Intamsys FUNMAT HT User manual

QUICK START GUIDE PN：320-0205 REV: P02
1/ 8
FUNMAT HT QUICK START GUIDE
Remove The Packaging
Unpack the printer and accessories trays from the cardboard box, and then take out the printer
and accessories trays. Gently place the printer on a flat, solid and sturdy platform.
STEP 1: Connect the power cable and
power on your printer.
STEP 2: Lower down the build plate by
clicking “Settings” →“Other
Settings”→“Buildplate to the bottom.”
Reminder: Please keep all packaging materials for warranty purpose.

QUICK START GUIDE PN：320-0205 REV: P02
2/ 8
Install The Printer
STEP 1: Power off the printer. Use the Allen
key and socket wrench to remove the four
screws to free the X & Y axis.
STEP 2: Install the motor on top of the
extruder, and ensure the upper PEEK tube is
securely inserted into its position.
STEP 3: Disassemble the nozzle set cover,
connect the motor connector to P7 on the
pin board. and fix the cables with a cable
tie.
STEP 4: Assemble the nozzle set again.
STEP 5: Open the front door to put the
glass plate onto the platform. Align the
three magnets on the glass plate to the
magnet holders on the platform.

QUICK START GUIDE PN：320-0205 REV: P02
3/ 8
STEP 6: Power on the printer.
NOTE: All maintenance work must be performed in power off mode.
Set Up The Printer
Install The Filament
Go back to the main menu, click “Material
→“Load Material”, then refer to the
instruction and the right images to ensure
that the filament is installed correctly.
Bed Leveling
There are two methods for bed leveling:
Manual leveling and Auto leveling.
Manual Bed Leveling
STEP 1: Click “Buildplate”on the display
of the printer.

QUICK START GUIDE PN：320-0205 REV: P02
4/ 8
STEP 2: Select “Manual Level”. Have the
leveling card with thickness of 0.2mm ready
and then start the bed leveling process.
STEP 3: There are three screws below the
build plate for manual bed leveling.
STEP 4: Tighten the center screw of the
build plate and use leveling card to
measure the distance between the nozzle
and the plate. Ensure the distance is
adjusted to exactly 0.2mm. Slip the leveling
card between the nozzle and plate until you
feel a little resistance. Repeat the same
operation for the left and right sides.
NOTE: For some printing works which need to heat the chamber, please firstly set the
chamber to the printing chamber temperature and keep it for at least 30min before leveling.
And do bed leveling at this high temperature.

QUICK START GUIDE PN：320-0205 REV: P02
5/ 8
Auto Bed Leveling
STEP 1: Verify the auto leveling sensor is
healthy. Go back to the main menu, click
“Settings” →“Other Settings” →
“Test” →”Leveling sensor”. The nozzle
will be heated up. Wait for approx. 2
minutes, follow the instruction on the
screen, use a removal tooling to touch the
hot nozzle, and then lift the nozzle
approx.1mm up. It will show message “The
leveling sensor is triggered”.
NOTE: IF the leveling sensor doesn’t
work, do not perform the auto
leveling function, the nozzle may
break the glass!
NOTE: Do not touch the hot nozzle to avoid burns.
STEP 2: Go back to the main menu, and
click “Buildplate” →“Level-Sensor
Calibrate”. Follow the instruction to
complete the calibration. The nozzle
heating temperature depends on the
selected material.

QUICK START GUIDE PN：320-0205 REV: P02
6/ 8
NOTE: Do not touch the hot nozzle to avoid burns.
STEP 3: Click “Auto Level”, printer will
automatically finish the auto leveling
process without any human interference.
Firstly, the machine will preheat the
buildplate and chamber, then preheat the
nozzle. The heating temperature follows
the material selected. Once reached the
set temperatures, the printer will start
auto leveling. The printer shows “Auto
level successfully” once auto leveling is
done. The printer is ready to print now.
Auto-Level Frequency
Auto level frequency has two options:
1. Always off
2. Before every print
If you choose “Always Off”, it means the
printer will not take auto-level before print.
If you choose “Before Every Print”, it
means the printer will take auto-level before
every print.

QUICK START GUIDE PN：320-0205 REV: P02
7/ 8
Install Software
After successfully setting up the printer, locate the SD card and install the INTAM-SUITE
software on your computer. It is available for Windows, Mac OSX and Linux.
Camera Guide
To connect the camera please follow the Camera User manual in your box. You can install
the App of the camera on your smartphone or computer.
Schematic View
01 Display Screen
07 Build Plate Screw
13 Camera (Inner The Corner)
02 Push/Rotate Button
08 Heat Fan
14 Power Switch
03 SD Card Slot
09 Door Handle
15 Power Socket
04 Print Head
10 Spool Holder
16 USB Socket
05 Build Plate
11 Handle
06 Build Plate Holder
12 FilamentAbsent Sensor
03
13
09
10
12
11
14
15
16
08
04
05
01
02
08
07
06

QUICK START GUIDE PN：320-0205 REV: P02
8/ 8
User Manual
You can find the softcopy of User Manual from the SD card. It is also available on our
website, please download it from below link https://www.intamsys.com/3d-printer-manuals/
Warranty
1 year Warranty, please provide the Series No. to your local reseller for warranty.
Support
For more information or technical support please visit: www.intamsys.com/support/ (or
contact nearby reseller)