Ingersoll-Rand ARO SP0665S2 Series User manual

OPERATOR’S MANUAL SP0665S2XXXXXXXX
INCLUDING: OPERATION, INSTALLATION AND MAINTENANCE.
INCLUDE MANUALS: SP0665S2XXXXXXXX Extrusion Pump (97999-1555), 66731-X Follower Plate
(pn 97999-213), 67342-X Follower Assembly (pn 97999-1099), 67347-X Follower Assembly (pn 97999-1102),
RM051S-XXX-XX-B Single Post Lift / Ram (pn 97999-1790) and S-636 General Information (pn 97999-636).
RELEASED: 3-24-10
REVISED: 4-14-17
(REV: E)
SINGLE POST RAM PACKAGE
5 Gallon
6” AIR MOTOR
65:1 RATIO
6” STROKE
READ THIS MANUAL CAREFULLY BEFORE INSTALLING,
OPERATING OR SERVICING THIS EQUIPMENT.
It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.
INGERSOLL RAND COMPANY LTD
209 NORTH MAIN STREET -BRYAN, OHIO 43506
[phone] FAX [phone] © 2017 CCN 15338031
arozone.com
SERVICE KITS
yUse only genuine ARO® replacement parts to assure com-
patible pressure rating and longest service life.
y637489 for repair of AF04XX-XX air motor.
y104302 for repair of R37121-100 regulator.
y104453 for repair of P39344-110 lter / regulator.
y637464-X4X for repair of 67348-X4X lower pump end.
y637465 for repair of lift / ram seals.
MODEL DESCRIPTION CHART
X
Refer to pump model operator’s manual
SP - Single Post
XXXXXXX
2
S
65
06
SP
06 - 6”
S - Chop-Check / Carbon Steel
2 - 5 gallon
E3 – 67342-1
E1 – 67342-2
E5 – 67342-3
EC – 66732
EA – 66732-1
65 - 65:1
Lower Pump End Options
Package
Package Option
Air Motor Size
Check Type / Wetted Materials
Mount Style
Follower Assembly
Pump Ratio
EB – 66732-2
A8 – 67347-1
A7 – 67347-2
T8 – 67347-11
T7 – 67347-12
0 - None - Basic Control for Ram only
2 - Advanced Ram and Pump Controls
SP0665S2XXXXXXXX
Figure 1
GENERAL DESCRIPTION
By delivering a smooth, continuous bead of the proper size,
an ARO system helps the operator maintain both production
rate and produce high quality standards. Maintained quality
standards assures that the material benefits are realized. To
further maximize operator production time, the ARO sys-
tem has a built-in lift / ram feature for quick and easy drum
changeover and easy lifting of the pump assembly from the
container.
ARO systems are totally enclosed, sealing the material in the
system from air and moisture, preventing premature cure-out
of the material. This allows for either continuous or intermit-
tent use of the system and allows the need for daily system
clean-up.
RAM PACKAGE

Page 2 of 4 SP0665S2XXXXXXXX (en)
INSTALLATION
The SP065S2XXXXXXXX Ram System comes completely as-
sembled. Remove the unit from the crate and place on a level
surface. Install the material hose and dispensing device as
required.
When the following instructions are observed, heavy paste
materials can be pumped directly from their original drum
without air inclusion or excessive waste. The follower plate
creates an air tight seal as well as clean-wiping action in its
progressive downward movement into the drum.
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS / INITIAL SET-UP PROCEDURE
WARNING
Stand clear when raising or lowering the lift.
Read the warnings on page 3 of RM051S-XXX-XX-B Single
Post Lift / Ram Operator’s Manual.
AIR CONTROLS
A - Air inlet
B - Ram pressure gauge
C - Ram air lter / regulator
D - Follower plate air supply valve
E - Ram control lever
F - Pump air lter / regulator
G - Pump air supply valve
H - Pump pressure gauge
DOFF ON
C
B
E
H
G
F
A
Figure 2
TO RAISE THE LIFT, (THE FIRST TIME):
1. Take note of the pump / drum clearance above. Be cer-
tain the lift / ram is clear of any objects above. Also, refer
to “Operating and Safety Precautions” found on page 3
of RM051S-XXX-XX-B Single Post Lift / Ram Operator’s
Manual.
2. Connect the air supply (115 psig / 7.9 bar max.) to the
air inlet. Adjust the air pressure on the lift / ram pressure
regulator (turn the knob clockwise) to 20 psig (1.4 bar).
3. Shift the control valve lever to the “up” position.
4. Raise the lift / ram high enough to clear the height of the
drum. Stop the lift upward travel by moving the control
valve lever to the “neutral”(center) position.
5. Once the lift / ram assembly and pump are in the “up” po-
sition, place and center an opened drum of material on
the lift / ram base.
6. Lubricate the lower follower wiper plate seal with grease.
NOTE: Make certain the grease is compatible with the
material being dispensed. This ensures a smooth t into
the drum, as well as prevents curing type compounds
from bonding to the seal.
7. Check the vent plug on the follower plate to be sure it
easily threads in and out. It is recommended to lubricate
the threads of the plug to help prevent possible set-up
of the compound at this point (see RM051S-XXX-XX-B
Operator’s Manual)
TO LOWER LIFT:
WARNING
PINCH HAZARD. Follower can descend
quickly, causing injury. Keep hands clear when align-
ing with container. Read the warnings on
page 3 of RM051S-XXX-XX-B Single Post Lift / Ram
Operator’s Manual.
NOTE: Be certain the follower plate vent plug has been re-
moved so that the air trapped between the follower and the
material is allowed to escape from this vent.
NOTE: The lift / ram may hesitate momentarily before start-
ing downward. The air pressure inside the post air chamber
must decrease before it will begin to descend.
1. Shift the control valve lever to the “down” position and
proceed to lower the pump.
2. Replace the vent plug once the material begins to ooze
from the vent opening.
3. The unit is now ready for operation. Open the pump air
supply valve. Adjust the air pressure on the pump lter /
regulator (turn the pump regulator knob clockwise) until
the pump begins to cycle.
4. Trigger the gun to prime the pump with material.

SP0665S2XXXXXXXX (en) Page 3 of 4
TO RAISE LIFT, (NORMAL OPERATION):
1. Close the pump air supply valve.
2. Adjust the follower plate air valve pressure up to approx-
imately 8 psig (0.55 bar). DO NOT OVER PRESSURIZE THE
DRUM to avoid damage. NOTE: Air from this valve will
only pass when the control lever is in the “up” position.
3. Shift the control valve lever to the “up” position.
4. Raise the lift / ram high enough to clear the height of the
drum. Stop the lift upward travel by moving the control
valve lever to the “neutral”(center) position.
TO CHANGE THE DRUM:
NOTE: The control valve lever must be in the “neutral” posi-
tion and the pump air supply valve should be closed.
1. To avoid damage, DO NOT OVER PRESSURIZE THE DRUM.
2. Open the follower plate air supply valve to allow air un-
der the follower plate.
3. Shift the control valve lever to the “up” position.
4. Unscrew the thumb screw and remove the old drum.
PARTS LIST / SP0665S2XXXXXXXX
Item Description (size) Qty Part No.
1 Pump Assembly (1) AF0665S1XXXXX
*2 Male Elbow
(1/2 - 14 NPT x 1/2” o.d. tube)
(included with item 3)
(1) 59756-362
*3 Single Post Lift / Ram (1) RM051S-XXX-XX-B
*4 Follower Assembly
(see "Model Description Chart", page 1)
(1)
5 Washer (3/8”) (4) Y13-6-C
6 Cap Screw (3/8" - 16 x 1-1/2”) (4) Y6-67-C
7Lock Washer (3/8”) (4) Y14-616-C
Item Description (size) Qty Part No.
8Nut (3/8” - 16) (4) Y12-6-C
9Wet-Sol “Plus” (1 quart) (not shown) (1) 66333-B
*10 Tubing (5/16” od x 38”) (1) 94980-()
*11 Tubing (1/2” od x 33”) (1) 94978-()
*12 Cap Screw (4) Y99-63-C
*13 Male Elbow (1) 59756-58
 Bulk Tubing (1/2” od x 100’) (1) 94978-100
 Bulk Tubing (5/16” od x 100’) (1) 94980-100
*Included with RM051S-XXX-XX-B.
1
2
3
4
6 
10
12 13
5
7
8
11
Figure 3DIMENSIONAL DATA
ASSEMBLY TORQUE REQUIREMENTS 
NOTE: DO NOT OVERTIGHTEN FASTENERS.
(6) cap screw, 25 - 30 ft lbs (33.9 - 40.7 Nm).
LUBRICATION / SEALANTS
Apply anaerobic pipe sealant to all male pipe threads.

Page 4 of 4 SP0665S2XXXXXXXX (en)
PN 97999-1555
12.000”
∅ (0.562”)
4 PLACES
15.000”
21.417”
55.605”
80.605”
25.000”
16.000”
19.000”
24.916”
Figure 4