Endon 68835 User manual

Cable Set Light Fitting
Safety Warnings
INSTRUCTION MANUAL
• Theseproductsareonlysuitableforconnectiontoa240V~50HzsupplyinaccordancewithcurrentIEE
wiringRegulationsandshouldbeinstalledinaccordancewithlocalBuildingRegulationsandarefor
Domesticceilinguseonly.TheyarenotsuitableforaBathroomlocation.
• Beforeinstallingyourlightttingalwaysswitchoffthemainssupplyandremovetheappropriatefuseor
switchofftheappropriatecircuitbreakerbeforecommencinginstallation.
• ThisisaClassII,DoubleInsulatedproduct ThisFittingdoesnotrequireanEarth,andLiveorNeutral
must notbeconnectedtoEarth.Theterminalblocksaresuppliedaccordingtorequirementsofthetting.
• Nevertbulbsofahigherwattagethanthosespecied,asthesemaycauseoverheatinganddamagethe
tting.
• Ifyouareinanydoubtaboutyourcompetencepleaseconsultaqualiedelectrician.
• Ifanymodicationismadeitwillinvalidatethewarrantyandmayrendertheproductunsafe.
68833_68834_68835_68836-Cable_Set-P20160104
EndonLighting,LS90SE
Assembly/ User Instructions
Before you start
Pleasereadtheseinstructionscarefullybeforettingandretainforreference.Checkthepackagingandmake
surethatyouhavealltherequiredparts.Followeachassemblystepinordertopreventincorrectassembly.
Ensurethattheproductisfullyassembledasillustratedbeforeuse.
The Light pack contains:
Lighttting.
Terminalconnectionblock(s).
Fixingpack.
The following tools may be required:
Selectionofcrossandatheadscrewdrivers.
Electricdrillandassorteddrillbits.
Wirestrippers.
Electricalinsulationtape.
These assembly diagrams are intended as a guide – if in doubt consult a qualied electrician.
Care Information
Allow10minutestocoolbeforereplacing,adjustingorcleaning.
Cleanwithadryclothonly.Donotuseliquidorabrasivecleanersonthisproduct.
1. Decideonthepositionofthelighttting,orremoveexistinglighttting.Takeanoteofthepositionofthe
electricalconnections.Ensurethereisasolidmountingsurface,preferablyawoodenjoistorjoistbridgeto
supporttheweightofthelighttting.
2. Ifyouwanttoreducetheoveralllengthofthettingitisessentialthatthisisdonebeforethettingismounted
totheceilingand/orconnectedtothemainssupply.Werecommendthechainnotbemadeshorterthan
15cm.Removethechainlinksuntilthedesiredlengthisreached.Thecablemustnowbeshortenedand
theexcesscablecutandre-connectedtotheterminalblock.Feedthecableupthroughtheplasticbushand
formaloopabovetheceilingcup,movingthegureof8cablerestraintdowntheexposedcable.NOTE: The
electric cable must always be longer than the chain to prevent strain being placed on the cable. If you
are unsure about your ability to do this, we recommend you contact a qualied electrician.
3. Removethetwosidescrews(4)andretainthescrewsforre-use.Usethexingbracket(1)asatemplateto
markthescrewholes,andsecuretotheceilingwithappropriatescrewxings(2).
4. Supportyourttingandconnectthehousewiringtotheterminalblock(3)–seeexpandedwiringdetails
below.NOTE: This is a Class II tting and must not be earthed.Anylooseterminalblocks–notsecured
toceilingcup–shouldalwaysbecoveredwith2layersofgoodqualityinsulationtape.
5. Securetheceilingcupoverthebracketbyusingthescrews(4)removedinPoint2.

EndonLighting,LS90SE
6. Fitshade,ifdesired,byunscrewingtheshadering,placingtheshadeoverthelampholderandreplacingthe
shadering.
7. Fitthebulbs.NOTE: Never t bulbs of a higher wattage than those specied on the label (as these may
cause overheating and damage the tting).
8. Turnonthepowerandtest.
Assembly/ User Instructions Continued
68833_68834_68835_68836-Cable_Set-P20160104
3.Expandedwiring
diagram
4