Insportline ProfiGym C95 User manual

1
USER MANUAL –EN
IN 9306 Home Gym inSPORTline ProfiGym C95

2
CONTENTS
PARTS LIST........................................................................................................................................................... 3
EXPLODED-VIEW................................................................................................................................................ 5
ASSEMBLY INSTRUCTIONS.............................................................................................................................. 6
TERMS AND CONDITIONS OF WARRANTY, WARRANTY CLAIMS ....................................................... 20

3
PARTS LIST

4

5
EXPLODED-VIEW

6
ASSEMBLY INSTRUCTIONS
STEP 1
1. Attach the Base Frame (5) to the Back Base Frame (11), using two M10X120mm Hex Bolts (78), four
M10 Arc Washers (95) and two M10 Nylon Nuts (97).
2. Remove two M10X20mm Hex Bolts (84) and two M10 Washers (93) from two Weight Guide Tubes
(13).
3. Insert two Weight Guide Tubes (13) into the Back Base Frame (11), using two M10X20mm Hex Bolts
(84) and two M10 Washers (93).
4. Slide the Lower Fixed Tube (12) onto two Weight Guide Tubes (13), using two M8X15mm Hex Bolts
(88).
5. Slide two Rubber Rings (59) onto two Weight Guide Tubes (13).

7
STEP 2
1. Slide twelve Weight Plates (31) down two Weight Guide Tubes (13).
2. Slide the Selector Shaft Bushing (102) down the Selector Shaft (14) at first hole fix with the Selector
Shaft Pin (103).
3. Insert the Selector Shaft (14) into hole of the Weight Plate (31).
4. Slide the Top Weight Plate (30) down two Weight Guide Tubes (13), Insert the Weight Selector Pin
(27) into hole of desired weight.

8
STEP 3
1. Attach the Main Frame (6) to the Base Frame (5), using two M10X65mm Carriage Bolts (99), two M10
Washers (93) and two M10 Nylon Nuts (97).
2. Slide the Upper Fixed Tube (15) onto two Weight Guide Tubes (13), using two M8X15mm Hex Bolts
(88).
3. Remove two M10X20mm Hex Bolts (84) and two M10 Washers (93) from two Weight Guide Tubes
(13).
4. Attach the Upper Cross Beam (16) to two Weight Guide Tubes (13), using two M10X20mm Hex Bolts
(84) and two M10 Washers (93). Note: Attached the Upper Fixed Tube (15) to two Weight Guide
Tubes (13), and be close to the Upper Cross Beam (16).
5. Attach the Upper Cross Beam (16) to the Main Frame (6), using two M10X70mm Hex Bolts (81), four
M10 Washers (93) and two M10 Nylon Nuts (97).

9
STEP 4
1. Attach the Seat Support Frame (3) to the Main Frame (6), using two M10X70mm Hex Bolts (81), four
M10 Washers (93) and two M10 Nylon Nuts (97).
2. Attach the Front Upright Frame (2) to the Base Frame (5) and the Seat Support Frame (3), using one
M10X120mm Hex Bolt (78), one M10X100mm Hex Bolt (80), four M10 Washers (93) and two M10
Nylon Nuts (97).
3. Attach the Arm Fixing Bracket (8) and the Plate (75) to the Main Frame (6), using two M10X70mm
Hex Bolts (81), four M10 Washers (93) and two M10 Nylon Nuts (97).
4. Attach two Arms (9) to the Arm Fixing Bracket (8), using four Oil Bushings (big) (53), two ø38Xø11
Washers (91), two M10X20mm Hex Bolts (84), then insert two Quick Knobs (Short) (45) through the
two single holes on the Arm Fixing Bracket (8) to any of the holes on the C-type Plate of the Arms (9).
5. Attach the Arm Fixing U (10) to the Arm (9), using two Oil Bushings (big) (53), Stop Collar (51) and
M6x6mm Screws (90).
6. Attach the Steel Bushing (49) to the Arm Fixing U (10), using one M10X40mm Hex Bolt (82), two
M10 Washers (93) and one M10 Nylon Nut (97).

10
STEP 5
1. Attach the Leg Extension Frame (1) to the Front Upright Frame (2), using one M10X105mm Hex Bolt
(79), two M10 Washers (93) and one M10 Nylon Nut (97).
2. Attach the Left Connect Frame (18) and the Right Connect Frame (20) to the Upper Cross Beam (16),
using six Oil Bushings (small) (52), one Shaft (M16) (47), two M16 Washers (92), two M16 Nylon
Nuts (96) and two Plastic Dome Caps (58).
3. Attach the Press Arm (21) to the Left Connect Frame (18) and the Right Connect Frame (20), using six
Oil Bushings (small) (52), one Shaft (M16) (47), two M16 Washers (92), two M16 Nylon Nuts (96) and
two Plastic Dome Caps (58).
4. Insert the Quick Knob (Long) (46) through the single hole on the Press Arm (21) to any one of the holes
on the Fan-type Plate.