INIM Aria Assembly instructions

1
Installation and programming manual
Aria
Wireless keypad
Installation and programming manual
EN 50131-1
EN 50131-3
EN 50131-5-3
EN 50130-4
EN 50130-5
INCERT
CEB T031

2
Aria Wireless keypad
Table of
contents
Chapter 1 General information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1-1 About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-2 Manufacturer's details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1-3 Air2 System Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Chapter 2 Keypad description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Chapter 3 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3-1 Power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3-2 Wall-mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
3-3 Enrolling keypads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
3-4 Programming via Aria keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Chapter 4 Use of device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4-1 Operating statuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4-2 Backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
4-3 “Rolling-code” authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
4-4 Info/setup menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Appendix A Declaration of conformity . . . . . . . . . . . . . . . . . . . . . . . . . 10
Appendix B Information about disposal of batteries and accumulators . . 11

General information 3
Installation and programming manual
Chapter 1
GENERAL INFORMATION
1-1About this manual
MANUAL CODE DCMIINE0A2ARIAV8
VERSION 1.10
COPYRIGHT The information contained in this document is the sole property of INIM
Electronics s.r.l. No part may be copied without written authorization from INIM
Electronics s.r.l.
All rights reserved.
1-2Manufacturer's details
Manufacturer: INIM Electronics s.r.l.
Production plant: Centobuchi, via Dei Lavoratori 10
63076, Monteprandone (AP) - Italy
Tel.: [phone]
Fax: [phone]
e-mail: [email protected]
Web: www.inim.biz
The persons authorized by the manufacturer to repair or replace the parts of this
system have authorization to work on INIM Electronics brand devices only.
1-3Air2 System Description
The Air2 two-way wireless intrusion protection system (868MHz frequency)
integrates directly with all models in INIM intrusion control panel range.
Note In order to comply with the EN 50131-1 standards the alarm system supervision time
must be below 120 minutes.
For secure deployment and operations of the Air2 wireless intrusion protection
system, it is necessary to refer to the Installation and programming guide of the
hardwired intrusion control panel in use.
Table 1: Technical specifications of Air2 system
Operating
frequency
range
868.0 - 868.6MHz
868.7 - 869.2MHz
selectable primary channels 868.1, 868.3, 868.5MHz
selectable secondary channels 868.9, 869.1MHz
Communication type Two-way
Modulation GFSK
Device supervision from 12 to 250 minutes

4Keypad description
Aria Wireless keypad
Chapter 2
KEYPAD DESCRIPTION
The Aria wireless keypad provides all the necessary functions for control and
management of a SmartLiving installation equipped with an Air2 system, which it
can interface with through the Air2-BS200 transceiver. It integrates all the
functions of a hard-wired keypad and provides a graphic icon display.
It is equipped with an accelerometer which provides both anti-tamper and
“wakeup” from stand-by functions, whereas the brightness sensor controls the
display and key brightness optimally with respect to the surrounding environment.
Moreover, it has an automatic shutdown function in the event of loss of wireless
connection.
Aria is also equipped with a connector which allows hardwiring connection if
required.
FUNCTIONS • Communicates with Air2-BS200 transceiver @ 868MHz
• Backlit graphic display
• Icon Easy4U interface
• Programmable backlight
• Brightness sensor
• 4 indicator LEDs
•Signalbuzzer
• Inertial tamper protection
• Accelerometer controlled “Wakeup” function
• Mounts to “503” outlets
• Attaches to wall bracket or counter support
• 6 -20V ancillary power connector
• “Rolling-code” authentication
Table 2: Technical specifications
Battery type
CR17450 Lithium battery - 3V -
2200mAH, 2
estimated life 2 years
“Low battery” fault voltage Less than 2.4V
Ancillary power supply
6 - 20 V
Current draw during standby
80μA
maximum 50mA
Operating
environmental
conditions
temperature
from -10°C to +40°C
relative humidity 93% without condensation
Dimensions (W x H x D) 140 x 115 x 27mm
Weight 255g
Security rating 2
Environmental class II
ACE type
(Ancillary Control Equipment)
A
Number of Aria keypads supported by
Air2-BS200
Maximum 4

Keypad description 5
Installation and programming manual
Table 3: Description of parts
A Display
B Brightness sensor
C LED
D
Ancillary power
connector
E Battery switch
F
Battery
compartment
cover
G Cover screws
H Counter support
I
Wall bracket
support
J Screw location
K Backlocking grips
L
Mounting screw
location
M Cable entry
A
B
C
Aria - front
L
M
KK
L
Wall bracket
H
D
I
E
J
G
F
Aria - back

6Installation
Aria Wireless keypad
Chapter 3
INSTALLATION
The Aria keypad can be mounted in two ways each of which requires a different
installation procedure:
• Counter mount, with no fixed installation point.
When using this method, it is necessary to disable the keypad tamper-signal option
on the control panel.
You can stand the keypad on flat surfaces by means of the support on the back of
the device (table 3, H).
• Wall mount by means of the wall bracket (see paragraph 3-2 Wall-mounting).
For this mode it is advisable to enable the keypad tamper-signalling option on the
control panel.
For instructions regarding keypad tamper signalling refer to the programming
manual of the SmartLiving control panel.
3-1Power supply
Power to the keypad can be supplied in two different ways:
• By means of the connector on the back of the device (table 3, D) which allows 6-20
V
• By means of two CR1745 Lithium batteries installed in the battery compartment
(table 3, F).
The battery power supply can be turned On or Off by means of the switch on the
back of the device (table 3, E).
The manufacturer cannot guarantee the declared battery life.
ATTENTION! Do not use batteries other than those indicated by the manufacturer as they may
explode.
Used batteries must be disposed in accordance with local regulations.
3-2Wall-mounting
1. Choose a suitable mounting placement.
2. Put the wall bracket on the selected placement and mark the screw holes (table
3, L
) .
3. Drill the holes.
4. If you intend wiring the device, pull the wires through the cable entry (table
3, F
) and wire up the keypad.
If you intend using the batteries, place them in the battery compartment
and put the switch in the “ON” position (refer to paragraph 3-1 Power sup-
ply
).
5. Using the anchor screws, secure the bracket to the wall.
6. Enroll the device (refer to paragraph 3-3 Enrolling keypads
) .
7. Mount the keypad to the wall bracket, by first inserting the locking grips
(table 3, K
) in place, then by pushing the keypad toward the wall then down-
ward.
8. Fasten the securing screw in place (table 3, J ) .
BATT OFF
BATT ON

Installation 7
Installation and programming manual
3-3Enrolling keypads
The SmartLiving control panel can manage up to 4 Aria keypads for each Air2-
BS200 installed. However, each control panel model supports a maximum number
of keypads which must be respected.
During the addressing phase use free addresses only and ensure that no other
keypads (Joy, Concept, NCode or Alien) are present at the address of the Aria
keypads.
Via Keypad:
1. Access the Installer menu, select “Keypads” then “ChoosePeripheral”.
2. From the list that appears select the keypad to be assigned to the wireless
function.
3. Select the “Wireless” option.
4. From the list select the wireless reader simulated by the Air2-BS200 trans-
ceiver the Aria keypad is to be associated with.
5. Access the “Enroll device” section, then select “Wireless Keypad”.
Via SmartLeague:
1. Select a keypad from the those configured in the System Tree Menu.
2. Access the keypad “Programming” section and click on the “Wireless Key-
pad” check box.
3. Click on the “Enroll” button. The enrollment process window will open.
4. From the list select the wireless reader simulated by the Air2-BS200 trans-
ceiver the Aria keypad is to be associated with.
5. Click on the “Enroll” button.
6. Click simultaneously on buttons “1” AND “3” on the Aria keypad.
This operation sends the enrollment request.
If the keypad menu appears, select “Enroll” option (paragraph 4-4 Info/
setup menu).
7. Once the device is enrolled, the Aria keypad will confirm the successful out-
come of the operation.
Via Keypad:
the keypad that generated the enrollment process will emit a confirmation
beep.
Via SmartLeague:
The software window will show a a confirmation message.
3-4Programming via Aria
keypad
The programming of the SmartLiving system can be done via Aria keypad in the
same way of any keypad connected to the control panel.
However, the programming procedure is canceled by the control panel at the
occurrence of one of the following operations:
• Unenrolling of an Aria keypad via the Aria keypad itself
• Restoring to factory data of the wireless system via an Aria keypad
• Restoring to factory data of all SmartLiving system via an Aria keypad

8Use of device
Aria Wireless keypad
Chapter 4
USE OF DEVICE
4-1Operating statuses
The Aria keypad has 3 operating statuses
•Activate
•Stand-by
• No communication
ACTIVATE During this status the keypad will be at maximum power consumption level due to
the active status of:
•Display
• Backlighting
• Signal LEDs
By means of the interface with the control panel it is possible to access the User
and installer menus and carry out the same operations that can be accessed from
other keypads on the SmartLiving system.
The keypad is not equipped with a proximity reader, voice functions, thermostat
and thermal probe.
The “active” status will hold for as long as there is activity on the keypad (keys are
being pressed or the buzzer is active). If there is no activity for 10 consecutive
seconds the status will pass from “active” to “stand-by”.
STAND-BY During this status the keypad display will be off, the signalling LEDs will be Off or
blinking, and the wireless transmission (broadcast) will be active.
The Stand-by status will hold until a key is pressed, or a remote activation occurs
(for example, the buzzer signals an Exit Time) or the keypad is moved.
NO
COMMUNICATION
During this status the display, backlight and LEDs will be off.
The keypad will enter this status when the wireless communication with the
control panel is interrupted in a continuous way. When the keypad enters this
status the “NO COMUNICATION” message will appear on the display.
The keypad will try to communicate with the control panel at one-minute intervals
in an attempt to re-establish communication.
4-2Backlighting
The backlight can be programmed from the keypad in accordance with the
measured ambient-brightness. The keypad manages two different brightness
settings:
•Day
•Night
These settings can be programmed via the “Keypad” option from the “Options”
section in the User menu.
Please note that the backlight is the most important factor with regard the
consumption of battery power.

Use of device 9
Installation and programming manual
4-3“Rolling-code”
authentication
A further guarantee of security for Aria keypad wireless transmissions are the
over-the-air random codes. These random codes allow the Air2-BS200 to
authenticate the validity of each wireless keypad transmission.
In the event of irregular wireless activity, the requested operation will not be
completed.
To reset wireless transmissions and rolling code authentication, press and hold
keys “1” and “3” simultaneously.
4-4Info/setup menu
Aria has menu of its own for the access to some information on the keypad and on
the wireless system, and for some programming functions.
The menu, in full version, has 7 options. It can be are activated by holding the
keys “1” and “3” simultaneously when the keypad has been enrolled and the
SmartLiving control panel is in maintenance status.
In the case of Aria factory data restoration, the menu is automatically activated,
but in a shortened version, showing the first three options only.
The sections of the menu are:
• Enroll - starts enrollment process
•
Keypad Info - information regarding the keypad and installation of the Air2.
1st line:
- WK: operating frequency
- Ver: firmware version of the Aria keypad
2nd line:
- SN: serial number of the Aria keypad
3rd line:
- N: number of the Aria keypad managed by the Air2-BS200
- WK: address of the Aria keypad in the control panel
- Ch: RF transmission channel, primary [X] and secondary [Y] (refer to
“secondary channel”)
4th line:
- BS: address in the control panel of the associated Air2-BS200 transceiver
- SN: serial number of the associated Air2-BS200 transceiver
•
Power Info - battery charge percentage or presence of the ancillary voltage
•
Second W Channel - selects the RF support channel which guarantees the
operating capacity of the keypad.
This channel must always be different from the primary channel used by the Air2-
BS200 transceiver.
•
Factory data - starts a restore of the factory default settings after a confirmation
request.
This procedure deletes also the keypad address on the control panel. After this the
info/setup menu will be shown in a shortened version, with the first three options
only.
•
Test RF - carries out an analysis of the primary wireless channel and shows the
average RSSI value of the signal and a value from 0-100 which indicates the
channel quality (the RF Test function is enabled only when the control panel is in
maintenance mode).
•
Update Firmware - starts the upgrade of the wireless firmware.
WK868 Ver:1.000
SN:SNSNS1
N-WK:AA Ch:X-Y
BS:BB SN:SNSNS2

10 Declaration of conformity
Aria Wireless keypad
Appendix A
DECLARATION OF
CONFORMITY
Hereby, INIM Electronics s.r.l. declares that this Air2-Aria is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC.
Declarations of Performance, Declarations of Conformity and Certificates
concerning to INIM Electronics S.r.l. products may be downloaded free of charge
from the web address www.inim.biz, getting access to Extended Access and then
selecting "Certifications" or requested to the e-mail address [e-mail] or
requested by ordinary mail.