WANHAO MARK II Duplicator 6 Plus User manual

you can
WANHAO Duplicator 6 Plus
MARK I I
USER MANUAL

Table of Contents
A. Welcome to WANHAO D6 Plus
A1. The wanhao experience
A2. Specications of the WANHAO D6 Plus
B. Get started and unpack your WANHAO D6 Plus
B1. Unboxing your WANHAO D6 Plus
B2. What’s in the box
B3. WANHAO D6 Plus at a Glance
C. Installing parts on your WANHAO D6 Plus
C1. Installing power supply
C2. Installing lament: spool holder and guide
C3. Switch on/off the WANHAO D6 Plus
D. First use of your WANHAO D6 Plus
D1. First time startup
D 2 . L e v e l i n g t h e b u i l d p l a t e
D3. Loading lament material
D4. Make your rst 3D print
D 5 . 3 D P r i n t i n g a n d p r i n t r e m o v a l
E. Make a print le with Cura software
E1. Downloading and installing Cura
E2. Cura software interface
E3. From YouMagine.com to load le in Cura
E4. Preparing a 3D model
E5. From SD-card to print your le
F. Maintenance for your WANHAO D6 Plus
F1. In General
F2. Change lament and material feeder
F3. Lubricating the axes
G. Troubleshooting and support for the WANHAO D6 Plus
G1. Simple Troubleshooting tips
G2. Contact support
G3. Terminology
G4. Safety and Compliance
Repair and Refurbished Goods or Parts Notice
Table of content User manual
4
5
6
7
8
12
13
14
15
16
17
18
19
20
22
24
25
26
27
28
30
31
32
33
34
35
36
37
38
40
41
42
43
44
NOTES
2

WELCOME
TO THE
WANHAO
D6 PLUS
D6 PLUS
3

WELCOME
TO THE
A1. The WANHAO Experience
This User manual is designed to help you start your
experience with D6 Plus. Within these pages, we want to
show you how simple and easy it is to produce great prints.
You might be familiar with earlier types of WANHAO or other
3D-printers. It is essential that your read this manual carefully
as there are a lot of new procedures with WANHAO D6 Plus.
The wanhao experience Welcome to the D6 Plus 4

A2. Specication of the D6 Plus Welcome to the D6 Plus
5
Primary Attributes
of the Technology
FDM Type Printer, Fully assembled. Entry Level
Desktop Home Printer.
Software CURA, Repetier Host, Simplify 3D, & Others
Extruder System MK11 Extruder with Full Metal Hot End
Material Support PLA, PVA, PC, PETG, ABS, Most Other Filaments
Bed Leveling Auto bed leveling,Manual leveling
Max Printable Area 200*200*180mm
Filament Diameter/Light 1.75mm
Max Printing Speed 70mm/S
Case Material Steel Case
With Enclosure? Optional
Extruder Quantity 1
Accuracy X 0.0125mm
Y 0.0125mm
Z 0.005mm
Material Cost USD12-34
Net Weight(kg) 20kg
Gross Weight(kg) 22kg
Packing Size(cm) 46x46x55cm
Plateform Holder Steel frame holder
Layer Thickness 100 micron- 400 micron
Rail Locking System Steel Locking Frame
Print Bed Type Aluminum Plate, Heated
Resume Printing Can Resume Printing After Power failture
LCD Display English/Chinese or Customize Any Language
Power Supply Internal 110V or 250V(optional), 50/60Hz, 4.0A
(Input), Uses Standard IEC Cable
Typical Application •A perfect printer for educators who intend to
use the printers in technical education.
•Great printer for DIY Hobbyist.
Technical Specications

GET STARTED &
UNPACK YOUR
WANHAO
D6 PLUS
D6 PLUS
6

7
B1. Unboxing your D6 Plus
1. Place the D6 Plus box on a stable
surface, Placing it centrally on the  oor
will provide the best accessible position
for unpacking.
2. Open the box. Here you will see
the User Manual.
We recommend that you use the User
manual to guide you through the
setup process  rst
3. Remove black foam protector
4. Lift the printer gently up with 2 hands
on the top frame of D6. You may need one
person to help to hold the box still.
NOTE: You can download a PDF copy of
this User manual under manual at the
support page
B1. Unboxing your D6 Plus Get started & unpack your D6 Plus
5. Position the printer on a sturdy table to
optimise the approach and with plenty of
space surrounding it.
NOTE: Please do not use excessive force
when unpacking your D6 Plus. Excessive force
may lead to damage to the D6 Plus and its
components.

6. Remove the plastic bag from the top of
the printer.
7. Cut the 2 black bindings from the side
of the printer.
8.Pull the lament box out from the
Printer gently.
9. Pull the Wanhao Masking mat out
from the printer gently.
8
B1. Unboxing your D6Plus Get started & unpack your D6 Plus
10. Pull the Spare parts box out from
the printer gently.

11. Wrap the protection foam and pull it
out from the printer
12.. Cut the X axis rail secure binding
right at front top of printer.
13. Cut the Y axis rail secure binding
14. Get printer out from the bottom foam
cave. You will find the push button is not
installed. We place it inside the spare parts
box.
15.Find the push button from the repairing
box.
9B1. Unboxing your D6 Plus Get started & unpack your D6 Plus

16.Loose the locking bolt by 1.5mm
hex wrench anti-clockwise.
17.Turn the control button pillar at
side upward.
10
B1. Unboxing your D6 Plus Get started & unpack your D6 Plus
18. Insert the button onto the pillar.
Make sure the bolt hole is right
towards the at pillar side.
19.To lock the button by turning the
bolt clockwise with 1.5mm hex wrench

B2.What’s in the box
Besides your D6 supplied with SD card in the 3D printer, there are a lot of
essential accesoires that comes with this 3D printer. All the following parts should
be in the box, please check contents.
Filament spool Spool holder Tweezers Power supply cable
USB cable (only for
 rmware update)
Hex wrenches
11 B2. What’s in the box Get started & unpack your D6 Plus
Card reader
Memory Card
Print Bed Mats Scrape

1
2
3
4
567
1. MK11 extruder
2. Leveling Sensor
3. WANHAO printing mat
4. Super thick Guiding Rod
5. SD card slot
6. LCD Display
7. Navigation Dial
8
9
10
11 12
8. Cable Quick Coupler
9. Cable locker
10. Extruder Cable
11. USB Socket
12. Power switch
13
13. Power Socket
B3. D6 Plus at a glance
12
B3. D6 Plus at a Glance Get started & unpack your D6 Plus

INSTALLING
PARTS
WANHAO
D6 PLUS
D6 PLUS
ON YOUR
13

C1. Installing power supply
Attaching power supply
Now the next step is to give the D6 plus power. This is done by attaching the
internal power supply.
1. First make sure the power switch is in the
OFF position, this is when the button at the
back is pressed to [0].
2. The corresponding power cable(for your
country) have to be inserted into the Power
supply socket at back of printer. The at side of
power plug has to face towards the right of the
D6.
3. The connector has to be inserted at the back
of the D6 plus, in the round hole next to the
on/off switch and USB slot. The at side of the
power plug has to face towards the top of the
D6 plus.
4. Now plug the internal power supply into the
wall socket.
Detaching the power supply
1. If the power supply has to be detached, the
first step is to make sure the D6 plus turned
off. This is done by pressing the power
switch to 0.
2. Next take the power plug out of the wall
socket.
3. The plug has a sliding collar. When removing
the plug from the machine, gently slide the collar
outwards which will release the plug and allow it
to come out with ease.
CAUTION: Please make sure not to pull the
cable. Excessive force may result in breaking this
component.
4. The main plug can be detached by pulling it
out gently.
14
C1. Installing power supply Installing parts on your D6 plus

C2.Installing lament: spool holder
Attaching the spool holder
1. Turn the Z axis screw clockwise to
raise the platform.
2. Install the spool holder. Insert the
M30 nut from the printing chamber
into the Hex cave.
3. One hand hold the nut and the other
hand Insert the holder from outside into
the nut and turn the holder clockwise
until it’s tight.
Detaching the spool holder
4.Turn the spool holder anti-clockwise
to get holder detached from the printer.
5.Get the M30 nut detached from the
inside of printer.
15 C2. Installing lament spool holder Installing parts on your D6 plus
Note: the wrench mark on the nut
toward 2 clock direction.

C3.Switch on/off the D6 Plus
Switch off the D6 plus
The on/off button (a.k.a. ‘ – | O ’) of the
D6 Plus is located at the back. The ‘ O ’
represents off and the ‘ – ’ represents on.
When it’s switched to the ‘ – ’ the D6 Plus is
turned on and should start up.
After the D6 plus has been turned on, the
front LED display should light up and the
sides should glow.
Switch off the D6 plus
The D6 plus can be turned off by
pressing the power switch to ‘ O ‘ at any time, it
is recommended to only turn off the
D6 plus when it is NOT in use.
When the D6 plus is switched off, the
display and lights will automatically turn
themselves off.
16
C3. Switch on/off the D6 Plus Installing parts on your D6 plus

FIRST USE
WANHAO
D6 PLUS
D6 PLUS
OF YOUR
17

D1. First time startup
This chapter guides you through the steps and the rst run of the D6 plus. After you switch on
your D6 plus, the display will light up and guide you through .
Use of the display
1.
You can navigate through the display by using the button. This button can be
pushed and rotated. By rotating you can select or control an action. By pushing
you can conrm an action. When pushing the button you hear a “beep” sound to
conrm your chosen action. A blinking button means the D6 is waiting for
user input.
2.
Navigate to [MAINTENANCE],
[ADVANCED] and conrm for a
[Factory reset] You can use this
function for the rst run wizard
at any time
3.
When you read this step, Click
the [AUTO BED LEVELING]to go
the next step: To level the bed
automatically.
18
D1. First time startup First use of your D6 pLUS

D2.Leveling the build plate
19 D2. Leveling the build plate First use of your D6 Plus
By click the [AUTO BED LEVELING], the printer would start sensing 9 different spot on the
building plate and record the offset data. All the leveling procedure would be  nished automatically.
NOTE: After transportation you might want to level your build plate to ensure your 3D models
stick well to the build plate
NOTE: Before proceed anything ,use a soft fabric to Wipe off the dusts from the building plate
surface and clean it.
.