Insportline Profigym C50 User manual

USER MANUAL - EN
IN 7186 Home gym inSPORTline Profigym C50

1
PATRS LIST

2
PATRS LIST

3
ASSEMBLY INSTRUCTIONS
STEP 1：
：：
：
1. Attach Main Base (1) to Rear Base (2), using two M10×70mm Hex Bolts (69), four M10
Washers (78) and two M10 Nylon Nuts (81).

4
ASSEMBLY INSTRUCTIONS
STEP2：
：：
：
1. Remove two M10×20mm Hex Bolts (72) and two M10 Washers (78) from two Weight Guide
Tubes (3).
2. Insert the Weight Guide Tube (3) into the Rear Base (2), using two M10×20mm Hex
Bolts (72) and two M10 Washers (78).
3. Slide the two Rubber Rings (32) onto the two Weight Guide Tubes (3).
4. Slide the nine Weight Plates (34) down Weight Guide Tube (3).
5. Slide Selector Shaft Bushing (37) down Weight Selection Rod (27) at First hole fix with
Selector Shaft Pin (27).
6. Insert Weight Selection Rod (27) into hole of Weight Plate (34).
7. Slide Top Plate (33) down Weight Selection Rod (27), Insert Weight Selector Pin (27) into
hole of desired Weight.

5
ASSEMBLY INSTRUCTIONS
STEP3：
：：
：
1. Attach the Vertical Post (4) to the Main Base (1), using two M10×70mm Hex Bolts (69), four
M10 Washers (78) and two M10 Nylon Nuts (81).
2. Remove two M10×20mm Hex Bolts (72) and two M10 Washers (78) from two Weight Guide
Tubes (3).
3. Attach the Top Beam (5) to the two Weight Guide Tubes (3), using two M10×20mm Hex
Bolts (72) and two M10 Washers (78).
4. Attach the Top Beam (5) to the Vertical Post (4), using two M10×70mm Hex Bolts (69), four
M10 Washers (78) and two M10 Nylon Nuts (81).
5. Attach the two Single Pulley Brackets (22) to the Vertical Post (4), using two M10×65mm
Hex Bolts (70), four M10 Washers (78) and two M10 Nylon Nuts (81).

6
ASSEMBLY INSTRUCTIONS
STEP4：
：：
：
1. Attach Bench Press Arm (13)to Main Base (1)，using Shaft (25),six Oil Bushing (Small) (43),
two M16 Washers (77) and two M16 Nylon Nuts (80).
2. Insert the Left & Right Press Arms (17&18) into the Bench Press Arm (13), using two Quick
Knobs (short) (45).

7
ASSEMBLY INSTRUCTIONS
STEP5：
：：
：
1. Attach the Butterfly Extension (6) to Vertical Post (4), using two M10×70mm Hex Bolts (69),
four M10 Washers (78) and two M10 Nylon Nuts (81).
2. Tap Oil Bushing (small) (43) to Right Adjustable Plate (16).
3. Slide Right Adjustable Plate (16) onto Right Butterfly Arm (8), then insert Quick Knob (long)
(66) through the single hole on the Right Adjustable Plate (16) to any one of the holes on the
fan-type plate.
4. Attach Right Butterfly Arm (8) to Butterfly Extension (6),using two Oil Bushings (small) (43),
one M16 Washer (77) and one M16 Nylon Nut (80).
5. Attach Handle Tube (14) to the Right Butterfly Arm (8), using two Oil Bushings (big), one
M10×20mm Hex Bolt (72) and one Washer (￠45X￠11) (76).
6. Assembly Left Butterfly Arm (7) and Left Adjustable Plate (15) with same method.

8
ASSEMBLY INSTRUCTIONS
STEP6：
：：
：
1. Attach Seat Cushion Support (9) to Vertical Post (4), using two M10×70mm Hex Bolts (69),
four M10 Washers (78) and two M10 Nylon Nuts (81).
2. Attach Seat Support Post (10) to Seat Cushion Support (9),using one M10×65mm Hex Bolt
(70), two M10 Washers (78) and one M10 Nylon Nut (81).
3. Attach Seat Support Post (10) to Main Base (1), using two M10×70mm Hex Bolts (69), four
M10 Washers (78) and two M10 Nylon Nuts (81).
4. Attach Leg Extension (11) to Seat Support Post (10), using one M10×75mm Hex Bolt (68),
two M10 Washers (78) and one M10 Nylon Nut (81).
5. Insert the Foam Rod (20) into the Seat Support Post (10) and Leg Extension (11), then slide
Foam Roller (41) onto the Foam Rod (20).

9
ASSEMBLY INSTRUCTIONS
STEP7：
：：
：
1. Attach Backrest Cushion (30) onto Vertical Post (4), using two M8×65mm Hex Bolts (73)
and two M8 Washers (79).
2. Attach Seat Cushion (29) onto Seat Cushion Support (9), using four M8×15mm Hex Bolts
(74) and four M8 Washers (79).
3. Attach Arm Curl Cushion (28) to Arm Curl Frame (12), using two M8×15mm Hex Bolts (74)
and two M8 Washers (79).
4. Insert the Arm Curl Frame (12) into the Seat Support Post (10), using Quick Knob (short)
(45).