the monitor will show your
current heart beat rate in beats per minute(BPM) on the LCD after 6~7 seconds.
Note: During the pulse measurement, the measured value may be higher than the
actual pulse rate during the first 2~3 seconds, then will return to normal level. The
PULSE Function value cannot be regarded as the basis of medical treatment.
Press “MODE” button until “PULSE” appears. Press “SET” button to set exercise pulse.
The setting values of 40-240 RPM , the computer will sound alarm when heart rate is
below the SET value.
NOTE：
1. If the display is faint or does not show any digits, please replace the batteries.
2. The monitor will automatically shut off after 4 minutes of inactivity.

16
© Impex Inc. www.marcypro.com
SPECIFICATIONS:
FUNCTION
AUTO SCAN
Every 6 seconds
TIME
00:00’~99:59’
CURRENT SPEED
The maximum signal can be pickup is 99.9M/H
TRIP DISTANCE
0.00~99.99M or 0.00~9999M
CALORIES
0.1~999.9kCAL
ODO
0.1~999.9M or 1 ~ 9999M
PULSE RATE
40~240BPM
BATTERY TYPE
2pcs of SIZE –AA or UM –3
OPERATING TEMPERATURE
0°C ~ +40°C
STORAGE TEMPERATURE
-10°C ~ +60°C
EXERCISE GUIDELINES
Using your Magnetic Upright Bike will provide you with several benefits, it will improve your
physical fitness, tone muscle and in conjunction with calorie controlled diet help you lose weight.
1. The Warm Up Phase
This stage helps get the blood flowing around the body and the muscles working properly. It will
also reduce the risk of cramp and muscle injury. It is advisable to do a few stretching exercises as
shown below. Each stretch should be held for approximately 30 seconds, do not force or jerk your
muscles into a stretch - if it hurts, STOP.
2. The Exercise Phase
This is the stage where you put the effort in. After regular use, the muscles in your legs will become
more flexible. Work to your targeted heart rate but it is very important to maintain a steady tempo
throughout. The rate of work should be sufficient to raise your heartbeat into the target zone shown
on the graph below.
SIDE BENDS OUTER THIGH
INNER THIGH
FORWARD
BENDS
CALF / ACHILLES

17
© Impex Inc. www.marcypro.com
This stage should last for a minimum of 12 minutes though most people start at about 15-20
minutes
3. The Cool Down Phase
This stage is to let your Cardio-vascular System and muscles wind down. This is a repeat of the
warm up exercise e.g. reduce your tempo, continue for approximately 5 minutes. The stretching
exercises should now be repeated, again remembering not to force or jerk your muscles into the
stretch.
As you get fitter you may need to train longer and harder. It is advisable to train at least three times
a week, and if possible space your workouts evenly throughout the week.
MUSCLE TONING
To tone muscle while on your Magnetic Upright Bike you will need to have the resistance set
quite high. This will put more strain on our leg muscles and may mean you cannot train for as long
as you would like. If you are also trying to improve your fitness you need to alter your training
program. You should train as normal during the warm up and cool down phases, but towards the
end of the exercise phase you should increase resistance making your legs work harder. You will
have to reduce your speed to keep your heart rate in the target zone.
WEIGHT LOSS
The important factor here is the amount of effort you put in. The harder and longer you work
the more calories you will burn. Effectively this is the same as if you were training to
improve your fitness, the difference is the goal.

18
© Impex Inc. www.marcypro.com
IMPEX®INC.
LIMITED WARRANTY
IMPEX Inc. ("IMPEX®") warrants this product to be free from defects in workmanship and material, under normal use
and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to
the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option.
All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service
Department at 1-800-999-8899. All freights for products return to IMPEX must be prepaid by the customer. This
warranty does not extend to any product or damage to a product caused by or attributable to freight damage, abuse,
misuse, improper or abnormal usage or repairs not provided by an IMPEX authorized service center or for products used
for commercial or rental purposes. No other warranty beyond that specifically set forth above is authorized by IMPEX.
IMPEX is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the
use or performance of the product or other damages with respect to any economic loss, loss of property, loss of
revenues or profits, loss of enjoyments or use, costs of removal, installation or other consequential damages or
whatsoever natures. Some states do not allow the exclusion or limitation of incidental or consequential damages.
Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of merchantability
or fitness for a particular purpose is limited in its scope and duration to the terms set forth herein. Some states do not
allow limitations on how long an implied warranty lasts. Accordingly, the above limitation may not apply to you.
This warranty gives you specific legal right. You may also have other rights which vary from state to state. Register
on-line www.marcypro.com
IMPEX®INC.
2801 S. Towne Ave.
Pomona, CA 91766
ORDERING REPLACEMENT PARTS
Replacement parts can be ordered by calling our Customer Service Department toll-free at 1-800-999-8899 during our
regular business hours: Monday through Friday, 9 am until 5 pm Pacific standard time.
[email protected]
When ordering replacement part, always give the following information.
1. Model
2. Description of Parts
3. Part Number
4. Date of Purchase