Innotech AIO-GLEIT-12 User manual

AIO-GLEIT-12
Instruction manual
© INNOTECH Arbeitsschutz GmbH. Irrtümer, Druckfehler, technische Änderungen vorbehalten! © INNOTECH Arbeitsschutz GmbH. Errors and misprints accepted. We reserve the right to make technical changes.
DE – ACHTUNG: Die Verwendung des INNOTECH-Produkts ist erst zulässig, nachdem die
Gebrauchsanleitung in der jeweiligen Landessprache vollständig gelesen und verstanden wurde.
DE
EN – ATTENTION: Use of the INNOTECH product is only permitted after the instruction
manual has been read and fully understood in the respective language.
EN
IT – ATTENZIONE: L'utilizzo del prodotto INNOTECH è permesso solo previa lettura e
comprensione dell'intero manuale di istruzioni nella lingua del relativo paese di utilizzo.
IT
FR – ATTENTION : L'utilisation du produit INNOTECH n'est autorisée qu'après avoir
entièrement lu et compris la notice d'utilisation dans la langue du pays concerné.
FR
NL – ATTENTIE: Dit INNOTECH-product mag pas gebruikt worden nadat u de gebrui-
kershandleiding in de taal van het betreffende land gelezen en begrepen hebt.
NL
ES – ATENCIÓN: Se autorizará el uso de los productos INNOTECH una vez que se hayan
leído y entendido las instrucciones de uso en el idioma del país.
ES
PT – ATENÇÃO: O uso do produto INNOTECH apenas é permitido depois de ter lido e
compreendido na totalidade as instruções de uso na respetiva língua nacional.
PT
DK – GIV AGT: Du må først bruge et produkt fra Innotech, efter du har læst og forstået
brugsvejledningen i fuldt omfang i dit lands sprog.
DK
SV – O B S : Denna INNOTECH-produkt får inte användas förrän bruksanvisningen på
respektive lands språk har lästs igenom och förståtts.
SV
CZ – POZOR: Práce s výrobkem INNOTECH je povolena teprve po kompletním přečtení a
porozumění návodu k použití v jazyku daného státu.
CZ
PL – UWAGA: Produkty firmy INNOTECH mogą być używane dopiero po dokładnym
zapoznaniu się z całą instrukcją obsługi w ojczystym języku.
PL
SL – POZOR: Uporaba izdelka INNOTECH je dovoljena šele po tem, ko ste navodila preb-
rali v celoti v ustreznem jeziku svoje dežele in jih tudi razumeli.
SL
SK – POZOR: Produkt INNOTECH môžete používať až po prečítaní a porozumení celého
návodu na použitie pre príslušnú krajinu.
SK
HU – FIGYELEM: Az INNOTECH termékek használata csak azt követően engedélyezett,
hogy saját nyelvén elolvasta és megértette a teljes használati utasítást.
HU
TR – DİKKAT: INNOTECH ürününün kullanımına ancak ilgili ülkenin dilinde sunulmuş
olan kullanım kılavuzunun tamamen okunmasından ve anlaşılmasından sonra izin verilir.
TR
ZH – 注意：只有在仔细阅读并完全理解了当地语言的使用说明后，才能使用 INNOTECH 公司的产品。
ZH

2AIO-GLEIT-12 / Version 170516 / www.innotech.at
EN
1TABLE OF CONTENTS
[2] EXPLANATION OF ICONS 3
[3] SAFETY INSTRUCTIONS 4
[4] COMPONENTS/MATERIAL 6
[5] PRODUCT SUITABILITY/APPROVAL 6
[6] INSPECTION 7
[7] WARRANTY 8
[8] SIGNS & MARKINGS 8
[9] DIMENSIONS 9
[10] INSTALLATION TOOLS 9
[11] INSTALLATION 10
[12] LOAD DIRECTIONS 12
[13] STORAGE/DISPOSAL 12
[14] DEVELOPMENT & SALES 13

3
EN
AIO-GLEIT-12 / Version 170516 / www.innotech.at
2EXPLANATION OF ICONS
Supplementary information/instructions
Warning/danger information
For an IMMEDIATE threat of danger that can cause
serious physical injuries or death.
üCorrect Incorrect
For a POTENTIALLY dangerous situation that can cause
serious physical injuries or death.
For a POTENTIALLY dangerous situation that could lead to minor
physical injuries and damage to property.
DANGER
WARNING
CAUTION
Comply with manufacturer information/ instruction manual.
Wear gloves!
Wear safety spectacles!

4AIO-GLEIT-12 / Version 170516 / www.innotech.at
EN
3SAFETY INSTRUCTIONS
3.1 GENERAL INFORMATION
- The fall protection system may be installed and used only by people who:
• are trained in the use of "personal protective equipment" (PPE),
• are in good physical and mental health. (Medical conditions such as
cardiovascular problems, intake of medicines, consumption of alcohol,
etc. negatively aect the safety of the user.),
• are familiar with the locally applicable safety regulations.
- During installation/use of the fall protection system, the respective accident
prevention regulations (e.g. working on roofs) must be complied with.
-A plan must be available that species rescue procedures for all possible
emergencies.
- Before starting work, ensure that no objects can fall to the ground from the work
site. The area below the work site (pavement, etc.) must be kept clear.
- You should plan, install and use the fall protection system in such a way that no
one can fall over the edge if the personal protective equipment is used properly
(See planning documents at www.innotech.at).
- The fall protection system is subject to maximum limit values. These are found on
the rating plate of the fall protection system, and must not be exceeded.
- When accessing the fall protection system, you must document the positions of the
anchorage devices by means of plans (e.g. top view of the roof).
- After a fall and the resulting load, the use of the fall protection system must be
stopped, and it must be checked by a specialised expert (component parts,
attachment to the substructure, etc.).
- Do not make any changes to the fall protection system.
- If you provide the fall protection system to external contractors, their understanding
of this instruction manual must be conrmed in writing.
- If the fall protection system is sold to other countries, the instruction manual must
be provided in the respective national language.
- Comply with the customary national provisions for lightning protection.
The following safety instructions and the current state of the art must be taken
into consideration.

5
EN
AIO-GLEIT-12 / Version 170516 / www.innotech.at
3SAFETY INSTRUCTIONS
3.2 FOR FITTERS: FOR SAFE ASSEMBLY
3.3 FOR USERS: FOR SAFE USE
- Ensure that stainless steel does not get in contact with swarf or steel tools, as this
can lead to corrosion.
- All stainless steel bolts must be greased with a suitable lubricant before installation.
-The tters must ensure that the substructure is suitable for fastening the fall protec-
tion system. If in doubt, consult a structural engineer.
- The roof covering must be properly sealed in accordance with applicable guidelines.
- Document the professional attachment of the fall protection system to the building
structure with dowel logs and photos of each tting situation.
- Attachment to the fall protection system is made by means of INNOTECH sliders
(e.g. AIO-GLEIT-10, -11, -12, -13 or -20). Use the INNOTECH slider only in com-
bination with the original carabiner, the INNOTECH "ALLinONE" horizontal lifeline
system, and personal protective equipment complying with EN 361 (safety harness)
and EN 363 (fall arrest system).
- The minimum free space necessary under the edge is calculated as follows:
Manufacturer's specication of the personal protective equipment used, including
deection of the cable + body height + 1 m safety margin.
- For horizontal use, only those fasteners may be used that are suited for this purpose
and have been tested for the respective edges (sharp edges, trapezoidal sheets,
steel girders, concrete, etc.).
- Correct use of the individual elements including personal protective equipment
must be ensured, because otherwise the safe functioning of the fall protection sys-
tem is NOT guaranteed.
- Do not use fall protection systems if wind speeds exceed normal parameters.
- If used on sloping roofs, roof avalanches (ice, snow) must be avoided by means
of suitable devices to intercept snow.
- You must set up secure access to the slider ("parking position for slider").
If uncertainties arise during installation, it is imperative that you contact
the manufacturer.

6AIO-GLEIT-12 / Version 170516 / www.innotech.at
EN
4COMPONENTS/MATERIAL
Comply with the manufacturer information for the personal
protective equipment used.
5PRODUCTSUITABILITY/APPROVAL
DANGER TO LIFE from incorrect use.
- Use INNOTECH "AIO-GLEIT-12" ONLY for personal safety.
- Use INNOTECH "AIO-GLEIT-12" ONLY in combination with
• INNOTECH "ALLinONE" horizontal lifeline system and
• INNOTECH original carabiners and
• personal protective equipment as per EN 361 (safety harness) and
EN 363 (fall arrest system).
-NEVER hang loads to the INNOTECH "AIO-GLEIT-12" which are NOT
expressly approved in this instruction manual.
A) Instruction manual
B) INNOTECH "AIO-GLEIT-12": stainless steel, AISI 304
C) INNOTECH "TRIPLE-LOCK CARABINER": stainless steel, AISI 304
D) INNOTECH "GAP REFERENCE GAUGE": Stainless steel, AISI 304
INNOTECH "AIO-GLEIT-12" has been tested and certied in accordance with
EN 795:2012 TYPE C.
The notified authority participating in the type test:
DEKRA EXAM GmbH, Dinnendahlstrasse 9, D-44809 Bochum, Germany
INNOTECH "AIO-GLEIT-12" is part of the INNOTECH "ALLinONE" horizontal lifeline
system, and is characterised by resistance-free passage along the stainless steel cable.
INNOTECH "AIO-GLEIT-12" is above all suitable for overhead systems and is used
as a mobile anchorage point for 1 person.
!
DANGER
Safety harnesses and lanyard lengths must be matched to the respective structure, and
must satisfy the applicable standards.
Every person working in areas where there is a danger of falling must pay attention
to the fall height.
The connection to the anchorage device must be kept short in order to limit free fall.
B C
AD

7
EN
AIO-GLEIT-12 / Version 170516 / www.innotech.at
6.1 TO BE CHECKED BEFORE EACH USE
6INSPECTION
The inspection intervals are found in the test log.
If there are any doubts concerning the reliable operation of the fall
protection system, it must NO longer be used, and must be checked
by an expert (written documentation).
If necessary, replace the product.
6.2 ANNUAL CHECKS
Have INNOTECH "AIO-GLEIT-12" inspected at least once each year by a specialist who is
familiar with the fall protection system. The user's safety depends on the eectiveness
and durability of the equipment.
Shorter intervals between inspections may be required, depending on the intensity
of use and the environment (e.g. in corrosive atmospheres, etc.).
Document the verication by the specialist/technician in the INNOTECH "ALLinONE"
instruction manual test logs, and keep them in the same place as the instruction manual.
DANGER TO LIFE from damage to the INNOTECH "AIO-GLEIT-12".
- INNOTECH "AIO-GLEIT-12" must be in perfect condition.
- Check that the running rollers move easily.
- Do NOT continue to use INNOTECH "AIO-GLEIT-12" any more if
• Damage or wear to its components are obvious,
• Other defects were observed (loose threaded connections, deformation,
corrosion, wear, bearing damage, tilting of the running rollers, etc.),
• Strain has occurred due to a fall.
• The product identication is illegible.
!
DANGER
Prior to every use, INNOTECH "AIO-GLEIT-12" must be checked visually for any obvious
defects.
Check the entire fall protection system's suitability for use by using the acceptance
protocol and test log.

8AIO-GLEIT-12 / Version 170516 / www.innotech.at
EN
7WARRANTY
The warranty period for manufacturing defects on all components (under normal condi-
tions of use) is 2 years from the date of purchase. The time limit is shortened through
use in corrosive atmospheres.
If there is strain (a fall, weight of snow, etc.,) the warranty claim is void for those com-
ponents that have been designed to absorb energy, or that may possibly be deformed.
For system installation and for components planned and installed
under the responsibility of specialised installation companies,
INNOTECH assumes neither responsibility nor warranty in the case of
improper installation.
8SIGNS & MARKINGS
A) Name or logo of the manufacturer/reseller: INNOTECH
B) Type designation: AIO-GLEIT-12
C) Signs stating that instructions in the manual
must be followed:
D) Maximum number of people who can be secured: 1
E) Year of manufacture and manufacturer's
serial number: JJJJ-..
F) Number of the applicable standard: EN 795:2012 TYPE C
Kurvenrollengleiter
AIO-GLEIT-12
JJJJ-..-...
max.
EN 795:2012
TYP C
A
B
C
D
F
E

9
EN
AIO-GLEIT-12 / Version 170516 / www.innotech.at
9DIMENSIONS
[mm]
69
107
127
10 O
5
60
M8
3
23
10 INSTALLATION TOOLS
[mm]
SW = 13 SW = 6

10 AIO-GLEIT-12 / Version 170516 / www.innotech.at
EN
Screw both bolts tightly using the lock nuts.
2.
11 INSTALLATION
SW = 13
2 x 18 Nm
SW = 6
Place both halves onto the INNOTECH "AIO-SEIL-30".
1.
O
8
Comply with the prescribed torque.

11
EN
AIO-GLEIT-12 / Version 170516 / www.innotech.at
11 INSTALLATION
In the closed state, the gap must NOT exceed 3 mm.
DONE!
3. Use the set screws to adjust to a gap of 3 mm.
SW = 13
SW = 6
ü
≤ 3 mm

12 AIO-GLEIT-12 / Version 170516 / www.innotech.at
EN
12 LOAD DIRECTIONS
13 STORAGE/DISPOSAL
Do NOT dispose the fall protection system in the house waste.
As per national requirements, gather together the used parts, and dispose
of them environmentally correctly.
13.1 STORAGE
13.2 WASTE DISPOSAL
Keep INNOTECH "AIO-GLEIT-12" free of grease, ice, and snow.
Keep INNOTECH "AIO-GLEIT-12" together with the personal protective
equipment.
DANGER TO LIFE when used in UNAPPROVED load directions.
- Use INNOTECH "AIO-GLEIT-12" ONLY in the approved load direction.
!
DANGER
45° 45°

13
EN
AIO-GLEIT-12 / Version 170516 / www.innotech.at
14 DEVELOPMENT & SALES
INNOTECH Arbeitsschutz GmbH, Laizing 10, 4656 Kirchham, Austria
www.innotech.at