INIM Electronics Air2-OTT100W Assembly instructions

1
Installation and programming manual
Air2-OTT100W
Triple technology wireless detector
for outdoor use
Installation and programming manual

2
Air2-OTT100W
Table of
contents
1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-1 About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-2 Manufacturer's details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-3 Description of the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-4 Package contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2 Functioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2-1 Detection range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2-2 Operating principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2-3 “Test” function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2-4 “Inhibition” function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3-1 Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3-2 Installation procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4 Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5 Maintenance and periodic checks . . . . . . . . . . . . . . . . . . . 9
6 Disposal and scrapping . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Appendix Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . 10
Copyright The information contained in this document is the sole property of INIM
Electronics s.r.l. No part may be copied without written authorization
from INIM Electronics s.r.l.
All rights reserved.

General information 3
Installation and programming manual
1 GENERAL INFORMATION
1-1
About this manual
MANUAL CODE DCMIINIEA2OTT100W
VERSION 1.20
1-2Manufacturer's details
Manufacturer: INIM ELECTRONICS S.R.L.
Production plant: Centobuchi, via Dei Lavoratori 10
63076, Monteprandone (AP), Italy
Tel.: [phone]
Fax: [phone]
e-mail: [email protected]
Web: www.inim.biz
The persons authorized by the manufacturer to repair or replace the parts of this
system, hold authorization to work on INIM Electronics brand devices only.
1-3Description of the product
• Wireless detector for outdoor use
• Air2 two-way wireless intrusion protection system (868MHz frequency)
• Dual PIR infrared sensors, low consumption and UV filter
• UV resistant Fresnel lens
• Low consumption, power supply range 3 to 9V
• “Test” function to signalling each alarm by LED blinking; auto power off after 4 minutes
• Tamper and dislodgement system
• Inhibition LED and transmitting function for battery life saving (always on)
• Two PIRs and one microwave (MW) programmable sensors
• AND/OR selectable function
• Mechanism for horizontal coverage adjustment
• Precision adjustment of lower beam (patented)
• Stainless steel pole brackets (not supplied)
• UV resistant polycarbonate casing
Note The manufacturer cannot guarantee the declared battery life.
Table 1: Air2-OTT100W technical features
Power-supply from 3 to 9V
Stand-by current 22μA
Maximum current 25mA
Microwave frequency 10,525GHz
Detection range from 3 to 12m
Horizontal coverage angle 60°
Horizontal coverage adjustment +/- 45°
IP protection degree IP44
Working temperature from -20° to 55°C
Dimensions 189x81x95 mm
Weight (only detector) 450g
Battery Lithium CR17450 3V (2)
Battery life 4 years

4General information
Air2-OTT100W
I I
Table 2: Mechanical parts description
A “U” shaped bracket
B “L” shaped bracket
C Hermetic casing base
D
Electronic holder
(sensors in front and
transceiver on the back)
E Cover with Fresnel lens
F
Lower PIR range
adjustment knob
G Anti tamper microswitch
H Electronics and sensors
I “O-ring” gasket
J Cover enclosure screw
K
Inner screw for “L” and
“U” brackets fixing
L
External screw for “L”
and “U” brackets fixing
M Base enclosure screw
Table 3: Electronic part description
N Terminal board for wire connection
O Red LED for radio transmission
P Yellow LED for MW
Q
Left green LED for each higher PIR
detection
R
Right green LED for each lower PIR
detection
S Jumper
T
Microwave sensitivity adjustment
trimmer
U Higher infrared sensor (PIR 1)
V Lower infrared sensor (PIR 2)
W DIP switches
X Batteries
Y Transmission green LED
Z ENROLL button
A
B
C
D
E
H
A
F
G
I
J
K L
M
M
N
U
V
O
QR
ST
W
F
Sensors
P
X
Z
Y
N
Tranceiver

Functioning 5
Installation and programming manual
The Air2-OTT100W detector communicates with INIM intrusion control panel via
the Air2 two-way wireless intrusion protection system.
1-4Package contents
Inside the package you will find:
• Air2-OTT100W detector
• Hermetic casing base
• Installing manual (this)
• Plastic bag containing:
•• 6 stainless steel metric screw M3 x 20
•• 4 anchor screws and plugs for wall mounting
•• “O ring” gasket
Items not included in the package (accessory items to be purchased separately):
•• “U” shaped brackets
•• “L” shaped brackets
2 FUNCTIONING
2-1
Detection range
ADJUSTMENT Use the trimmer “MW” (table 3, T) to adjust the microwave sensitivity (the
sensitivity is increased turning it clockwise).
By using the knob (table 2, F) it is possible to move the PIR2 (lower) in order to
obtain different ranges from 3m to 12m.
Table 4: Technical specifications of Air2 system
Operating frequency range
868.0 - 868.6MHz
selectable channels 868.1, 868.3, 868.5MHz
RF output power 25mW e.r.p.
Communication type Two-way
Modulation GFSK
Device supervision From 12 to 250 minutes
Table 5: Top view
A
Zones that can not be
covered
B
Zones that can be
covered by electronic
holder rotation
150°
60°
15°
15°
B
A
B
A

6Functioning
Air2-OTT100W
The knob moves vertically the RIP along the marked positions on the holder. Each
position corresponds to a distance:
These distances are reached when the detector is installed at about 120cm
(height).
2-2Operating principles
The detector works on the combined action of two PIRs and a microwave sensors.
The figures below shows some of most relevant working examples.
Table 6: Side view
PIR2
position Distance
A
3 m
B 4 m
C 7 m
D 10 m
E 12 m
1.2m
3m 4m 7m 10m 12m
EA
Table 7: Working examples
A Detector
B Protected area limit
C The pet is detected only by two of the three sensors (lower PIR and MW). No alarm
D The person is detected by all three sensors (upper PIR, lower PIR, MW). Alarm
E The person is detected by two sensors (upper PIR and MW). No alarm
F
If the detector is installed on a tilted wall, or pole, the detection range will be
reduced.
Both, upward as downward.
Uncorrected installation
No alarm
D EC B
A
E B
F

Installation 7
Installation and programming manual
2-3“Test” function
This function has been implemeted in order to make the detector easy to set up.
The function can be activated disconnecting and connecting again the jumper
(table 3, S); within a minute the function will be operative. In this mode the LED
will be lighted for each detection. Below the meanings of the LED's:
• Red LED (table 3, O): switch on when there is an alarm or tamper situation.
•
Yellow LED (table 3, P): switch on when the microwave detects a motion.
•
Left green LED (table 3, Q): switch on when the upper PIR detects a motion.
•
Right green LED (table 3, R): switch on when the lower PIR detects a motion.
After about 4 minutes the test mode is automatically switched off, and the LED are
deactivated (paragraph 2-4 “Inhibition” function).
Note Be sure to have screwed up the cover with Fresnel lens before perform the tests.
LEDs activation can be seen through the lens.
Once performed detection and radio transmission range tests, the detector is
ready to work.
Note LEDs are active only in test mode.
In working mode the LEDs are automatically deactivated. In order to verify if the
detector is working properly, remove the front cover disconnect and connect again
the jumper to activate the testing mode; at the end screw the cover up.
2-4“Inhibition” function
In working mode (LEDs deactivated) the function inhibition is automatically
activated in order to safe battery life. This implies that if the detector has been
installed in a populated area, the detector will no switch the alarm relay if the
detection area is free for three minutes at least.
This function avoid that the detector triggers the alarm relay continuously.
In order to verify if the detector is working properly, wait at least three minutes
after each detection.
3 INSTALLATION
WARNING It is important to evaluate the installation site previously. Bush close to the
detector might cause false alarm.
The detector is equipped with UV filters in order to avoid problems due to
sunshine rays. Anyway, if it is possible, do not direct the detector versus the sun.
3-1Placement
Start the “test” mode (paragraph 2-3 “Test” function), in order to obtain a real
simulation, keep out the protected area, and avoid any crossing into it.
After 30÷40 seconds without events, come in to the detection area and, looking
the red LED, verify if the detector works correctly.
After the detection, wait at least 7÷8 seconds before the next detection. Refer to
the coverage diagram to estimate the detection area (table 5 "Top view" and table
6 "Side view").
Environmental conditions are important elements to be evaluated during the
installation. Bump, bottomland or slops can modify the performances of the
detector.
If into the detection area any medium size animal can walk, it is suggested to
choose carefully the installation height in order to avoid false alarms.

8Programming
Air2-OTT100W
Note The maximum coverage range, 12m, is reached when the detector is installed at
about 120cm (height).
Do not obscure partially or completely the detector’s field of view.
Place the detector no less than 2m away from the Air2-BS200 transceiver.
3-2Installation procedure
1. Unscrew the screw for the cover enclosure (table 2, J).
2. Remove the cover with lens (table 2, E).
3. Unscrew the fixing screws (table 2, M) of the detector to the waterproof
rear casing.
4. Fix the hermetic casing (table 2, C) on the wall, or on a pole (be sure the
pole is stable and ripple free).
POLE FIXING 5. Fix the “L” shape bracket (table 2, B) behind the hermetic casing with one
screw (table 2, K).
Note Use the upper hole to fix the case to the “L” shaped bracket.
6. Position the two “U” (table 2, A) shaped bracket around the pole.
7. Block them with the inner screws (table 2, L) and the external screws (table
2, K).
WALL FIXING 5. Perforate the wall in correspondence of the holes on the casing.
6. Insert the wall plugs into the holes.
7. Screw up the case with the screws. Pay attention to not damage anti tam-
per switch support knock-out.
Note Use the lower hole to fix the hermetic casing on the wall.
8. Enroll the detector (refer to Air2-BS200 transceiver installation manual).
9. Insert the o-ring gasket (table 2, I) into its seat located on the electronic
holder (table 2, D).
Note Pay attention to not stretch out the o-ring gasket during its installation.
10. Couple the detector and the hermetic casing then screw (table 2, M).
11. Run the range settings (PIR 2 position adjustment, MW sensitivity, PIRs
sensitivity). See paragraph 2-1 Detection range.
12. Close the detector with the front cover with Fresnel lens as shown opposite.
13. Screw up the metric screw (table 2, J).
14. Wait 30 seconds without moving the detector.
15. Proceed with the verification and programming phases.
4 PROGRAMMING
In order to make the detector suitable for outdoor applications, a single sensor
adjustment system has been implemented.
In the tables below are shown the DIP switch configurations (table 3, W):
Table 8: Infrared sensitivity adjustment
OFF ON
DIP 1 PIR 1 sensitivity LOW PIR 1 sensitivity HIGH
DIP 2 PIR 2 sensitivity LOW PIR 2 sensitivity HIGH

Maintenance and periodic checks 9
Installation and programming manual
I
5 MAINTENANCE AND
PERIODIC CHECKS
Keep the lens clean to guarantee proper operation of the detector.
A lens which is not perfectly clean may cause detection problem.
The cleaning must be done when necessary or when clearly dirty.
CLEANING
PROCEDURE
Clean the lid and the lens with a cloth dampened with water.
Wipe with a dry cloth.
ATTENTION! Do not use chlorine-based or abrasive products or alcohol to remove particularly
noticeable dirt.
6 DISPOSAL AND
SCRAPPING
DISMANTLING 1. Unscrew the screws that fasten the front lid and remove it.
2. Disconnect the detector; disconnect all the terminals on the terminal block.
3. Divide the parts by type and dispose of them in accordance with applicable
laws.
ATTENTION! Do not dispose of the components or any other product material in the
environment.
Seek the assistance of companies authorised to dispose of and recycle waste
materials.
Table 9: Sensor programming
DIP 3
OFF ON
DIP 4
OFF
Triple AND:
MW + PIR 1 + PIR 2 Double AND: MW + PIR 2
Each techmology must
detect a motion to activate
the alarm
The detection of the MW
and the detection of the PIR
2 activate the alarm (PIR1
disabled)
ON
Double AND:
MW + PIR 1 AND of: MW + (PIR1 OR PIR2)
The detection of the MW
and the detection of the PIR
1 activate the alarm (PIR2
disabled)
The detection of the MW
and the detection of one of
the PIRs activate the alarm

10 Declaration of conformity
Air2-OTT100W
Appendix
DECLARATION OF
CONFORMITY
Deutsch: Hiermit erklärt INIM Electronics s.r.l., dass sich das Gerät Air2-
OTT100W in Übereinstimmung mit den grundlegenden Anforderungen und den
übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
ǩȢȓȋȈȘșȒȐ: ǹȕȈșȚȖȧȡȍȚȖ INIM Electronics s.r.l. ȌȍȒȓȈȘȐȘȈ, ȟȍ Air2-OTT100W
ȖȚȋȖȊȈȘȧ ȕȈ șȢȡȍșȚȊȍȕȐȚȍ ȐȏȐșȒȊȈȕȐȧ ȐȌȘțȋȐȚȍ ȗȘȐȓȖȎȐȔȐ ȐȏȐșȒȊȈȕȐȧ ȕȈ
ǬȐȘȍȒȚȐȊȈ 1999/5/ǭǹ.
ƪNJNJdžnjLjljƾ: ƳİǍǎȺNJLjıNjǗǐ ĮǑIJǗǐ ıǑNjNjǎǏijǙnjİIJĮLj Njİ IJdžnj ƪǑǏǔȺĮLjljǀ ƳįdžDŽǁĮ 1999/
5/ƪƮ
Español: Por la presente, el INIM Electronics s.r.l declara que este "producto"
cumple con la requisitos esenciales y otras disposiciones relevantes de la Directiva
1999/5/CE.
Français: Par la présente, INIM Electronics s.r.l. déclare que l’appareil Air2-
OTT100W est conforme aux exigences essentielles et aux autres dispositions
pertinentes de la directive 1999/5/CE.
Dansk: Undertegnede INIM Electronics s.r.l. erklærer herved, at følgende udstyr
Air2-OTT100W overholder de væsentlige krav og øvrige relevante krav i direktiv
1999/5/EF.
Magyar: Ez a berendezés megfelel az európai 1999/5/EC irányelvnek.
Malti: Hawnhekk, INIM Electronics s.r.l., jiddikjara li dan Air2-OTT100W
jikkonforma mal-řtiœijiet essenzjali u ma provvedimenti ořrajn relevanti li hemm
fi d-Dirrettiva 1999/5/EC.
Islenska: Hér með lýsir INIM Electronics yfi r því að Air2-OTT100W er í samræmi
við grunnkröfur og aðrar kröfur, sem gerðar eru í tilskipun 1999/5/EC.
Italiano: Con la presente, INIM Electronics s.r.l. dichiara che questo Air2-
OTT100W è con-forme ai requisiti essenziali ed alle altre disposizioni pertinenti
stabilite dalla direttiva 1999/5/CE.
Lietuviž: Šiuo INIM Electronics s.r.l. deklaruoja, kad šis Air2-OTT100W atitinka
esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas.
English: Hereby, INIM Electronics s.r.l., declares that this Air2-OTT100W is in
compliance with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
Nederlands : Hierbij verklaart INIM Electronics s.r.l. dat het toestel Air2-OTT100W in
overeenstemming is met de essentiële eisen en de andere relevante bepalingen van
richtlijn 1999/5/EG.
Norsk: INIM Electronics s.r.l. erklærer herved at utstyret Air2-OTT100W er i
samsvar med de grunnleggende krav og øvrige relevante krav I direktiv 1999/5/
EF.
Polski: Niniejszym INIM Electronics s.r.l. deklaruje Īe Air2-OTT100W jest zgodny
z zasadniczymi wymaganiami i innymi wáaĞciwymi postanowieniami Dyrektywy
1999/5/EC.
Português: Eu, INIM Electronics s.r.l., declaro que o Air2-OTT100W cumpre os
requisitos essenciais e outras provisões relevantes da Directiva 1999/5/EC.
Româna: Prin prezenta, INIM Electronics s.r.l., declarăcăaparatul Air2-OTT100W
este în conformitate cu cerinĠele esenĠiale úi cu alte prevederi pertinente ale
Directivei 1999/5/CE.
Svenska: Denna utrustning är i överensstämmelse med de väsentliga kraven och
andra relevanta bestämmelser i Direktiv Försäkran om över 1999/5/EC.
Slovenski: INIM Electronics s.r.l. izjavlja, da je ta Air2-OTT100W v skladu z
bistvenimi zahtevami in drugimi relevantnimi doloþili direktive 1999/5/ES.
The declaration of conformity may be consulted at: www.inim.biz/dc.html

11
Installation and programming manual
Notes

12
Air2-OTT100W
Centobuchi, via Dei Lavoratori 10
63076 Monteprandone (AP) Italy
Tel. [phone] _ Fax [phone]
[email protected] _ www.inim.biz
ISO 9001 Quality Management
certified by BSI with certificate number FM530352
DCMIINIEA2OTT100W-120-20171222