InCarTec 29-UC050-REN1 User manual

Steering
control
Ignition
output
Illumination
Speed Pulse
Reverse
Handbrake
29-UC050-REN1
RENAULT ISO Canbus
STEERING CONTROL INTERFACE
Use this interface along with a head unit specific patch lead, pins 4, 8 and 12 terminate at
a 4 Pin connector, this is where you will need to connect the head unit patch lead.
When connected the CANbus interface will automatically recognise the vehicle. The
green LED on the interface will repeatedly flash once followed by a pause.
You will need to set the interface to the make of head unit you are fitting.
The amount of flashes between pauses corresponds to the make of head unit, see the
table overleaf for the number of flashes and which make it corresponds to.
While the LED is flashing green, press the Vol +/- buttons on the cars steering wheel to
change the amount of flashes between pauses, Vol + will increase the amount of flashes,
Vol–will decrease the amount of flashes.
When you have the correct amount of flashes, press seek+ to confirm and the LED will go
to a solid green light.
1 Yellow/Whtie = Handbrake output
2 Green = Can High
3 Orange = Illumination output
4 Brown = Steering control output
5 Pink = Ignition output
7 Red = 12V+ input
8 Black = Steering control output
9 White = Can Low
10 Blue = Reverse output
11 Grey = Speed pulse output
12 Purple = Steering control output
14 Black = Ground input
14 Pin connector on interface box as
seen from wire entry side.
1 2 3 4 5 6 7
8 9 10 11 12 13 14
Clio 2006-2008 √X X X X X
Clio 2009-> √√√√√√
Koleos 2008-2010 √√√√√√
Laguna 2006-2007 √X X X X X
Laguna III 2008-> √√√√√√
Megane 2006-2007 √X X X X X
Megane III 2008-> √√√√√√
Modus 2006-> √X X X X X
Traffic* 2008-> √X X X X X
Twingo 2009-> √√√√√√
* Includes Nissan Primastar
and Vauxhall Vivaro

Number of
flashes
Make of head unit
1 Clarion (Default)
2 Kenwood
3 JVC
4 Alpine
6 Pioneer (Set jumper)
7 Sony
To reprogram the interface for another head unit make
1. Disconnect the interface from the 14 Pin connector.
2. Push the reset button in and keep it pushed in.
3. Reconnect the interface to the 14 Pin connector
4. The LED will flash green then go off.
5. Release the reset button.
6. The LED will flash red then green.
7. Use Vol+/- to set the amount of flashes
8. Confirm selection with Seek +
To reset the interface (if installing into another vehicle)
With the interface powered, press and hold the rest button. When the LED goes off,
release the reset button. The LED will go to green and the reset is complete.
[email protected]o.uk 01392 829435 In Car Tec, 2 Leigham Units, Marsh Barton, Exeter, EX2 8HY
Setting the jumpers
There are a series of jumper pins on the interface board. These may need to be changed
depending on the head unit you are fitting or the type of outputs you require.
1 2 3
J1
J2
J3
J4
J5
JUMPERS 1 - 2 2 - 3
J1 ALPINE - SONY OUTPUT PIONEER OUTPUT
J2 GND BRAKE OUTPUT POSITIVE BRAKE OUTPUT
J3 GND REVERSE OUTPUT POSITIVE REVERSE OUTPUT
J4 BLAUPUNKT DO NOT USE
J5 K-BUS HANDLING CAN-BUS HANDLING