Intel SSR316MJ2 User manual

Intel®Storage System SSR316MJ2
Backplane Board (FMJBACKPLANE)
Installation Guide
Order Number: C75951-001

Important Safety Instructions
Important Safety Instructions
Read all caution and safety statements in this document before performing any of the instructions.
See Intel Server Boards and Server Chassis Safety Information at
http://support.intel.com/support/motherboards/server/safecert.htm.
Wichtige Sicherheitshinweise
Lesen Sie zunächst sämtliche Warn- und Sicherheitshinweise in diesem Dokument, bevor Sie eine
der Anweisungen ausführen. Beachten Sie hierzu auch die Sicherheitshinweise zu Intel-
Serverplatinen und -Servergehäusen unter
http://support.intel.com/support/motherboards/server/safecert.htm.
重要安全指导
在执行任何指令之前，请阅读本文档中的所有注意事项及安全声明。 和/或
http://support.intel.com/support/motherboards/server/safecert.htm 上的
Intel Server Boards
and Server Chassis Safety Information
（《Intel
服务器主板与服务器机箱安全信息》）。
Important Safety InstructionsConsignes de sécurité
Lisez attention toutes les consignes de sécurité et les mises en garde indiquées dans ce document
avant de suivre toute instruction. Consultez Intel Server Boards and Server Chassis Safety
Information rendez-vous sur le site
http://support.intel.com/support/motherboards/server/safecert.htm.
Instrucciones de seguridad importantes
Lea todas las declaraciones de seguridad y precaución de este documento antes de realizar
cualquiera de las instrucciones. Vea Intel Server Boards and Server Chassis Safety Information en
http://support.intel.com/support/motherboards/server/safecert.htm.
WARNINGS
Storage system power on/off: The push-button on/off power switch on the
front panel of the storage system does not turn off the AC power. To remove
AC power from the storage system, you must unplug the AC power cord
from either the power supply or wall outlet.
Hazardous conditions—power supply: Hazardous voltage, current, and
energy levels are present inside the power supply enclosure. There are no
user-serviceable parts inside the power supply; servicing should only be done
by technically qualified personnel.

Intel®Storage System SSR316MJ2 Backplane Board iii
Hazardous conditions—devices and cables: Hazardous electrical
conditions may be present on power, telephone, and communication cables.
Turn off the storage system and disconnect telecommunications systems,
networks, modems, and the power cord attached to the storage system before
opening it. Failure to do so can result in personal injury or equipment
damage.
Avoid injury: Lifting the storage system chassis and attaching it to the rack
is a two-person job. If needed, use an appropriate lifting device. A fully
loaded Intel®Storage System SSR316MJ2 weighs approximately 31.8 kg (70
lbs.).
CAUTIONS
Temperature: The operating temperature of the storage system, when
installed in an equipment rack, must not go below 5 °C (41 °F) or rise above
35 °C (95 °F). Extreme fluctuations in temperature can cause a variety of
problems in the storage system.
Ventilation: The equipment rack must provide sufficient airflow to the front
of the storage system to maintain proper cooling. It must also include
ventilation sufficient to exhaust a maximum of 1900 BTUs per hour for a
fully loaded Intel®Storage System SSR316MJ2.
Disclaimer
Information in this document is provided in connection with Intel®products. No license, express or implied, by estoppel or
otherwise, to any intellectual property rights is granted by this document. Except as provided in Intel's Terms and Conditions
of Sale for such products, Intel assumes no liability whatsoever, and Intel disclaims any express or implied warranty, relating
to sale and/or use of Intel products including liability or warranties relating to fitness for a particular purpose, merchantability,
or infringement of any patent, copyright or other intellectual property right. Intel products are not designed, intended or
authorized for use in any medical, life saving, or life sustaining applications or for any other application in which the failure of
the Intel product could create a situation where personal injury or death may occur. Intel may make changes to
specifications and product descriptions at any time, without notice.
Intel is a registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.
*Other names and brands may be claimed as the property of others.
Copyright © 2004 Intel Corporation. All Rights Reserved.

iv Intel®Storage System SSR316MJ2 Backplane Board
Revision History
Date Revision
Number Modifications
Sept. 8, 2004 1.0 Initial release
Oct. 7, 2004 1.1 Minor edits
Contents
About the Backplane Board Assembly............................................................. 7
Contents..................................................................................................................................7
Backplane Board Installation Procedures........................................................ 8
Required Tools........................................................................................................................8
Power Down System and Remove Chassis Cover.................................................................8
Unseat Hard Disk Drives from Hard Disk Drive Bays .............................................................9
Remove Front Panel Cables from Front Panel Board...........................................................10
Remove Phillips Screws from System Fan Assembly...........................................................11
Remove Fan Connectors from Baseboard............................................................................12
Remove Fan Assembly from the System and SATA Cables from the Host Bus Adapter
Cards.....................................................................................................................................13
Cut the Plastic Ties that House the SATA Cables................................................................14
Remove I2C Cables from Backplane Board..........................................................................15
Remove Power Distribution Board Module Connectors from Backplane Board...................16
Remove Backplane Board from the System.........................................................................17
Install New Backplane Board................................................................................................18
Re-connect Power Distribution Board Module Connectors to Backplane Board ..................19
Re-connect SATA Cables to HBA Cards..............................................................................20
Re-connect the I2C Cables....................................................................................................21
Re-insert Fan Assembly into System....................................................................................22
Re-attach Fan Assembly to System......................................................................................23
Re-attach System Fan Assembly Connectors to Baseboard................................................24
Re-seat Front Panel Board Cables.......................................................................................25
Re-seat Hard Disk Drives in Hard Disk Drive Bays...............................................................26
Finishing Up..........................................................................................................................27
Figures
Figure 1. Removing Chassis Cover..............................................................................................8
Figure 2. Unseat Hard Disk Drives and Hard Disk Drive Carriers ................................................9

Intel®Storage System SSR316MJ2 Backplane Board v
Figure 3. Removing Front Panel Cables.....................................................................................10
Figure 4. Removing Phillips Screws to Release the System Fan Assembly...............................11
Figure 5. Removing Fan Connectors from the Baseboard .........................................................12
Figure 6. Removing System Fan Assembly and SATA Cable Connectors.................................13
Figure 7. Cutting the Plastic Ties that House the SATA Cables.................................................14
Figure 8. Removing the I2C Cables from the Backplane Board..................................................15
Figure 9. Removing the Power Distribution Board Module Connectors......................................16
Figure 10. Removing the Backplane Board from the System.....................................................17
Figure 11. Installing the New Backplane Board in the System...................................................18
Figure 12. Re-Connecting the Power Distribution Board Module Connectors............................19
Figure 13. Re-connecting the SATA Cables to the HBA Cards..................................................20
Figure 14. Re-connecting the I2C Cables....................................................................................21
Figure 15. Re-inserting the Fan Assembly into the System........................................................22
Figure 16. Re-attaching the Fan Assembly to the System..........................................................23
Figure 17. Re-attaching the System Fan Assembly Connectors ................................................24
Figure 18. Re-seating Front Panel Board Cables......................................................................25
Figure 19. Re-seating Hard Disk Drives in Hard Disk Drive Bays...............................................26
Figure 20. Re-attaching the Chassis Cover................................................................................27

vi Intel®Storage System SSR316MJ2 Backplane Board

Intel®Storage System SSR316MJ2 Backplane Board 7
About the Backplane Board Assembly
Enclosed is your new Intel®FMJBACKPLANE Backplane Board. The Intel®FMJBACKPLANE
Backplane Board comes equipped with sixteen connected SATA cables.
 NOTE
This document describes how to install the FMJBACKPLANE Backplane
Board into the Intel®Storage System SSR316MJ2.
The FMJBACKPLANE Backplane Board is installed into the storage system just behind the hard
disk drives, near the front portion of your system.
Contents
•Intel®FMJBACKPLANE Backplane Board Assembly
The FMJBACKPLANE Backplane Board Assembly consists of the following:
⎯FMJBACKPLANE Backplane Board mounted within metal housing
⎯Pre-installed SATA Cables that are already connected to the Backplane Board

8 Intel®Storage System SSR316MJ2 Backplane Board
Backplane Board Installation Procedures
Required Tools
•Cross-head (Number 1 size Phillips*) screwdriver, maximum length 4 inches
Power Down System and Remove Chassis Cover
A. From within the Intel®Storage System Console, power down your system.
B. Remove both AC Power cords from the AC Power inputs on your system. See Figure 1.
C. Loosen the two thumb screws from the top of the chassis cover. See Figure 1.
D. Facing the front of the chassis, push the top cover rearward, and then lift it up to remove it.
A
D
B
C
C
Figure 1. Removing Chassis Cover

Intel®Storage System SSR316MJ2 Backplane Board 9
Unseat Hard Disk Drives from Hard Disk Drive Bays
A. Pressing down on the hard disk drive handle release mechanisms, unlatch the handle on the
hard disk drives and hard disk drive carriers. See Figure 2.
B. Rotate the hard disk drive and hard disk drive carrier handles downward. See Figure 2.
C. Slide the hard disk drives and hard disk drive carriers at least halfway out of the hard disk drive
bays. See Figure 2. It is not necessary to completely remove the hard disk drives from the bays.
A
B
C
Figure 2. Unseat Hard Disk Drives and Hard Disk Drive Carriers
NOTE: If a hard disk is completely removed from the Storage System Console, it must be re-
installed into the exact same drive bay. Refer to the Intel®Storage System SSR316MJ2 Quick Start
User’s Guide for more details.

10 Intel®Storage System SSR316MJ2 Backplane Board
Remove Front Panel Cables from Front Panel Board
A. Remove the Primary IDE Cable labeled J5 from its receptacle on the front panel board.
See Figure 3.
B. Remove the Secondary IDE Cable labeled J3 from its receptacle on the front panel board.
See Figure 3.
C. Remove the Front Panel Cable labeled J1 from its connector receptacle on the front panel
board. See Figure 3.
D. Remove the front panel power connector from its connector receptacle on the front panel board.
See Figure 3.
ABCD
Figure 3. Removing Front Panel Cables

Intel®Storage System SSR316MJ2 Backplane Board 11
Remove Phillips Screws from System Fan Assembly
A. Using a Number 1 size Phillips Screwdriver, remove the Phillips screw on each side of the
system that holds the system fan assembly in place. See Figure 4. Set these screws aside. They
will be re-installed later.
A
Figure 4. Removing Phillips Screws to Release the System Fan Assembly

12 Intel®Storage System SSR316MJ2 Backplane Board
Remove Fan Connectors from Baseboard
A. Remove the wire connector for Fan 3 from the baseboard. See Figure 5.
B. Remove the wire connector for Fan 4 from the baseboard. See Figure 5.
C. Remove the wire connector for Fan 5 from the baseboard. See Figure 5.
A
B
C
AB
C
Figure 5. Removing Fan Connectors from the Baseboard

Intel®Storage System SSR316MJ2 Backplane Board 13
Remove Fan Assembly from the System and SATA
Cables from the Host Bus Adapter Cards
A. Simultaneously pull up on both sides of the system and remove the fan assembly from the
storage system. Set the system fan assembly on a static-free surface. See Figure 6.
B. Carefully remove the 16 SATA Cable connectors from the three SATA Host Bus Adapter
Cards near the back of the system. See Figure 6.
A
A
B
Figure 6. Removing System Fan Assembly and SATA Cable Connectors

14 Intel®Storage System SSR316MJ2 Backplane Board
Cut the Plastic Ties that House the SATA Cables
A. Cut the plastic cable ties that bundle the SATA Cables. See Figure 7.
A
Figure 7. Cutting the Plastic Ties that House the SATA Cables

Intel®Storage System SSR316MJ2 Backplane Board 15
Remove I2C Cables from Backplane Board
A. Make a note of the header positions of the three I2C Cable connectors. After installation of the
SATA Cables has been completed, you will re-connect these connectors to the same headers.
Carefully remove the I2C Cable connector labeled JP4 from its I2C Cable header on the
backplane board. Carefully remove the I2C Cable connector labeled SL2J6 from its I2C Cable
header in the HBA Card set. See Figure 8.
B. Carefully remove the I2C Cable connector labeled JP6 from its I2C Cable header on the
backplane board. Carefully remove the I2C Cable connector labeled SL3J6 from its I2C Cable
header in the HBA Card set. See Figure 8.
C. Carefully remove the I2C Cable connector labeled JP7 from its I2C Cable header on the
backplane board. Carefully remove the I2C Cable connector labeled SL4J6 from its I2C Cable
header in the HBA Card set. See Figure 8. Set the I2C Cable connectors on a static-free surface.
ABC
ABC
Figure 8. Removing the I2C Cables from the Backplane Board

16 Intel®Storage System SSR316MJ2 Backplane Board
Remove Power Distribution Board Module Connectors
from Backplane Board
A. Carefully remove the two 12-pin Power Distribution Board Module connectors from the
backplane board. See Figure 9.
A
Figure 9. Removing the Power Distribution Board Module Connectors

Intel®Storage System SSR316MJ2 Backplane Board 17
Remove Backplane Board from the System
A. Using a Number 1 size Phillips Screwdriver, remove the two Phillips screws on each side of the
system that hold the backplane board to the side of the chassis. See Figure 10. Set these screws
aside. They will be re-installed later.
B. Using a Number 1 size Phillips Screwdriver, remove the four Phillips screws from the steel lip
that holds the backplane board in place. See Figure 10. Set these screws aside. They will be re-
installed later.
C. Carefully remove the backplane board from the storage system. Pay attention to sharp edges on
the backplane board. See Figure 10.
Figure 10. Removing the Backplane Board from the System

18 Intel®Storage System SSR316MJ2 Backplane Board
Install New Backplane Board
A. Insert the new Intel®FMJBACKPLANE Backplane Board and sheet metal shroud
combined unit into the system. Align the holes on the bottom of the Backplane Board sheet
metal shroud onto the protruding blue pegs on the floor of the chassis. Snap the Backplane
Board and sheet metal shroud into place.
B. Align the screw holes on the backplane board with the screws holes on the steel lip. Using a
Number 1 size Phillips Screwdriver, screw in the four Phillips screws into the steel lip and
the backplane board until the backplane board is installed. See Figure 11.
C. Align the screw holes on the side of the chassis with the screws holes on the backplane
sheet metal shroud. Using a Number 1 size Phillips Screwdriver, screw in the two Phillips
screws into each side of the system until the backplane board is installed. See Figure 11.
Figure 11. Installing the New Backplane Board in the System

Intel®Storage System SSR316MJ2 Backplane Board 19
Re-connect Power Distribution Board Module
Connectors to Backplane Board
A. Carefully re-connect the two 12-pin Power Distribution Board Module connectors to the
backplane board. See Figure 12.
A
Figure 12. Re-Connecting the Power Distribution Board Module Connectors

20 Intel®Storage System SSR316MJ2 Backplane Board
Re-connect SATA Cables to HBA Cards
A. Carefully re-connect the 16 SATA Cable connectors to the three SATA Host Bus Adapter
Cards. Ensure that the SATA Cables are routed to the outside of the Host Bus Adapter
Cards. See Figure 13.
B. Insert new plastic cable ties through the steel links on the side of the chassis where the
SATA Cables are normally routed. Bundle the SATA Cables in the same way they were
originally bundled and snap the ties tight into place around the cables. Wrap new plastic
cable ties around the SATA Cables in the other spots where the original plastic cable ties
were cut, and snap the ties tight into place around the cables. See Figure 13. A total of
seven new plastic cable ties should be used. Route the SATA Cables along the side of the
chassis in the same way that the original SATA Cables were routed. The cables remain on
the chassis side of the Host Bus Adapter Cards and connect to the cards from the chassis
side.
B
B
B
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
A
Figure 13. Re-connecting the SATA Cables to the HBA Cards