Intellian i2 User manual

i2
Installation and Operation
User Manual
Document Number: 2012D0-UM1004-V1_0

2
Intellian Satellite TV Antenna Systems
Intellian i2 Serial Number
This serial number will be requested for all troubleshooting or service Inquiries.
Notice
All Right Reserved
Intellian i2®and Intellian®are the registered trademarks of Intellian Technologies, Inc., and should not be appropriated without permission by Intellian Technologies, Inc., and the
information contained in this manual is the property of Intellian Technologies, Inc. Any and all parts of this manual shall not be reproduced and distributed in any form without
prior written consent by Intellian Technologies, Inc. The information contained in this manual shall be subject to change at any time without notice due to the functional upgrade
of the product.

3
INTRODUCTION
INTRODUCTION TO INTELLIAN i2
FEATURES OF INTELLIAN i2
BASIC SYSTEM CONFIGURATION OF INTELLIAN i2
INSTALLATION
SYSTEM COMPONENTS
TOOLS REQUIRED FOR INSTALLATION
PLANNING THE INSTALLATION
INSTALLATION AND MOUNTING OF ANTENNA
INSTALLING THE ACU
ACU DIMENSIONS
SELECTING ACU INSTALLATION SITE
CONNECTING THE SYSTEM CABLES
CONNECTING THE SYSTEM TO A GPS
ADJUSTING THE LNB SKEW ANGLE (LINEAR POLARIZATION ONLY)
OPERATION INSTRUCTION
INTRODUCTION
OPERATING USING THE ACU
ACU SOFT KEYS
NORMAL MODE
SETUP MODE
OPERATION USING PC CONTROLLER PROGRAM
INTRODUCTION
PROGRAM INITIALING AND SERIAL PORT SETUP
MAIN MENU
CONTROLLER MENUS
PREPARATION FOR TRANSPORTATION
WARRANTY
APPENDIX : TECHNICAL SPECIFICATION
INTELLIAN i2
4
4
5
6
7
7
10
11
14
17
17
18
19
22
23
24
24
25
25
25
28
49
49
50
51
52
61
62
63
64
Table of Contents

4
Intellian Satellite TV Antenna Systems
Introduction to Intellian i2
Intellian i2 is a digital satellite antenna system designed specically
for all types of vessels (Anchored or transit) to automatically identify,
track and capture satellite signals from the Digital Video Broadcasting
(DVB: the international standard for digital TV transmissions) compatible
satellites.
Specically, Intellian i2 has Wide Range Search (WRS) algorithm, which
minimizes the search time during initialization, and Dynamic Beam
Tilting (DBT) technology, which dynamically shapes the antenna beam
to utilize stabilization. While tracking the target satellite, DBT technology
uses a high-performance, constantly adjusting sub-reector which
allows the antenna to remain relatively still, eliminating the constant
whine of stepper motors while staying locked onto the satellites.
For simplicity and savings, the i2 brings you hassle-free installation
with its single cable design between the antenna and the control unit.
For exibility, there is a second RF connector on the antenna base.
In addition, the i2 has adopted a built-in GPS interface (NMEA 0183,)
allowing boaters to plug-in an external GPS to speed up acquisition
time.
Introduction

5
Features of Intellian i2
Enjoy satellite broadcasts at sea
Intellian i2 is the most modern antenna system that enables you to
receive high quality broadcasting signals at sea where the atmospheric
and environmental conditions are very harsh.
Fully automatic control system
The fully automatic control system allows you to simply turn the power
switch on, and have crystal clear, high quality satellite television in
motion or at anchor.
High quality antenna
High tech parabolic antenna technology has been adopted for this
antenna system, which is optimal for marine conditions. This enables
you to receive the optimal signal level even when it is raining or
snowing.
Fast and efcient search for the satellite
The WRS (Wide Range Search) algorithm allows for the antenna system
to search the satellite within the shortest amount of time and to detect
the satellite signal under any position and within any directional
movement of the ship.
Outstanding reliability
Intellian i2 provides highly reliable system through the implementation
of a modularized design and the usage of strictly proven components.
Easy installation
Intellian i2 uses only one RF cable for installation. This makes
installation easy. Power, RF, and Data signals transfer from the antenna
to the ACU through this single cable.
Compact size
Intellian i2’s small and compact size is perfect for small vessels.

6
Intellian Satellite TV Antenna Systems
Basic System Conguration of Intellian i2
For your satellite TV system to function properly, the system will have to
be connected with all of the provided components as shown on the right
(Refer to the next chapter ‘Installation’ in this manual for more detailed
connection instructions). Separate purchase of a satellite receiver and a
TV is required.
Figure 01 : Basic Conguration with 2 Receivers
ANT RF1
FUSE
FG - +
+ -
TV
(Not Supplied)
Antenna Control Unit
DC Power on Vessel
(DC - 9.0 - 30.0V)
NMEA GPS
PC( Not Supplied)
Satellite Receiver
(Not Supplied)
NMEA
RECEIVER
DC 9~30V PC INTERFACE
TV
(Not Supplied)
Satellite Receiver
(Not Supplied)
Note: Dish Network and Bell TV users please refer to the Intellian Dish
Network MIM Installation and User Manual.

7
The components of the Intellian i2 have been designed to be modular so
that it is suitable for simple installation on all types of vessels.
System Components
Antenna Unit
The antenna of Intellian i2 is comprised with the following components
for optimum search and reception of the satellite signal.
• Mechanical Unit – manipulates the antenna to receive an optimal
satellite signal regardless of the movement of the vessel.
• Control Unit – controls mechanical operation of the antenna.
• RF Unit – transmits an optimum satellite signal to the receiver.
• Radome – protects the antenna from severe marine environmenta
Installation
Figure 02 : Radome

8
Intellian Satellite TV Antenna Systems
Antenna Control Unit (ACU)
The Antenna Control Unit (ACU) provides the power to the antenna
and controls various settings of the antenna. The digital VFD (Vacuum
Fluorescent Display) allows for easy operation of the ACU, even in the
dark.
The functions of the ACU are as follows:
• Provides power to the antenna unit
• Monitors the antenna status
• Changes the target satellite
• Set up the user environment
• Set the current GPS information
• Set satellite information
• Perform self-diagnosis of the antenna
• Set up the interface with a PC
Figure 03 : Front & Rear of ACU
NMEA
ANT RF1 RECEIVER
FUSEDC 9~30V PC INTERFACE
FG - +
+ -
Front
Rear
Antenna Control Unit

9
Hex.Bolt
5
Flat Washer
5
Spring Washer
5
Hex. Nut
5
Item
Qty
Item
Qty
Size
Self-Tapping Screw
5
(M4 X 16L)
Machine Screw
5
(M3 X 8L)
Antenna
ACU
Installation Kit
Contains the items required for securing the antenna unit and ACU to the
vessel.
Other Components
No Components Size Qty
1ACU Bracket - 2
2RG6(Antenna – ACU RF Cable) 15m 1
3RG6(ACU – IRD Cable) 3m 1
4Power Cable 10m 1
5PC Serial Cable 1.8m 1
6NMEA Connector 1.5m 1
7Power Connector AK950-2 1
8
Hex Bolt
M6x35L 5
M6x50L 5
Tapping Screw ø4x16L 5
ø3x8L 5
Flat Washer M6 10
Spring Washer M6 5
Nut M6 5
9Installation CD - 1
10 User Manual - 1
11 Mounting Template 1
12 Quick Installation Guide - 1
Figure 05 : List of the Supplied Parts
Figure 04 : Installation Bolt Kit

10
Intellian Satellite TV Antenna Systems
Tools Required for Installation
Figure 06 : Required Tools for Installation
Power Drill 11 mm Spanner
Cross-Head
Screwdriver 10 mm Spanner
8 mm Drill Bit
Ø50 mm
Hole Saw
Pencil
Power Drill 11 mm Spanner
Cross-Head
Screwdriver 10 mm Spanner
8 mm Drill Bit
Ø50 mm
Hole Saw
Pencil

11
15°
Planning the Installation
Selection of Installation Site
Install the antenna in accordance with the following procedures to
ensure maximum performance of the antenna.
The antenna should be installed in a place where it has an all-round
clear view of the horizon. Please be sure there are no obstacles within
15 degrees above the antenna. Any obstacles can prevent the antenna
from tracking the satellite’s signal (Refer to the drawing on the right).
Do not install the antenna nearby the radar, especially if their on the
same plane, as their energy levels may overload the antenna’s front-end
circuits. It is recommended to position the antenna at least 4 feet (1.2m)
above or below the level of the radar and a minimum of 15 feet (4.6m)
away from any high power short wave radars.
The mounting platform should be rigid enough and not subjected to
excessive vibration. The movement of the antenna can be minimized by
installing it at the center of the vessel. For optimal performance of the
antenna, it is not recommended to install it at any corner of the vessel,
where the movement of the vessel is the greatest. Install the bottom
of the antenna parallel to the surface of the sea and x it tightly to the
structure of the vessel.
When setting the antenna down, be careful not to damage the RF
connector. Striking the connectors on the bottom directly will damage
the connector.
Figure 07 : Elevation Limit of Obstacles
Antenna unit Obstacle

12
Intellian Satellite TV Antenna Systems
Cables
Before installing the system’s cables, consider the following points.
• All cables need to be well clamped and protected from physical
damage and exposure to heat and humidity.
• A cable with an acute bend is not allowed.
• Where a cable passes through an exposed bulkhead or deckhead, a
watertight gland or swan neck tube should be used.
Power Requirements
You need to follow the power requirements to avoid damaging the
system.
• Intellian i2 has been designed to work on a boat’s power supply rated
at 12V / 24V DC (acceptable range: 9~30 V DC).
• If your IRD(s) and television(s) require a 110V/240V AC power supply,
you will need to install a suitable DC to AC converter to operate the
unit(s) from your boat’s DC power supply.
Extending the cables
The cables that have been supplied with your Intellian system should be
of adequate length to complete the installation on most boats.
Power Cable
This cable is supplied at a length of 10m.
RF Cable
This cable is supplied at a length of 15m. If a longer length is required
you should replace this cable with an extended RF cable supplied by
Intellian Technologies.
Note: Exceeding the indicated cable lengths will result in reduced
performance of your system.

13
Installation and Mounting of the Antenna
The method of installation and mounting of antenna may vary due
to vessel design but the following procedures are applicable in most
situations, and will result in a secure and effective installation.
Conrmation of Size and Installation of Power Tower
• Conrm the height and diameter of the bottom surface of the antenna
before installing it.
• The space must be sufcient for installing the antenna unit
considering the height and diameter of the antenna.
• The height and the diameter of the bottom surface of the antenna are
as shown in the following drawing. If possible, install the antenna
using a power tower.
Note: Before installing the antenna, open the radome and remove the
shipping constraints from the antenna interior. Reinstall the radome
before operating the system. The system will not perform properly if the
radome is open.
Figure 08 : Radome Dimension of i2
Ø37 cm (14.7”)
38.1 cm (15”)

14
Intellian Satellite TV Antenna Systems
Marking of the Antenna’s Parking Position
Referring to the Mounting template, mark where antenna is to be
mounted onboard the ship (it must be a at surface) or on a separate
power tower by drawing a square of 14.4cm (5.7”)
Figure 09 : Intellian i2
Note: If a power tower is not used to mount the antenna, separate
cable shocks and waterproong measures must be taken to protect the
RF connector from being exposed to sea water and external shocks. An
exposed cable may cause electric shock and cause serious damage to
the equipment.
14.4cm (5.7”)
14.4cm (5.7”)

15
Securing Holes for Bolts and Cable Ways
Make 4 bolt holes of 8mm diameter, one at each corner of a rectangle
drawn as below, and make a circular hole of 50mm diameter at the
center of the rectangle through which the cable will run.
Connection of the Cable
Remove the rubber cap from RF connector. Connect the RF cable to the
RF connector under the base plate through the access hole using an
11mm spanner. Be careful not to over tighten, as you may damage the
connector.
Figure 11 : Connectors on Bottom of Antenna
Note: Do not use excessive force when using the spanner, this will
damage the threads. Be careful that the connectors do not contact the
mounting surface of the antenna, this may cause critical malfunction
and serious damage to the equipment.
Figure 10 : Drilling Instruction
Antenna Unit
RF1 Cable
Optional
11mm
Spanner
Ø50mm
Hole Saw
Ø 8mm
Drill

16
Intellian Satellite TV Antenna Systems
Mounting the Antenna
Fix the antenna to the holes made before as shown in the drawing
below by using the hex head bolts (M6 X 35L), M6 spring washer,
M6 at washer and M6 Nut supplied.
Figure 12 : Mounting the Antenna
ACU Dimensions
Installing the ACU
5.4 cm (2.1”)
5.5 cm (2.2”)
22.8 cm (9”)
17.8 cm (7”)
21.7 cm (8.5”)
18.5 cm (7.3”)
Figure 13 : Dimension of ACU
Radome Base
Deck
M6 Flat Washer
M6 Spring Washer
M6 Hex. Nut
10mm Spanner
M6 Flat Washer
M6 Hex. Bolt
10mm Spanner

17
Figure 14 : Installation of ACU
Selecting ACU Installation Site
The ACU should be installed below deck, in a location that is:
• Dry, cool, and ventilated.
• Easily accessible from your main TV viewing area.
To Install the ACU
1. The ACU should be installed using the two supplied mounting
brackets which allow for a top or bottom mounting conguration.
2. Using the self tapping screws supplied, attach the mounting brackets
to the sides of the ACU.
3. Place the ACU in the location where it is going to be installed.
4. Connect the cables to the rear of the ACU.
5. Use a pencil to mark the 4 hole positions (two on each side), and
use the appropriate drill bit to drill them.

18
Intellian Satellite TV Antenna Systems
Connecting the System Cables
After installation and xation of the antenna, connect the ACU to the antenna.
Refer to the drawing below to connect cables.
Single IRD Connection
• Connect the RF Cable (15m) from the RF 1 connector on the antenna
to the ANT. RF1 connector on the rear of ACU.
• Connect the ACU-IRD Cable (3m) from the RECEIVER connector on the
rear of the ACU to the RF on the IRD.
• Connect the power cable (10m) from the DC power connector on the
rear of ACU to a power source at 12V /24V DC.
• Press the POWER ON switch in front of the ACU to start operating the
antenna system automatically.
Figure 15 : Single IRD Conguration
NMEA
ANT RF1 RECEIVER
FUSEDC 9~30V PC INTERFACE
FG - +
+ -
RF1
Antenna Receiver
RF2
RF Cable ACU IRD Cable
DC Power Cable NMEA GPS PC Cable (Not supplied)
ACU IRD (Not Supplied)

19
Twin IRDs Connection
You can connect two IRDs for your antenna as shown in the following
diagram. One of the IRD’s need to be set up with the ACU in order to use
another IRD without connecting the ACU. Both IRD’s with and without an
ACU connection can receive any channels that are available from the
tracked satellite.
As in the single IRD option, the RF cables from the antenna base plate
should be connected to ‘LNB’, ‘ANT’, or ‘Satellite In’ on the rear panel of
the IRD.
Figure 16 : Dual-IRDs Conguration
NMEA
ANT RF1 RECEIVER
FUSEDC 9~30V PC INTERFACE
FG - +
+ -
Antenna Receiver
DC Power Cable NMEA GPS PC Cable
ACU
RF1 RF2
RF Cable ACU IRD Cable
IRD1 (Not Supplied)
IRD2 (Not Supplied)

20
Intellian Satellite TV Antenna Systems
Multiple-IRDs Connection
In order to connect multi-IRD to the antenna, you will need to purchase
a suitable multiswitch. The multiswitch has to be installed between the
antenna unit and the IRDs as shown on the right.
Figure 17 : Multi-IRDs Conguration
Note: The system can receive either “High Band” or “Low Band”
channels by using a multi-switch to connect more than two receivers.
RF1RF2
RF Cable ACU IRD Cable
IRD 4
Multi switch
(Not Supplied)
IRD 3
* IRD 1~4 : Not supplied
IRD 2IRD 1
NMEA
ANT RF1 RECEIVER
FUSEDC 9~30V PC INTERFACE
FG - +
+ -
Antenna Receiver
DC Power Cable NMEA GPS PC Cable
ACU