INIM Electronics Air2 Series Assembly instructions

1
Installation and programming manual
Air2
Wireless devices
Installation and programming manual
EN 50131-1
EN 50131-5-3
EN 50130-4
EN 50130-5

2
Wireless devices
Table of
contents
Chapter 1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-1 About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-2 Manufacturer's details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-3 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-4 Notes from the Manufacturer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Chapter 2 Description of products . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2-1 Air2-BS200 Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2-2 Air2-IR100 and Air2-IR100/C PIR detectors. . . . . . . . . . . . . . . . . . . . . .6
2-3 Air2-MC100 magnetic contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2-4 Air2-MC200 magnetic contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2-5 Air2-KF100 remote-control keyfob . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2-6 Air2-FD100 smoke detector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Chapter 3 Operating principles. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
3-1 Air2-BS200 address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3-2 Wireless terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3-3 Aria Keypad and Hedera sounder . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Chapter 4 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4-1 Installing the Air2-BS200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4-2 Installing the IR100 and IR100/C. . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
• Installing the Air2-MC100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
4-3 Installing the Air2-MC200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-4 Installing the Air2-KF100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-5 Installing the Air2-FD100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
4-6 Addressing the Air2-BS200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4-7 Enrolling the devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Chapter 5 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5-1 Programming via keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
5-2 Programming via the Air2-BS200 module . . . . . . . . . . . . . . . . . . . . . . .18
5-3 Air2-BS200 module default settings . . . . . . . . . . . . . . . . . . . . . . . . . . .19
5-4 Options programmable at the control panel. . . . . . . . . . . . . . . . . . . . . .19
Appendix A Declaration of conformity of the Air2-BS200. . . . . . . . . . . . 21
Appendix B Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Copyright The information contained in this document is the sole property of INIM
Electronics s.r.l. No part may be copied without written authorization
from INIM Electronics s.r.l.
All rights reserved.

General information 3
Installation and programming manual
Chapter 1
GENERAL INFORMATION
1-1
About this manual
MANUAL CODE DCMIINE0A2BS200E
REVISION 1.00
1-2Manufacturer's details
Manufacturer: INIM Electronics s.r.l.
Production plant: Via Fosso Antico - Centobuchi
63076, Monteprandone (AP) - Italy
Tel.: [phone]
Fax: [phone]
e-mail: [email protected]
Web: www.inim.biz
The persons authorized by the manufacturer to repair or replace the parts of this
system, hold authorization to work on INIM Electronics brand devices only.
1-3System Description
The advanced Air2 two-way wireless intrusion protection system (868MHz
frequency) integrates directly with all models in INIM intrusion control panel
range.
Air2 system devices:
• Air2–BS200/50 transceiver module, 50 terminals
•
Air2–BS200/30 transceiver module, 30 terminals
•
Air2–BS200/10 transceiver module, 10 terminals
•
Air2–IR100 passive infrared detector, 12m
•
Air2–IR100/C passive infrared detector, 20m
•
Air2–MC100 magnetic contact with two I/O terminals, in white or brown
•
Air2–MC200 magnetic contact with shock and tilt sensor in white or brown
•
Air2–KF100 4 button remote-control key
•
Air2–FD100 smoke detector
•
Air2-Aria keypad with graphic display
•
Air2-Hedera outdoor sounder, in white or chrome effect
•
Air2-DT200T dual technology curtain detector, in white or brown
•
Air2-XIR200W PIR detector, 12m
•
Air2-XDT200W dual technology curtain detector
•
Air2-UT100 universal transceiver
•
Air2-ODI100W outdoor wireless dual-infrared detector
•
Air2-OTT100W outdoor wireless triple-technology detector
Table 1: Technical specifications of Air2 system
Operating frequency range
868.0 - 868.6MHz
selectable channels 868.1, 868.3, 868.5MHz
Communication type Two-way
Modulation GFSK
Device supervision From 12 to 250 minutes
Security grade 2
Environmental class II

4General information
Wireless accessories
Each SmartLiving control panel supports more than one Air2-BS100 module,
connected via I-BUS, in accordance with the contents of the table:
For optimal performance of the wireless system the Air2-BS100 transceiver
module must be located at the core of the wireless network devices and area of
use of remote-control keys, in a placement which allows easy connection of the I-
BUS cable to the control panel.
All wireless protection devices should be installed in elevated positions in order to
increase detection capabilities and prevent inadvertent blinding caused by large
objects or building occupants.
The signal strength (transmitted/received by the Air2-BS200 transceiver module)
of each wireless device can be viewed on the keypads and via SmartLeague
software, this information can be used to optimize the installation process.
Note A level 3 signal strenght it is recommended for a good installation.
As an integral part of the system, the Air2 provides 3 inter-module transmission
channels. This feature allows you to select the channel in such way as to avoid
over-the-air interference between two close-proximity wireless systems (for
example, in two adjoining apartments).
For secure deployment and operations of the Air2 wireless intrusion protection
system, it is necessary to refer to the Installation and programming guide of the
hardwired intrusion control panel in use.
1-4Notes from the
Manufacturer
Note The Air2-MC100 device is certified by IMQ-Sistemi di sicurezza (Italian
certification body).
The notified body N°0051, intervened in the R&TTE Directive conformity
assessment procedure for all the devices of the Air2 system, with the exception of
the Air2-FD100 and Air2-MC200.
The information relating to the power-supply batteries required by Air2 devices is
shown in the Technical Specification table that follows.
The manufacturer cannot guarantee the declared battery life.
ATTENTION! Do not use batteries other than those indicated by the manufacturer as they may
explode.
Used batteries must be disposed in accordance with local regulations.
For the technical description and installation instructions of any Air2 devices not
described in this manual, refer to the respective manuals included in the
packaging of the various devices.
Table 2: Number of Air2-BS100 managed by the control panel
Control
panel FW SmartLiving control panel Notes
505 515 1050 10100
6.00
10 20 30 Does not manage Air2-
Aria and Air2-Hedera
6.01 10 20 30 Manages all Air2 devices

Description of products 5
Installation and programming manual
Chapter 2
DESCRIPTION OF
PRODUCTS
2-1
Air2-BS200 Transceiver
The Air2-BS200 wireless module allows the integration and management of
wireless detectors, keypads, sounders in the hardwired environments of all
models of INIM intrusion control panels.
The module simulates:
• a reader, at a programmed address (ADD), which allows you to configure the
keyfobs
• up to 10 expansion boards, at addresses ADD, ADD+1, ... ADD+9, capable of
managing the terminals.
Additionally, each Air2-BS200 allows the SmartLiving control panel to manage up
to 4 Aria wireless keypads and 4 Hedera wireless sounders.
I
EN 50131-1
EN 50131-5-3
EN 50130-4
EN 50130-5
Table 3: Technical specifications of the Air2-BS200
Models BS200/50 BS200/30 BS200/10
Power Supply Voltage 10.5 - 16 V
Maximum current draw 30 - 50 mA
Bus type I-BUS / BUS RS485
Antenna connector SMA female
Antenna impedance 50 Ohm
Security grade 2
Environmental class II
Operating temperature and
humidity
-10°C +40°C, 93%
Dimensions (W x H x D) 80 x 170 x 25 mm
Weight 135 g
Terminals 50 30 10
Keyfobs 100 50 30
Aria keypad 4
Hedera Sounder 4
Table 4: Description of the Air2-BS200 parts
A
Bus connection terminals (I-BUS
and BUS RS485)
B
Connectors for the selection of
the BUS type
C
Connectors for the EOL position
(BUS RS485)
D Tamper microswitch: Open cover
E
Tamper microswitch:
Dislodgement
F Button P1
G Button P2
H LED DL1 - red
I LED DL2 - blue
J LED DL3 - green
K LED DL4 - yellow
L PRG LED - red
M Antenna connector
BC
E
H
A
F
Air2-BS200
PCB
D
G
IJK L
M

6Description of products
Wireless accessories
2-2Air2-IR100 and Air2-IR100/C
PIR detectors
Air2-IR100 is a two-way communication PIR detector with 12m coverage. The
device is protected against dislodgement and open-cover tamper. You can adjust
the device sensitivity (accepted value between 1 and 4) from the keypad or
through the SmartLeague software application.
The Air2-IR100/C PIR detector has the same features as the Air2-IR100 but
covers a greater distance (20m) with a minor angle.
N Mounting screw location
O Tamper screw hole
P Cable entry
Q Enclosure screw hole
Table 4: Description of the Air2-BS200 parts
Air2-BS200
Backbox
Q
P
N N
O
N N
Table 5: LED Signals
LED DL1
red LED DL2 blue LED DL3 green LED DL4 yellow PRG LED red Signal
Off Discontinuou
s flashing Off Off Off Wireless data reception
Off Off Discontinuou
s flashing Off Off Programming phase running (from 1 to 5)
Off Off Off solid/
blinking Off Parameter/Value undergoing programming
Off Off Continuous
flashing Off Off Enrollment of wireless device in progress (requested at the control panel)
Off Off Continuous
flashing Continuous flashing Off Erroneous programming (for example, two devices on the same terminal)
1 flash 1 flash 1 flash 1 flash Off Reset factory default settings
solid/off/blinking solid Address Programming (phase 6)
EN 50131-1
EN 50131-5-3
EN 50131-2-2
EN 50130-4
EN 50130-5
INCERT
CEB T014
Table 6: Technical specifications of the Air2-IR100
Models IR100 IR100/C
Battery Lithium CR123A 3V
Battery life 3 years
“Low battery” fault voltage Less than 2.4V
Stand-by current draw 51μA
Maximum current draw 30mA
PIR range 12 m 20 m
Lens angle 80° 80° to 6m
7° to 20m
Operating temperature and
humidity
-10°C +40°C, 93%
Dimensions (W x H x D) 58 x 100 x 44 mm
Weight 80g
Security grade 2
Environmental class II

Description of products 7
Installation and programming manual
I
VOLUMETRIC
COVERAGE
The following volumetric-coverage diagrams refer to detectors whose sensitivity is
set by the control panel at maximum sensitivity.
Table 7: Description of Air2-IR100 parts
A Battery
B Antenna
C Signalling LED - red
D PIR detector
E Open-tamper microswitch
F ENROLL microswitch
G Mounting screw hole
H Tamper screw hole
I Enclosure screw hole
Air2-IR100 -
PCB
A
B
C
DE
F
G
H
GG
I
Air2-IR100 -
Backbox
20.0°20.0°
80.0°80.0°
7.0°7.0°
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20m0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20m
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20m0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20m
2.2m2.2m
0 1 2 3 4 5 6 7 8 9 10 11 12m0 1 2 3 4 5 6 7 8 9 10 11 12m
94.75°94.75°
0 1 2 3 4 5 6 7 8 9 10 11 12m0 1 2 3 4 5 6 7 8 9 10 11 12m
2.2m2.2m
Air2-IR100/C
Top view
Air2-IR100/C
Side view
Air2-IR100
Top view
Air2-IR100
Side view

8Description of products
Wireless accessories
2-3Air2-MC100 magnetic contact
The Air2-MC100 magnetic contact has two screw-in positions for placement
optimization of the device magnet, 90° one from the other.
It also provides Alarms two terminals which can be configured as inputs or open-
collector outputs. Configuring the terminals as inputs provides standard zone
management (NO, NC, Single Balancing, Double Balancing) and allows direct
connection to rollerblind sensors.
Alarms deriving from magnetic contacts and distinctly from the two terminals are
signalled separately on the control panel.
The device is protected against dislodgement and open-cover tamper.
The following table indicates the distance in millimetres of the operating capacity
of the magnet depending on the side in use and the axes illustrated in the figure
(values starting from a nominal distance of 10mm, except for axis y-):
EN 50131-1
EN 50131-5-3
EN 50131-2-6
EN 50130-4
EN 50130-5
INCERT
CEB T014
Table 8: Technical specifications of the Air2-MC100
Battery Lithium CR123A 3V
Battery life 4 years
“Low battery” fault voltage Less than 2.4V
Stand-by current draw 21μA
Maximum current draw 30mA
Open-collector output Max 50 mA
Operating temperature and
humidity
-10°C +40°C, 93%
Dimensions (W x H x D) 36 x 95 x 26 mm
Weight 130 g
Magnet dimensions 13 x 40 x 14 mm
Colours White, Brown
Security grade 2
Environmental class II
Table 9: Description of Air2-MC100 parts
A Battery
B Antenna
C Signalling LED - red
D Open-tamper microswitch
E
Dislodgement-tamper
microswitch
F ENROLL microswitch
G GND terminal
H Terminal T1
I Terminal T2
J Map of terminals
K Reed contact: short side
L Reed contact: long side
M Mounting screw hole
N Tamper screw hole
O Magnet - short side
P Magnet - long side
Q Enclosure screw hole
CR123A 3V + -
CR123A
3V
+
+
+
+
-
-
-
-
E
J
G
H
I
K
A
B
C
D
F
M
N
O
O
P
P
L
Q
Air2-MC100
Backbox
Air2-MC100 - PCB
M
x
z
y
x
z
y
Table 10: Distance between magnet and contact (mm)
Axis Contact long side Contact short side
Withdrawn Near Withdrawn Near
x +/-
21 15 25 20
y - 21 15 19 15
z +/- 11 9 11 9

Description of products 9
Installation and programming manual
In order to comply with the EN 50131 series of standards, double balancing is
required when either terminal T1 or T2 is configured as an input.
ATTENTION! Ferromagnetic materials which are located in the vicinity of the mounting position
can influence the magnetic field and can result in the reduced operating capacity
of the device.
2-4Air2-MC200 magnetic contact
The Air2-MC200 is supplied with a magnet which is to be secured (by means of two
screws) to the side of the contact, in the position indicated by the two notches.
The Air2-MC200 integrates a shock and tilt sensor that allows its use without the
need of the magnet.
The Air2-MC200 is equipped with open and dislodgement tamper protection.
The device uses separate channels for the different types of signalling,, thus
allowing precise identification of the alarm source.
MAGNET
DETECTION RANGE
The following table indicates the distance in millimeters of the operating capacity
of the magnet depending on the side in use and the axes illustrated in the figure
(values starting from a nominal distance of 10mm, except for axis y-):
SHOCK DETECTION Signalling of shock waves is achieved through a tri-axial vibration sensor. The
vibration sensibility can be set either from a keypad or via the SmartLeague
software application.
EN 50131-1
EN 50131-5-3
EN 50131-2-6
EN 50130-4
EN 50130-5
Table 11: Air2-MC200 technical specifications
Battery Lithium CR2 3V
Battery life 4 years
“Low battery” fault voltage Less than 2.4V
Stand-by current draw 10μA
Maximum current draw 30mA
Operating temperature and
humidity
-10°C +40°C, 93%
Dimensions (W x H x D) 35 x 58 x 23 mm
Weight 30 g
Magnet dimensions 13 x 40 x 14 mm
Colours White, Brown
Security grade 2
Environmental class II
Table 12: Description of Air2-MC200 parts
A Battery
B
Signalling LED - red (on
rear)
C
Microswitch: open/
dislodgement/ENROLL
D Reed contact
E Mounting screw hole
F Tamper screw hole
G Securing screws
H Magnet position notches
CR2- 3V + -
CR2-
3V
+
+
+
+
-
-
-
-
E
G
H
A
B
C
DF
Air2-MC200 - box
Air2-MC200 - PCB
H
x
zy
Table 13: Distance between magnet and contact (mm)
Axis Contact long side
Withdrawn Near
x +/-
18 14
y - 18 14
z +/- 22 18

10 Description of products
Wireless accessories
TILT DETECTION Signalling of tilting (angle change) is achieved through tri-axial tilt sensing. The tilt-
variation value (angle) can be set in relation to the standby position, which is saved
to the memory during the reset-after -alarm phase.
If both shock and tilt sensing are activated, alarm signalling will occur as soon as
one of the two conditions exceeds it respective alarm threshold.
ATTENTION! Ferromagnetic materials which are located in the vicinity of the mounting position
can influence the magnetic field and can result in the reduced operating capacity
of the device.
2-5Air2-KF100 remote-control
keyfob
The Air2-KF100 keyfob has 4 button which can be programmed from the control
panel.
The graphic-choice feature allows you to identify the buttons by numbers or icons.
Thanks to the two-way supervision of the Air2-BS200, the Air2-KF100 keyfob
imparts audible and visual feedback signals (beep and LED signals) which notify
the user of the successful outcome of requested operations.
EN 50131-1
EN 50131-5-3
EN 50130-4
EN 50130-5
INCERT
CEB T014
Table 14: Technical specifications of the Air2-KF100
Battery Lithium CR2032 3V
“Low battery” fault voltage Less than 2.4V
Stand-by current draw 0A
Maximum current draw 30mA
Buzzer Multitone
Operating temperature and
humidity
-10°C +40°C, 93%
Dimensions (W x H x D) 61 x 41 x 12 mm
Weight 15 g
Rubber push-buttons
•withicons
• with numbers
Security grade 2
Environmental class II
Number of available PIN code
combinations
2
24
Table 15: Description of Air2-KF100 parts
A Key1/F1, LED1-red
B Key2/F2, LED2-red
C Key3/F3, LED3-red
D Key4/F4, LED4-red
E Confirmation LED - red/green
F Icon graphic keys
G Keys with numbers
AB
C
D
E
FC
G
A
EB
D
Table 16: Air2-KF100 Notifications
Push
button LED 1 LED 2 LED 3 LED 4 Buzzer signal Operation
F1
1 flash beep Activates shortcut 1
F2 1 flash beep Activates shortcut 2
F3 1 flash beep Activates shortcut 3
F4 1 flash beep Activates shortcut 4
F2 + F3 1 flash 1 flash beep Block/Unblock remote-
control device
F3 + F4 1 flash 1 flash beep Enrolling
Any 4 flashes 4 flashes Keyfob locked signal

Description of products 11
Installation and programming manual
Failure of the LED to light, after pressing the corresponding button and the
successful execution of the command, is an indication that the wireless battery is
running low.
ROLLING-CODE
AUTHENTICATION
A further guarantee of security for Air2-KF100 keyfob wireless transmissions are
the over-the-air random codes. These random codes allow the Air2-BS200 to
authenticate the validity of each wireless keyfob transmission.
In the event of irregular wireless activity, denial-of-request will be signalled by an
audible error signal ( “bop”).
To reset wireless transmissions and rolling code authentication, press and hold
keys “F3” and “F4” simultaneously.
This feature is active at default but can be disabled during the programming phase
of the Air2-BS200 module (details follow). If an Air2-KF100 wireless keyfob is used
on several systems, it is impractical to leave this feature enabled.
2-6Air2-FD100 smoke detector
The Air2-FD100 detector is capable of sensing the presence of smoke particles
and thus detecting a fire in its early stages.
Air2-FD100 optical smoke detector is equipped with a sampling chamber (based on
light scattering mass - Tyndall effect). In order to ensure the proper operating capacity
of the device, it must be installed away from drafts and large objects which may alter
the airflow to the sampling chamber.
ATTENTION! The sole task of the Air2-FD100 smoke detector is to sense for smoke in the
protected area. Therefore, in no way can the combination of a SmartLiving system
and an Air2-FD100 smoke detector be considered a fire control system.
The operating parameters can be changed and adapted to the environmental
conditions, either from the control panel or through the SmartLeague software
application. The detector signals alarm status when the level of smoke in the
protected environment reaches the following levels:
• 0.08 dB/m (pre-set mode)
•0.10dB/m
•0.12dB/m
•0.15dB/m
Table 17: Panel notifications
Panel response Confirmation LED Buzzer signal
green red
Command not received
1 flash
Operation not done 4 flashes bop
Operation done 3 flashes long beep
EN 50131-1
EN 50131-5-3
EN 50130-4
EN 50130-5
Table 18: Air2-FD100 technical specifications
Battery Lithium CR17450 3V
Battery life 3 years
“Low battery” fault voltage Less than 2.4V
Current draw during standby 70μA
Current draw during alarm Max 40mA
Operating temperature and
humidity
-5°C +40°C, 95%
Height (base included) 60mm
Diameter (base included) 114mm
Weight
(base and battery included)
182 gr

12 Description of products
Wireless accessories
The tricolour LED (360° visibility) indicates the detector status.
• Green - one flash every 15 seconds : detector not operating properly.
•
Green - one flash every 40 seconds : low battery.
•
Yellow - On solid : fault present.
•
Yellow - flashing : sampling chamber contaminated (with dust, etc.).
•
Red - On solid : detector in alarm status.
Table 19: Description of Air2-FD100 parts
A Detector
B LED red/yellow/green
C Optical chamber
D Battery
E Tamper microswitch
F ENROLL microswitch
G Base
H Mounting screw hole
F
E
D
H
H
G
A
B
C
A

Operating principles 13
Installation and programming manual
Chapter 3
OPERATING PRINCIPLES
3-1
Air2-BS200 address
In order to configure the Air2-BS200 in the control panel it is necessary to assign
an address between 1 and 30 (to set the address follow the instructions in
paragraph 4-6 Addressing the Air2-BS200).
The selected address will be assigned to the simulated reader (which processes
and manages wireless transmissions in the same way as keys) and to the first 10
expansion boards, also simulated, with successive addresses “ADD”, “ADD”+1, ...,
“ADD”+9.
Conditions for secure deployment and operations:
• there must be no other transceivers at the selected address
• the simulated reader must be enrolled on the control panel
• there must be no other readers (nBy/X, nBy/S, JOY/MAX or Alien) at the selected
address
• the simulated reader need not be associated with any partitions
• the simulated expansion boards must be enrolled on the control panel
• an expansion board will be considered part of the wireless network only when one
of its terminals is configured as “wireless”
• a simulated expansion board cannot share its assigned address with other
hardwired FLEX5 expansion boards.
3-2Wireless terminals
A terminal can be considered a “Wireless” terminal only under the following
conditions:
• it must not be configured as a “Double” zone (D)
• if configured as a “Zone”, it must not be configured as “Shock” in the detector type
field
• it must be assigned to an expansion board (and not to the control panel or
keypads)
3-3Aria Keypad and Hedera
sounder
The SmartLiving control panel can manage up to 4 Aria keypads and 4 Hedera
sounders for each Air2-BS200 installed. However, each control panel model
supports a maximum number of keypads and sounders which must be respected.
During the addressing phase it is necessary to use free addresses only and to
ensure that no other keypads (Joy, Concept, NCode or Alien) are present at the
address of the Aria keypads, or other sounderflashers (Ivy) at the address of the
Hedera sounderflashers to be included in the configuration.
For the addressing procedure and the programming of these devices, refer to the
respective manuals.

14 Installation
Wireless accessories
Chapter 4
INSTALLATION
4-1
Installing the Air2-BS200
1. Choose a suitable mounting placement.
2. Using a flat-bladed screwdriver in the enclosure screw location, push open the
enclosure and separate the two parts.
3. Hold the base to the chosen mounting placement and mark the screw holes
and tamper protection position.
4. Pull the wires through the cable entry and wire up the Air2-BS200.
5. Using the screws, secure the base and the tamper protection in position.
6. Set the selection jumpers for the Bus type (position Afor I-BUS or position
Bfor RS485).
If necessary, in the case of the RS485 BUS, set the jumper for the EOL posi-
tion (position Cfor EOL).
7. Enroll the device.
8. Re-attach the cover to the base and replace the enclosure screw.
4-2Installing the IR100 and
IR100/C
1. Choose a suitable mounting placement.
2. Using a flat-bladed screwdriver in the enclosure screw location, push open the
enclosure and separate the two parts.
3. Push the board grip to release and remove the PCB.
4. Open the anchor-screw holes.
5. Hold the base to the chosen mounting placement and mark the screw holes
and tamper protection position.
6. Using the screws, secure the base and the tamper protection in position.
7. Replace the PCB.
8. Insert the battery, ensure you respect the proper polarity.
9. Enroll the device.
10. Re-attach the cover to the base and replace the enclosure screw.
NOTES • The recommended installation height is 2.2m.
• Be careful not to drill in the vicinity of electrical wiring or plumbing/gas pipes, etc.
• Avoid installing the detector close to the following sources of interference:
reflective surfaces, direct air flow from vents, drafts, fans, windows, sources of
steam, sources of oil vapour, sources of infrared rays, and objects which can cause
temperature changes such as heaters, refrigerators and ovens.
• Do not place large objects (machinery or furniture) in front of the detector.
• The alarm LED must be above the lens.
Installing the Air2-MC100
1. Choose a suitable mounting placement.
2. Using a flat-bladed screwdriver in the enclosure screw location, push open the
enclosure and separate the two parts.
3. Push the board grip to release and remove the PCB.
4. If you use terminal T1 or T2, open the respective wire entry and pull the
wires through.
5. Hold the base to the chosen mounting placement and mark the screw holes
and tamper protection position.
ABC

Installation 15
Installation and programming manual
6. Using the screws, secure the base and the tamper protection in position.
7. Replace the PCB.
8. Insert the battery, ensure you respect the proper polarity.
9. Enroll the device.
10. If you wish to fit the magnet by means of the screws (included), remove the
magnet base by means of a flat-bladed screwdriver.
11. Locate the magnet (long or short side in the required position) on the con-
tact, at a distance of about 2 mm from the magnetic reed contact. If you
are using the long side, use the notches on the base in order to position it
correctly.
12. Using the screws or the adhesive tape, attach the magnet.
13. Re-attach the cover to the base of the contact and replace the enclosure
screw.
4-3Installing the Air2-MC200
1. Choose a suitable mounting placement.
2. Using a flat-bladed screwdriver in the enclosure screw location, push open the
enclosure and separate the two parts.
3. Hold the base to the chosen mounting placement and mark the screw holes
and tamper protection position.
4. Using the screws, secure the base and the tamper protection in position.
5. Insert the battery, ensure you respect the proper polarity.
6. Enroll the device.
7. If you wish to fit the magnet, work through the steps described in the pre-
vious paragraph.
8. Re-attach the cover to the base of the contact and replace the enclosure
screw.
4-4Installing the Air2-KF100
The Air2-KF100 requires enrolling only.
If it becomes necessary to replace the device cover or battery, work through the
following steps.
1. Remove the enclosure screw on the back of the keyfob and open the device.
2. Remove the cover.
3. Replace the cover/battery as required.
4. Close the device and replace the enclosure screw.
5. Enroll the key.
4-5Installing the Air2-FD100
1. Choose a suitable mounting placement.
2. Hold the base to the chosen mounting placement and mark the screw loca-
tions.
3. Insert the battery, ensure you respect the proper polarity.
4. Attach the battery cover.
5. Position the detector over the base and, with minimum force, turn it clockwise
until notch “A” aligns with notch “B” (in order to attach the detector to the
base); turn it still further until notch “A” aligns with notch “C” (in order to
allow the base to close the tamper microswitch).
6. Enroll the device.
A
B
C

16 Installation
Wireless accessories
4-6Addressing the Air2-BS200
The address (“ADD”) to be assigned to the Air2-BS200 transceiver must be the
same as the address of the simulated reader.
The address assignment phase takes place during programming phase 6 of the
module (refer to paragraph 5-2 Programming via the Air2-BS200 module). During
this phase the address is indicated by LEDs DL 1-4 in accordance with the
following sequence:
1. Place the SmartLiving control panel in maintenance mode.
2. Use the P1 button to access the address setting menu (phase 6 of the pro-
gramming session). During this phase the PRG LED will switch On and the
LEDs will show the current address.
3. Use the P2 to reach the address to be assigned.
4. Use the P1 button to assign the address and exit the menu (phase 0).
5. Include the wireless expansion boards in the control panel configuration,
starting from the “ADD” address (maximum “ADD” +9).
6. Enroll the wireless reader at the “ADD” address.
Pressing and holding the P2 button during normal operating status of the Air2-
BS200 will allow you to view (but not change) the transceiver address indicated on
its LEDs.
Table 20: Panel notifications
Reader
address LED DL1 - red LED DL2 - blue LED DL3 - green LED DL4 - yellow
100010
LED Off
200101 LED On
30011L Flashing LED
40100
50101
60110
70111
81000
91001
10 1010
11 1011
12 1100
13 1101
14 1110
15 1111
16 0 0 0 L
17 0 0 L 0
18 0 0 L L
19 0 L 0 0
20 0L0L
21 0 L L 0
22 0 L L L
23 L 0 0 0
24 L 0 0 L
25 L0L0
26 L 0 L L
27 L L 0 0
28 L L 0 L
29 L L L 0
30 LLLL

Installation 17
Installation and programming manual
4-7Enrolling the devices
1. Select the expansion board at the “ADD” address and then select the termi-
nal in question.
2. Configuring the terminal as “Wireless”:
Via keypad: press key ; the word “Wireless” will appear on the last
line on the display
Via SmartLeague: using the right button on the mouse, select “Wireless”.
ATTENTION! If any terminal on the expansion board is configured as “wireless”, all the
remaining terminals must be configured as “wireless” terminals.
3. Configuring the type of terminal:
INPUT - for Air2-IR100 and Air2-MC100 devices
DOUBLE ZONE - for Air2-MC200 devices
4. Enrolling the wireless terminals.
From keypad: access the zone programming section by pressing the
key.
Go to the “Wireless” section and enroll the terminal by selecting one of the
following:
• Shock sensor, allows you to enroll an Air2-IR100 detector
• Magnetic contact, allows you to enroll Air2-MC100 magnetic reed con-
tact
• Terminal T1 M.C., allows you to enroll the “T1” terminal of an Air2-
MC100
• Terminal T2 M.C., allows you to enroll the “T2” terminal of an Air2-
MC100
• Smoke detector, allows you to enroll an Air2-FD100 smoke detector
• Magn.Cont.MC200, allows you to enroll an Air2-MC200 device.
• Curtain sensor, allows you to enroll an Air2-DT200T curtain detector
• Curtain direction, allows you to set the direction of an Air2-DT200T
• Double T. sensor, allows you to enroll an Air2-XDT200W dual technology
detector
• Single T. sensor, allows you to enroll an Air2-XIR200W passive infrared
detector
• OutdoorDetector, allows you to enroll an Air2-OTT100W outdoor triple
technology detector, an Air2-ODI100W outdoor double technology detec-
tor or an Air2-UT100 universal wireless transceiver
From SmartLeague: double-clicking on the configured terminal will open a
window where you can programme the zone.
The lower part of the window shows the “Wireless section”, right-click and
select the “Wireless” option.
Select the type of device, by means of the “Type” field, then start the
guided enrolling process by pressing the “Enroll” button.
5. For Air2 devices press the “ENROLL” key.
6. If you are enrolling and output device that is connected to a terminal of the
Air2-MC100, you must enable the “Broadcast RF” zone option in this sec-
tion.
Once done, you must step back to the configuration of the terminal and
configure it as an “OUTPUT”.
7. Enroll all the Air2-KF100 wireless keyfobs in the same way as you would
enroll ordinary proximity keys, selecting the reader with the “ADD” address.
8. Set the parameters of the zones, outputs and keypads.

18 Programming
Wireless accessories
Chapter 5
PROGRAMMING
5-1
Programming via
keypad
If you wish to carry out the programming process via keypad (parameter settings,
enrolling, deleting wireless modules, etc.), refer to the Installation and
Programming guide supplied with the intrusion control panel.
EXAMPLE To program a SmartLiving 1050 control panel which requires:
• 12 hardwired zones of which 3 on the control panel, 2 on a keypad, 7 on 2
expansion boards
• 18 wireless zones
• 5 wireless keyfobs
Minimum requirements: 18/5=4 expansion boards; if the 2 expansion boards are
for the hardwired zones assign them to addresses 1 and 2; set the Air2-BS200
DIP-microswitches to address 3 (LED DL1 Off, DL2 Off, DL3 On, DL4 On).
Enroll expansion boards 3, 4, 5 and 6 and reader 3 on the control panel.
In the “Terminals” programming section, select terminal T1 of expansion board 3
and enroll the detector. Enroll all the wireless devices consecutively.
In the “Keys-Enroll” programming section, select reader 3 then select the number
of wireless keyfobs you wish to enroll.
5-2Programming via the
Air2-BS200 module
Although some programming can be done using this method, the manufacturer
recommends that programming is carried out via the SmartLeague software or via
keypad through the Installer menu.
The available programming phases correspond to the 6 different sections in the
Programming menu. Use the buttons and LEDs on the PCB of the module to
navigate through the 6 programming phases.
1. Press the P1 button.
The programming menu will open.
2. Press the button again until access to the required phase is achieved. LED
DL3 will emit a number of blinks corresponding to the current phase.
3. Using the P2 button carry out any changes (where required). Where
required, LED DL4 will show the current data.
4. Save any changes and exit the programming session.
This can be done in two ways:
• Use the P1 button to step back.
• Press and hold the P2 button for at least 3 seconds. The 5 LEDs will light to
confirm that the data has been saved.
If this procedure is carried out during phase 2, the device will reset to factory
default settings (paragraph 5-3 Air2-BS200 module default settings
) .
PHASE 0 Stand-by: normal operating phase of the Air2-BS200 and its LED.
During this phase it is possible to exit programming and save any changes.
PHASE 1 Enroll: LED DL3 will emit in series 1 blink followed by a pause. LEDs DL1, DL4 and
PRG will remain off.
Press the “ENROLL” button on the device you wish to enroll. Press simultaneously
keys F3 and F4 on the wireless keyfob. Within 4 seconds, LED DL2 should flash to
indicate correct reception of the device and its enrollment.

Programming 19
Installation and programming manual
PHASE 2 Unenroll: LED DL3 will emit in series 2 blinks followed by a pause. LEDs DL1, DL4
and PRG will remain off.
Press the "ENROLL" button on the device you wish to unenroll (delete). Press
simultaneously keys F3 and F4 on the wireless keyfob. Within 4 seconds, LED DL2
should flash to indicate that the device has been received and unenrolled.
PHASE 3 Change transmission/reception channel: LED DL3 will emit in series 3 blinks
followed by a pause.
LED DL4 emits a number of blinks equal to the number of the current channel. 3
channels are available. Press button P2 to activate the successive channel to the
one currently operating on the Air2-BS200 module. At this point, press the
“ENROLL” button on all the detectors and sounders, access the “ENROLL” menu on
the Air keypad and press keys F3 and F4 simultaneously on all the keyfobs. This
will synchronize the system wireless devices with the new channel.
PHASE 4 Enable/Disable tamper Air2-BS200: LED DL3 will emit in series 4 blinks
followed by a pause.
LED DL4 indicates the status of this option: OFF = Tamper enabled; ON = Tamper
disabled. Press button P2 to toggle the status of this option. If the Tamper option
is disabled, the status of both microswitches will be ignored.
PHASE 5 Enable/Disable rolling-code authentication on Air2-KF100: LED DL3 will
emit in series 5 blinks followed by a pause.
LED DL4 indicates the status of this option: OFF = Rolling code authentication
enabled; ON = Rolling code authentication disabled. Press button P2 to toggle the
status of this option.
PHASE 6 Addressing: LED PRG will go On solid. LED DL1-4 indicates the current address.
Refer to paragraph 4-6 Addressing the Air2-BS200.
5-3Air2-BS200 module
default settings
To restore the factory default settings, press and hold the P2 button until the 4
LEDs (DL) come ON duringPhase 2 - Unenroll, as previously described.
5-4Options programmable
at the control panel
During the programming phase of the SmartLiving control panel you can set the
following options for the “wireless” zones:
Table 21: Wireless zones options
Option
If enabled If disabled
TampReed/FollPir
(Air2-IR100)
In order to increase battery life, the infrared
sensor will deactivate when the partitions it
belongs to are disarmed and will only activate
when the partitions it belongs to arm.
Disabled detectors cannot generate alarms. When
the partitions arm, there may be a delay of up to
3 minutes before the detector receives the
activation command.
The IR sensor is always active.
TampReed/FollPir
(Air2-MC100/MC200)
Tamper on the magnetic contact will be detected. Tamper on the magnetic
contact will not be detected.
Broadcast RF
This option must be enabled when the zone and
one of the Air2-MC100 terminals (“T1” or “T2”) is
configured as an “output”. Assures the activation/
deactivation of the output within two seconds of
the control panel command.
The activation/deactivation of
the “wireless” output occurs
within two minutes of the
command from the control
panel.
Use sensor LED
The red LED of Air2-IR100 and Air2-MC100/
MC200 devices signal alarm or tamper on the
device.
The red LED of Air2-IR100 and
Air2-MC100/MC200 devices is
always Off.
ATTENTION!
In the case of an Air2-MC100 device, this option should be enabled on
all its terminals.

20 Programming
Wireless accessories
During the control panel programming phase, the following options are available
for each device (expansion terminal, keypad or sounder) configured as wireless:
• NO Superv. WLS - If enabled, this option inhibits fault signalling in the event of
loss of wireless devices.
This option is co-related to the control panel parameter “Wireless Superv.”
“Wireless Superv.” determines the wireless-detector supervision time. When the set
time expires any detectors which do not respond will be signalled as lost.
Accepted values: 12 to 250 minutes (30 minutes at default).
•
Disable tamp. WLS - If this option is disabled, open/dislodgement tamper on Air2
devices will not generate the respective events.