Insportline IN 724 User manual

1
USER MANUAL - EN
IN 724 Multifunction trainer inSPORTline Athlet

2
Part list
No.
description specification q'ty
1
Base frame
1
2
Rear stabilizer
1
3
Front vertical support
1
4
Upper beam
1
5
Front stabilizer
1
6
Seat support
1
7
Right butterfly arm
1
8
Left butterfly arm
1
9
Butterfly arm support
1
10
Foot plate fixing beam
1
11
Leg curler
1
12
Upper pulling bar
1
13
Lower pulling bar
1
14
Foam roller
2
15
xxx
16
Weight guidance rod
2
17
Weight protector
1450*502*1.0T 2
18
Weight selecting bar
1
19
Double pulley support
156*40*40*3T 1
20
Single pulley support
2
21
Hooking plate
1
22
Pulley fixing plate
132x40x3T 2
23
pin
D9.5x60L 1
24
selecting rod
1
25
hook
D8*80 6
26
Chain (7 links)
D4.8x18x34x248 2
27
Cross plate
2
28
Cover fixing plate with rod
4
29
Cover fixing plate
R133*30*2T 2
30
End cap for weight selecting bar
X
31
Bushing D29xD12.1x9T
4
32
foot cap
50x50x76.5x4.5t 6
33
Round plastic cap
D31.8*19L 4
34
Tool
150*45*35*5T 2
35
Square plastic cap 50x50x18.5
5

3
36
Square plastic cap 25*50*14
1
37
Round plastic cap
D25.4*D65*31L 4
38
Buffer
R23*35*35 2
39
Round buffer
D60xD26x26T 2
40
Fixing sleeve
D31.8*1.5T*30 2
41
Cable guidance
D16.5*80.5*24*32 20
42
Plastic ring for cable guidance
D16*D10.5*5.5T 20
43
foam D47*D90*250L
2
44
foam
D23*D90*165L 4
45
foam
D25.4*3.5*118L 10
46
Upper weight plate
280x100x80 1
47
Lower weight plate
370*200*42 12
48
backrest
695*280*50 1
49
seat
350*260*305*50T 1
50
Cable (weight—upper beam)
3540L 1
51
Cable (butterfly arms)
2480L 1
52
Cable (leg curler)
3540L 1
53
Weight pin
D10.5x56.5L 1
54
Weight washer
D47.5xD13x3T 1
55
Weight sleeve
D56xD27x23.2 1
56
Raised pulley D90*D10*28.5
12
57
Flat pulley
D90xD10x24 3
58
Ankle strap
295*95 1
59
Foot plate
1
60
Axle for foot plate
1
61
Rubber buffer
35*35*25 2
62
Reinforcing board 50*120*3T
2
63
Bushing
D31.8xD16.2x7t 4
64
Square hollow cap
50x50xx38x38x40L 1
65
Bushing
D18xD10x14.5 6
66
Arm curl pad
500x250x50 1
67
Arm curl support
1
68
Hand grip
1
69
Support of single pulley support
1
70
Lower butterfly
2
71
Spring knob
D56xM16x24xD8 1
72
Chain (12 links)
D4.8*18*34* 1
73
Fixing plate
80*50*3T 1
74
Screw cap M6
D28*14(M6) 18
75
Screw cap M8
D28*14(M8) 8
76
Screw cap M10
D28*17(M10) 96
77
Screw cap M12
D30*17(M12) 3
78
Rear stabilizer
1
79
Rear vertical support 1

4
80
arm support 1
81
arm pad 280*165*50T 2
82
hand grip 2
83
Back pad 380*250*50T 1
84
reiforcing tube 1
85L
left pedal support 1
85R
right pedal support 1
86 cylinder
D38*432L
2
87
pedal 340*170*72 2
88
buffer D33*D44*41.5 2
89
round cap D50.8x16L 2
90
square end cap 30*60*17 2

5
CHECK LIST IN PACKAGE:
M10
M8
M6
M12

6
SCREW LIST:

7
INSTRUCTION ASSEMBLY:
STEP 1.
FIG1
(1) Fix the rear stabilizer(2) and 2 weight guidance rods(16) by using 2 flat
washers(101), 2 bolts(115) and 2 foot caps(32).
(2) Fix the rear stabilizer and base frame(1) by using reinforcing board(62),flat
washer(101),nylon nut(102) and bolts(104).
(3) Fix the foot plate fixing beam (10) and front stabilizer(5) by using reinforcing
board(62),flat washer(101),nylon nut(102) and bolts(104), and then assemble the
foot cap(32)and round plastic cap(33) to the foot plate fixing beam(10).
(4) Fix the base frame and front stabilizer by using the fixing plate(73),flat
washer(101),bolts(103 & 100) and nylon nut(102).

8
STEP 2.
FIG2
(1)Fix the front vertical support(3), base frame(1) and hooking plate(21) by using 2
nylon nuts(102), 4 flat washers(101),and 2 bolts(104).
(2)Assemble the cross plate (27), 2 round buffers(39) from the bottom , then assemble
12 lower weight plates(47) and 1 upper weight plate(46) through the weight
guidance rod(16). Insert the weight selecting bar(18) through the hole of weights and
fix the weight sleeve(55) down from the upper weight plate(46) by using the weight
pin(53) and the weight washer(54). Finally put the cross plate(27) and 2 fixing
sleeves(40) on the upper bottom of the weight guidance rod(16).
Please noted: the weight pin (53) through the weight sleeve (55) at the first top hole
of weight selecting bar（18）.
The parts of weight pin (53), weight pin (53) and flat washer (54) all needed
otherwise you can’t use the upper weight plates separately.

9
STEP 3
FIG3
(1) Assemble the upper beam(4) onto the front support(31), weight guidance rod by
using 3 square plastic caps(35), then sequentially with 2 bolts(104), 4 flat
washers(101), 1 reinforcing board, 2 nylon nut(102); 2 bolts(115), 2 flat
washers(101), and then fix the rubber buffer onto the front vertical support(3).
(2) Fix the support of single pulley support(69) to the front vertical support by using 1
bolt(114),2 flat washers(101) and 1 nylon nut(102).

10
STEP 4
FIG4
(1) Fix the butterfly arm support (9) to the upper beam(4) by using 1 bolt(113), 2 flat
washers(106), 1 nylon nut (107) and 2 bushings(31).
(2) Insert axle for foot plate(60) into foot plate, and then assemble the foot plate to the
foot plate beam(10) by using 2 bolts(115), 2 flat washers(101).