Integral LED ILBTX001 User manual

Thank you for purchasing an INTEGRAL LED product. When installed correctly this unit will provide years of service – with no lamp
changes required. For support or warranty information please see integral-led.com. Always turn o circuit power at the distribution
unit before installation and maintenance. Please ensure that the power cannot be connected inadvertently.
Important Details – Please read prior to installation
Ensure the AC/Mains power is NOT connected and cannot be unexpectedly reconnected during installation.
1. This product must be installed by a qualied electrician in accordance with instructions provided and in compliance with recognised
electrical and safety regulations relevant to the country it is being installed.
2. This product is suitable for installation on surfaces with normal ammability e.g. wood, masonry. It is not suitable for use on highly
ammable surfaces or in ammable atmosphere.
3. This product must be securely xed to the mounting surface using the xings clips, screws and wall plugs supplied.
The screws and wall plugs are suitable for “masonry” only. Other xings are not supplied and must be purchased.
4. Please use the cable gland supplied in the box if the LED batten is required to be linked.
5. Connect the power lead to a suitable junction box to maintained IP rating.
6. Recommended cable H05RN-F 3x1.00mm².
7. Please use the protective cover on any unused connector.
8. Maximum no of units in series is 10 using recommended cable.
9. This product is not suitable for dimming.
IMPORTANT! This product is a Class II device. However an earth connection is required.
Warranty
This unit carries a 5 year warranty from the date of purchase, providing that it has been installed correctly and not modied in any way. Should a
fault occur please contact the original place of purchase.
Important Notes
Operating and storage of luminaire must be within rated temperature and humidity guidelines. Operation must be within rated input voltage.
• Keep away from strong electromagnetic radiation sources and protect from lightning strike.
• Should the unit malfunction, return to distributor or reseller. No user serviceable parts inside. Risk of electric shock, do not disassemble or
INSTALLATION INSTRUCTION
Integral LED Toughshell+ IP66 batten
5 Year Warranty
EN
70,5 29 600/1200/1500/1800
658/1258/1558/1858
60,5
6
8
66,5
Product code Description
ILBTX001 4FT 20W 3000LM 4000K 120° 150lm/W Non-Dimmable
ILBTX002 5FT 30W 4500LM 4000K 120° 150lm/W Non-Dimmable
ILBTX003 6FT 35W 5250LM 4000K 120° 150lm/W Non-Dimmable
ILBTX004 4FT EM3HR 20W 3000LM 4000K 120° 150lm/W Non-Dimmable
ILBTX005 5FT EM3HR 30W 4500LM 4000K 120° 150lm/W Non-Dimmable
ILBTX006 6FT EM3HR 35W 5250LM 4000K 120° 150lm/W Non-Dimmable
ILBTX007 4FT MW 20W 3000LM 4000K 120° 150LM/W Non-Dimmable
ILBTX008 5FT MW 30W 4500LM 4000K 120° 150LM/W Non-Dimmable
ILBTX009 6FT MW 35W 5250LM 4000K 120° 150LM/W Non-Dimmable
ILBTX021 4FT 38W 5700LM 4000K 120° 150LM/W Non-Dimmable
ILBTX022 5FT 53W 7950LM 4000K 120° 150LM/W Non-Dimmable
ILBTX023 6FT 60W 9000LM 4000K 120° 150LM/W Non-Dimmable
ILBTX024 4FT EM3HR 38W 5700LM 4000K 120° 150LM/W Non-Dimmable
ILBTX025 5FT EM3HR 53W 7950LM 4000K 120° 150LM/W Non-Dimmable
ILBTX026 6FT EM3HR 60W 9000LM 4000K 120° 150LM/W Non-Dimmable
ILBTX027 4FT MW 38W 5700LM 4000K 120° 150LM/W Non-Dimmable
ILBTX028 5FT MW 53W 7950LM 4000K 120° 150LM/W Non-Dimmable
ILBTX029 6FT MW 60W 9000LM 4000K 120° 150LM/W Non-Dimmable
ILBTX041 4FT 20W 3000LM 3000K to 5700K 120° 150LM/W Non-Dimmable
ILBTX042 5FT 30W 4500LM 3000K to 5700K 120° 150LM/W Non-Dimmable
ILBTX043 6FT 35W 5250LM 3000K to 5700K 120° 150LM/W Non-Dimmable
ILBTX061 4FT 38W 5700LM 3000K to 5700K 120° 150LM/W Non-Dimmable
ILBTX062 5FT 53W 7950LM 3000K to 5700K 120° 150LM/W Non-Dimmable
ILBTX063 6FT 60W 9000LM 3000K to 5700K 120° 150LM/W Non-Dimmable
ILBTX081 4FT 26W/32W/38W - 3900LM/4800LM/5700LM 4000K 120° 150LM/W Non-Dimmable
ILBTX082 5FT 43W/49W/53W - 6450LM/7350LM/7950LM 4000K 120° 150LM/W Non-Dimmable
ILBTX083 6FT 48W/54W/60W - 7200LM/8100LM/9000LM 4000K 120° 150LM/W Non-Dimmable

Connection-Electrical installation
Ceiling type
Suspending type
Warranty/Technical and contact
information are all available at
www.integral-led.com
* Requires suspension kit ILBASK091 supplied separately
Step 1: Rotate and remove round cap on the side.
Step 2: Pull out connector/terminal.
Step 3: Power cord go through the round cap, inserted into corresponding
terminal holes.
Step 4: Push the terminal/connector back into xture, put on the the round
cap and rotate it to lock position.
Step 5: Wire the other side by repeat procedure 1-4, to reach connection
through wiring.
Step 1: Make a right position and screw hole on the ceiling, screw the clip on
the ceiling tightly.
Step 2: Snap the lamp into clips. The installation is nished.
Step 1: Make a right position and screw hole on the ceiling, then install the
expansion.
Step 2: Steel wire rope go through the clips, and insert into expansion.
Step 3: Snap the lamp into clips, and adjust the length of wire rope according
to need. The installation is nished.
Step 1
Step 2Step 1
Step 3
Step 2Step 1
Step 4
Step 2
Step 5
Step 3
Non-Dimmable
IP66
Integral LED is a division
of Integral Memory plc:
Unit 6, Iron Bridge Close,
Iron Bridge Business Park,
London, NW10 0UF, UK
Integral Europe BV, 2801 DG, NL
WASTE ELECTRICAL PRODUCTS SHOULD NOT BE
DISPOSED OF WITH HOUSEHOLD WASTE. PLEASE
RECYCLE WHERE FACILITIES EXIST. CHECK WITH
YOUR LOCAL AUTHORITY FOR RECYCLING ADVICE.
attempt to repair the luminaire.
• Do not install or use the luminaire if the casing is found to be broken.
• The luminaire must be installed by a qualied electrician.
• The luminaire should be positioned away from heat and vibration. Avoid contact with any corrosive chemicals.
• The luminaire should be mounted in free air it is recommended not to exceed 30° C ambient.
• Never cover the luminaire with heat insulation materials.
• The luminaire should be positioned at least 1 metre away from radios, failure to do so may aect radio reception.