Inseego Skyus 100 Series User manual

Quick Start Guide
SKYUS 100 SERIES

gettingstarted
4 Pin IO Connector (Power/IO)
RJ45 Ethernet Port
USB Micro-B Port
Power Button
Green Solid Normal Operation
Green Blinking Charging Battery (Off)
Blue Solid Good Battery
Yellow Solid Mid-Level Battery
Red Solid Low Battery
Red Blinking System Error
White Blinking Startup/Software
Update In Process
Primary Cellular Antenna
Auxiliary Cellular Antenna

gettingstarted
GPS
Off (No Color) GPS Turned Off
Yellow Blinking Searching
Green Solid Fix Obtained
Wireless, Wi-Fi/Bluetooth
Green Solid Wi-Fi On (Bluetooth Off)
Blue Solid Bluetooth On (Wi-Fi Off )
Green/Blue
Alternate Blinking Wi-Fi On, Bluetooth On
Blue Fast Blink Bluetooth Pairing Mode
Mobile Network
Green Solid Connected, Good Signal, No Traffic
Green Blinking Connected, Good Signal, Traffic
Yellow Solid Connected, Medium Signal, No Traffic
Yellow Blinking Connected, Medium Signal, Traffic
Magenta Solid Connected, Poor Signal, No Traffic
Magenta Blinking Connected, Poor Signal, Traffic
Red Solid No SIM, SIM Error, SIM Lock, No Service

devicesetup
SETTING UP YOUR DEVICE
To set up and activate the device :
1. Insert a 4FF SIM card into the SIM slot (located under the battery in the battery
compartment).
2. Contact your wireless service provider to activate the SIM card and data plan.
3. Connect the device to a power supply and ensure that the device is turned on.
* NOTE: If using the power cable make sure it is connected to a supported power source.
For complete information about your device, accessories, and safety and regulatory
information, visit www.inseego.com/iot-gateways/ or www.inseego.com/support/

deviceconnect
CONNECTING TO YOUR DEVICE
To connect a device to Wi-Fi:
1. Connect the device via the appropriate power source.
2. Ensure that the device is powered on.
3. Connect the device using the SSID and Wi-Fi password printed on the label on the
bottom of the device. The default SSID is in the format SKYUS-XXXX.
* NOTE: To pair with a Bluetooth device or network, please see the see the Skyus 100
Series User Guide.

customizesettings
USING THE EMBEDDED WEB INTERFACE TO CUSTOMIZE SETTINGS
You can access and customize your Skyus 100 Series device settings from the
embedded Web Interface.
To configure the settings of your Skyus 100 Series device:
1. Browse to http://my.skyus/ or 192.168.1.1 on any connected device to access the
device Web Interface Home page.
2. Click Sign In.
3. Use the login credentials from the labels on the bottom side of your device to log in.
4. View device health, device information, cellular information, and connection status
from the home page.
5. Select Settings from the menu to access hotspot, device, mobile, and advanced
settings options.
For more information, visit http://www.inseego.com/support

devicefeatures
SKYUS 100 SERIES - PRODUCT FEATURES
• Reliable, Industrial Grade LTE Connectivity, Wi-Fi, and GPS
• Flexible Data Options
• RJ45, USB, Serial over USB, Wi-Fi, BT [select models only]
• Flexible Power Options
• Power over Ethernet (POE or POE+ Source Required)
• Power over USB (Min. 5V @ 1A Required)
• AC Power (6-32 VDC Required)
• Battery Power (4400 mAh, Up to 12 Hrs Run Time)
• Embedded connection management, cloud connectivity, and edge processing
• Networking and Security
• Port Forwarding, Port Filtering, NAT, IPPT, VPN PT, DHCP Server, DMZ Host, etc.
• Inseego IoT Connect
• Secure Cloud-Based Device Management, Custom Alarms, Alerts, and Dashboards
For more information, visit http://www.inseego.com/support

STANDARD ACCESSORIES / CONTENTS
• Skyus 100 Series Device
• 4400 mAh Rechargeable Battery
• Whip Antennas
• AC or DC Power Cable
OPTIONAL ACCESSORIES
• Whip, Mag Mount, Bulkhead Mount, and Adhesive Mount Antenna Options Available
• USB Cable
• USB AC Adapter
• USB to Serial Adapter
deviceaccessories

INSTRUCTIONS
1. Install a #4 or #6 screw for the keyhole (1) into mounting surface
of at your desired mounting location. Note: Use a screw type that
is appropriate for the selected mounting surface (and anchors if
needed).
2. Ensure the head of the screw for (1) is kept approx. 1/8”From
mounting surface.
3. Install the device onto the screw with hole (1).
4. Install screws through holes (2) and (3) into the mounting
surface to securely fasten the device.
Use this drawing as a mounting template
for your Skyus 100 series device
52mm (2.05 in)
77mm
(3 in)

© 2018 Inseego Corp. All rights reserved. Complying with all copyright laws is the responsibility of the user.Without limiting
the rights under copyright, no part of this document may be reproduced, stored in or introduced into a retrieval system, or
transmitted in any form or by any means (electronic, mechanical, photocopying, recording or otherwise), or for any purpose
without the express written permission of Inseego Corp.
Inseego, the Inseego logo, SKYUS and the SKYUS logo, are trademarks or registered trademarks of Inseego Corp. in the
United States.
MKT-00031 Rev 3