Infineon TRAVEO T2G Cluster 4M Lite Kit User manual

-
QUICK START GUIDE
Kit contents
TRAVEO™ T2G Cluster 4M Lite Kit
KIT_T2G_C-2D-4M_LITE
1. KIT_T2G_C-2D-4M_LITE REV-01 kit 2. USB Type-C to Type-C cable
www.infineon.com/traveoc2d4mlitekit

Powering up the kit
1. Ensure that you have the following:
–X103 (shorted between 2-3)
–X104 (shorted)
– X402 (shorted)
2. Connect the Type-C cable between X500 and Type-C port
of the PC.
3. Observe that the following power LEDs glow:
–3.3 V LED (D104)
–1.1 V LED (D102)
– 1.2 V LED (D103)
Pre-programmed code example
1. Connect the USB Micro-B cable (not part of the kit)
between X400 and the USB port of the PC.
2. Observe that the VBUS LED starts to glow with the other
power LEDs.
3. Open a UART terminal soware and connect with the
USB-UART COM port.
4. Select the baud rate to 115200 and then press the MCU
reset button S200.
5. Observe that the test results are printed on the serial
terminal window.*
6. Observe that the user LEDs blink continuously.
Program and debug
1. Use the onboard debugger (KitProg3) for programming
and debugging the board by connecting the USB Micro-B
cable between X400 and the USB port of the PC.
2. Additionally, use Cortex® Debug + ETM header (X302)
which is also available on the board.
3. Connect the suitable programming tool (IAR/GHS/
iSystem/Lauterbach) to one of the debugging interfaces.
4. Use a suitable IDE to program and debug the device.
Quick Start Guide Page 2 of 4
Power up the kit
1
Use the programming interface
3
Run the preloaded firmware
2
* Results in the serial terminal may varies as per the firmware changes.

KIT_T2G_C-2D-4M_LITE REV-01 board details
1 12V input power jack (X100)
2 Power LEDs (D104, D102, and D103)
3 USB Type-C connector (X500)
4 EZ-USBTM FX3 (CYUSB3014-BZXC – U500)
5 64 Mb HYPERRAMTM (S27KL0642DPBHA020 -U601)
6 512 Mb SEMPERTM flash (S26HL512TFPBHM010 - U600)
7 TRAVEOTM T2G CYT3DL device (MCU – U200)
8 FPD-Link connector (X700)
9 MIPI CSI-2 connector compatible
with e-CON module (X701)
10 External Crystal Oscillator (Y301) and
Watch Crystal Oscillator (Y300)
11 Pmod connector for Ethernet (X801)
12 20-pin IDC Arm® standard JTAG connector (X302)
13 Shield connector compatible with Arduino
(X802, X803, X805 and X806)
14 Connector compatible with
Shield2Go (Shield2Go_1-S800)*
15 Connector compatible with
Shield2Go (Shield2Go_2-S801)*
16 USB micro-B connector (X400)
17 PSoCTM 5LP (KitProg3) for programming
(CY8C5868LTI-LP039 - U400)
18 I/O connector compatible
with Raspberry Pi* (X800)
19 mikroBUS header (X812, X813)
20 TRAVEOTM T2G MCU reset button (S200)
21 KitProg3 reset jumper (X403)
22 Potentiometer (R904)
23 User LEDs (D900, D901) and
push button (S900)
24 EZ-USBTM FX3 reset button (S500)
25 EZ-USBTM FX3 bootloader jumper (X502)
* Footprint only, not populated on the board
Quick Start Guide Page 3 of 4
1 2 3 4 5 6 7 8
9
10
11
12
13
1413 15161718
19
19
20
21
22
23
24
25

Date: 11 / 2023
All rights reserved. © 2023
Infineon Technologies AG
Document number: 002-39115 Rev. **
Contact Technical Support to obtain kit documents and soware examples.
Published by Infineon Technologies AG
81726 Munich, Germany