Intellian i4 Inland User manual

Global Leader in Marine Satellite Antenna Systems
i4 Inland
Installation and Operation User Guide

2
Intellian Satellite TV Antenna Systems
Serial number of the product
This serial number will be required for all troubleshooting or service inquiries.
© 2020 Intellian Technologies Inc. All rights reserved. Intellian and the Intellian logo are trademarks of Intellian Technologies, Inc.,
registered in the U.S. and other countries. The Intellian i4 Inland is a trademark of Intellian Technologies, Inc. Intellian may have
patents, patent applications, trademarks, copyrights, or other intellectual property rights covering subject matter in this document.
Except as expressly provided in any written license agreement from Intellian, the furnishing of this document does not give you
any license to these patents, trademarks, copyrights, or other intellectual property. All other logos, trademarks, and registered
trademarks are the property of their respective owners. Information in this document is subject to change without notice. Every
effort has been made to ensure that the information in this manual is accurate. Intellian is not responsible for printing or clerical
errors.
Disclaimer
The information in this user manual is subject to change without prior notice through a product life cycle. A printed version of the
user manual is periodically updated and may contain inaccuracies or omissions compared to the recent product information. The
most up-to-date information is available on our website at https://www.Intelliantech.com.
Doc. No. UG-K00221-V1.4

3
GENERAL PRECAUTIONS
INTRODUCTION
INTRODUCTION TO INTELLIAN i4 Inland
FEATURES OF INTELLIAN i4 Inland
BASIC SYSTEM CONFIGURATION OF INTELLIAN i4 Inland
INSTALLATION
SYSTEM COMPONENTS
TOOLS REQUIRED FOR INSTALLATION
PLANNING THE INSTALLATION
INSTALLATION AND MOUNTING OF ANTENNA
INSTALLING THE ACU
ACU DIMENSIONS
SELECTING ACU INSTALLATION SITE
CONNECTING THE SYSTEM CABLES
CONNECTING THE SYSTEM TO A GPS
ADJUSTING THE LNB SKEW ANGLE (LINEAR POLARIZATION ONLY)
OPERATION INSTRUCTION
INTRODUCTION
OPERATING THE ACU
ACU SOFT KEYS
NORMAL MODE
SETUP MODE
OPERATION USING PC CONTROLLER PROGRAM
INTRODUCTION
PROGRAM INITIALING AND SERIAL PORT SETUP
MAIN MENU
CONTROLLER MENUS
PREPARATION FOR TRANSPORTATION
WARRANTY
APPENDIX : TECHNICAL SPECIFICATION
4
4
4
5
6
7
7
10
11
13
16
16
17
18
21
22
23
23
24
24
24
27
48
48
49
50
52
60
61
62
Table of Contents

4
Intellian Satellite TV Antenna Systems
Introduction to Intellian i4 Inland
Intellian Inland is a 45cm digital satellite antenna system designed
specifically for only inland marine use. Intellian Inland is ideal for
virtually all types of vessels (anchored or transit) to automatically
identify, track and capture satellite signals from the Digital Video
Broadcasting (DVB: the international standard for digital TV
transmissions) compatible satellites.
Specifically, Intellian Inland has a Wide Range Search (WRS) algorithm,
which minimizes the search time during initialization, and Dynamic
Beam Tilting (DBT) technology, which dynamically shapes the antenna
beam to utilize stabilization. Once the satellite is acquired, the antenna
DBT continuously measures the heading, pitch, and roll of the vessel
by obtaining the satellite signal level around the antenna point, and
transmits commands to the antenna motors to keep the antenna pointed
at the satellite at all times. This active stabilization is enhanced by a
conical scan tracking function
to detect and lock onto the
strongest signal, resulting
in the clearest reception
possible.
The Inland has a built-in GPS
system which enhances the
speed of satellite signals
acquisitions.
Introduction
THIS WAY UP
• Place the boxes/crates on the floor noting the direction of
the arrow.
FRAGILE
• Since the Radome is fragile, handle it with care. Do not
apply excessive pressure or shock. These may cause
surface cracking or other damage.
KEEP DRY
• Always make sure the antenna is stored on a dried floor.
• The antenna can withstand ordinary rain. However it
water resistance cannot be guaranteed if submerged.
• Keep the antenna in dried place for sufficient ventilation.
Do not store the antenna wrapped in a tarp, tent, vinyl,
and others.
General Precautions
Before you use the antenna, make sure that you have read and
understood all safety requirements.

5
Features of Intellian i4 Inland
Enjoy satellite broadcasts at sea
Intellian Inland is the most modern antenna system that enables you to
receive high quality broadcasting signal at sea where the atmospheric
and environmental condition is very harsh.
Fully automatic control system
Fully automatic control system allows you to simply turn the power
switch on, and have crystal clear, high quality satellite television in
motion or at anchor.
High quality antenna
High tech parabolic antenna technology has been adopted for this
antenna system, which is optimal for marine conditions. This enables
you to receive the optimal signal level even when it is raining or
snowing.
Fast and efcient search for the satellite
The WRS (Wide Range Search) algorithm allows for the antenna
system to search the satellite within the shortest amount of time and
to detect the satellite signal under any position and with any directional
movement of the ship.
Outstanding reliability
Intellian Inland provides highly reliable system through the
implementation of a modularized design and the usage of strictly proven
components.
Built-in GPS
Intellian Inland has imbedded GPS, which allows for the system to
upload the GPS data automatically into the system for an even faster
and stable system.
Easy installation
Intellian Inland uses only one RF cable for installation. This makes
installation easy. Power, RF, and Data signals transfer from the antenna
to the ACU through this single cable.
Compact size
Intellian Inland’s small and compact size is perfect for small vessels.

6
Intellian Satellite TV Antenna Systems
Basic System Conguration of Intellian Inland
For your satellite TV system to function properly, the system will have
to be connected with all of the provided components as shown on the
right. (Refer to the next chapter ‘Installation’ in this manual for more
detailed connection instructions). Separate purchase of a satellite
receiver and a TV is required.
Figure 1 : Basic Conguration
FG - +
+ -
TV
(Not Supplied)
ACU
Adapter
( AC 110~220V )
NMEA GPS
PC (Not Supplied)
Satellite Receiver
(Not Supplied)
NMEA PC INTERFACE
Satellite Receiver
(Not Supplied)
ANT RF1 RECEIVER
TV
(Not Supplied)
DC 24V

7
The components of the Intellian i4 Inland are designed as module
system so that it is suitable for simple installation on all types of vessels.
System Components
Antenna Unit
The antenna of Intellian i4 Inland is comprised of the following
components for optimum search and receive capabilities for satellite
signal.
• Mechanical Unit – manipulates the antenna to receive the optimal
satellite signal regardless of the movement of the vessel.
• Control Unit – controls mechanical operation of the antenna.
• RF Unit – transmits the optimum satellite signal to the receiver.
• Radome – protects the antenna from the severe marine environment.
Installation
Figure 2 : Radome

8
Intellian Satellite TV Antenna Systems
Antenna Control Unit (ACU)
The Antenna Control Unit (ACU) provides the power to the antenna and
controls the various settings of the antenna. The digital VFD (Vacuum
Fluorescent Display) allows for easy operation of the ACU, even in the
dark.
The functions of the ACU are as follows:
• Controls the antenna system
• Provides power to the antenna unit
• Monitors the antenna status
• Changes the target satellite
• Set up the user environment
• Set the current GPS information
• Set satellite information
• Move antenna manually
• Perform self-diagnosis of the antenna
• Set up the interface with a PC
Figure 3 : Front & Rear of ACU
NMEA
ANT RF1 RECEIVER
DC 24V PC INTERFACE
FG - +
+ -
Front
Rear
Antenna Control Unit
Front
Rear

9
Installation Kit
Contains the items required for securing the antenna unit and ACU to the
vessel.
Other Components
No Components Size Qty
1 ACU Table Mounting Bracket - 2
2 RG6 (Antenna - ACU RF Cable) 15m 1
3 RG6 (ACU-Receiver Cable) 3m 1
4 Power Cable 1.5m 1
5 PC USB Cable 1.5m 1
6AC Adaptor 1.5m 1
7 NMEA Connector AK950-2 1
8
Hex Bolt M8x35L 5
Tapping Screw ø4x16L 5
ø3x8L 5
Flat Washer M8 5
Spring Washer M8 5
Installation CD - 1
9Mounting Template - 1
10 Installation Plate - 1
11 Quick Installation Guide - 1
Figure 5 : List of the Supplied Parts
Figure 4 : Installation Bolt Kit
Hex.Bolt
5
-
Flat Washer
5
-
Spring Washer
5
-
Antenna ACU
Item
Qty
Size
Self-Tapping Screw
5
(M4 X 16L)
Machine Screw
5
(M3 X 8L)

10
Intellian Satellite TV Antenna Systems
Tools Required for Installation
Power Drill 11 mm Spanner
Cross-Head
Screwdriver 13 mm Spanner
10 mm Drill Bit
Ø80 mm
Hole Saw
Pencil
5 mm
Allen/Hex key
Figure 6 : Required Tools for Installation
Power Drill 11 mm Spanner
Cross-Head
Screwdriver 13 mm Spanner
10 mm Drill Bit
Ø80 mm
Hole Saw
Pencil
5 mm
Allen/Hex key

11
Planning the Installation
Antenna Unit
Install the antenna in accordance with the following procedures to
insure maximum performance of the antenna. The antenna should be
installed in the place where is an all round clear view of the horizon.
Please be sure there are no obstacles within 15 degrees above the
antenna. Any obstacles can prevent the antenna from tracking the
satellite signal (Refer to the drawing on the right).
Do not install the antenna near by the radar especially on the same
plane as their energy levels may overload the antenna front-end circuits.
It is recommended to position the antenna at least 4 feet (1.2m) above
or below the level of the radar and minimum of 15 feet (6m) away from
the high power short wave radars.
The mounting platform should be rigid enough and not subjected to
excessive vibration. The movement of the antenna can be minimized
by installing at the center of the vessel. For optimal performance of the
antenna, it is not recommended to install at any corner of the vessel,
where the movement of the vessel is the greatest. Install the bottom
of the antenna parallel to the surface of the sea and fix tightly to the
structure of the vessel. When setting the antenna down, be careful not
to damage the RF connector. Striking the connectors on the bottom
directly will damage the connector.
Figure 7 : Elevation Limit of Obstacles
15°

12
Intellian Satellite TV Antenna Systems
Cables
Before installing the system cables, consider the following points.
• All cables need to be well clamped and protected from physical
damage and exposure to heat and humidity.
• Cables with severe bends are not allowed.
• Where a cable passes through an exposed bulkhead or deckhead,
a watertight grommet or swan neck tube should be used.
Power Requirements
You need to follow the power requirements to avoid damaging the
system.
• Intellian Inland comes with an AC Power Adapter designed to a boat’s
power supply rated from 110~220 V AC.
• If your Receiver(s) and television(s) require a 110V/240V AC power
supply, you will need to install a suitable DC to AC converter to operate
the units from your boat’s DC power supply.
Extending the cables
The cables that have been supplied with your Intellian system should be
of adequate length to complete the installation on most boats.
Power Adapter
The supplied power adapter supports a power supply rated from
110~220V AC.
RF Cable
This cable is supplied at a length of 15m. If a longer length is required
you should replace this cable with an extended RF cable supplied by
Intellian Technologies.
Note: Exceeding the indicated cable lengths will result in reduced
performance of your system.

13
Figure 8 : Radome Dimension of i4 Inland
Ø43 cm (16.9”)
44 cm (17.3”)
Ø50 cm (19.7”)
54 cm (21.2”)
Installation and Mounting of Antenna
The method of installation and mounting of antenna may vary due
to vessel design but the following procedures are applicable in most
situations, and will result in a secure and effective installation.
Conrmation of Size Prior to Installation
• Confirm the height and diameter of the bottom surface of the antenna
before installing it.
• The space must be sufficient for installing the antenna unit
considering the height and diameter of the antenna.
• The height and the diameter of the bottom surface of the antenna are
as shown in the following drawing. If possible, install the antenna
using a power tower.
Note: Before installing the antenna, open the radome and remove
the shipping constraints from the antenna interior. Reinstall the radome
before operating the system. The system will not perform properly if
the radome is open.

14
Intellian Satellite TV Antenna Systems
Figure 9 : Mounting Hole Position of i4 Inland
RF1 RF2
RF3 RF4
22.86 cm (9”)
22.86 cm (9”)
23.3cm ( 9.2”)
14.15cm (5.6”)
Mark of the Antenna Mounting Position
Referring to the mounting template, mark where the antenna is to be
mounted on board the ship (it must be a flat surface) or on a separate
power tower by the drawing on the right.
Note: If a power tower is not used to mount the antenna, separate
cable shocks and waterproofing measures must be taken to protect
the RF connector from being exposed to sea water and external
shocks. An exposed cable may cause electric shock and cause serious
damage to the equipment.

15
Securing Holes for Bolts and Cable Ways
Make 4 bolt holes of 10mm diameter, one at each corner of a rectangle
drawn as below, and make a circular hole of 80mm diameter at the
center of the rectangle through which the cable will run.
Connection of the Cable
Remove the rubber cap from RF connector. Connect the RF cable to the
RF connector under the base plate through the access hole using an
11mm spanner. Be careful not to over tighten, as you may damage the
connector.
Figure 11 : Connectors on Bottom of Antenna
Note: Do not tighten excessively when using the spanner, this will
damage the threads. Be careful that the connectors do not touch the
mounting surface of the antenna, this might cause a critical malfunction
and serious damage to the equipment.
Ø80mm
Hole Saw
Ø 10mm
Drill
Figure 10 : Drilling Instruction
Antenna Unit
RF Cables
(Optional)
11mm
Spanner

16
Intellian Satellite TV Antenna Systems
Mounting the Antenna
Attach the antenna by using the hex head bolts (M8X35L), M8 spring
washers, and M8 flat washers supplied.
Figure 12 : Mounting the Antenna
Radome Base
Deck
M8 Flat Washer
M8 Spring Washer
M8 Hex. Bolt
13mm Spanner
ACU Dimensions
Installing the ACU
5.4 cm (2.1”)
5.5 cm (2.2”)
22.8 cm (9”)
17.8 cm (7”)
21.7 cm (8.5”)
18.5 cm (7.3”)
Figure 13 : Dimension of ACU

17
Figure 14 : Installation of ACU
Selecting ACU Installation Site
The ACU should be installed below deck, in a location that is:
• Dry, cool, and ventilated.
• Easy access from your main TV viewing area.
To Install the ACU
1. The ACU should be installed using the two supplied mounting
brackets which allow for a top or bottom mounting configuration.
2. Using the self tapping screws supplied, attach the mounting brackets
to the sides of the ACU.
3. Place the ACU in the location where it is going to be installed.
4. Connect the cables to the rear of the ACU.
5. Use a pencil to mark the 4 hole positions (two on each side), and
use the appropriate drill bit to drill.

18
Intellian Satellite TV Antenna Systems
Single Receiver Connection
1. Connect the RF cable 15m from the RF 1 connector on the
antenna base plate to the ANT. RF1 connector on the ACU.
2. Connect the RF cable 3m from the RECEIVER connector on the
ACU to RF connector on the Receiver.
3. Connect the DC power cable 1.5m from DC power connector on
the ACU to a power source from 110~220V AC.
4. Press the POWER ON switch on the ACU to start the operation of the
antenna system.
Figure 15 : Single Receiver Conguration
RF1 RF2
ANT RF1
FG - +
Antenna
ACU
Receiver
Adapter
( AC 110~220V )
RECEIVER
+ -
NMEA GPS
NMEA PC INTERFACE
USB Cable
IRD 1
RF3 RF4
DC 24V
Connecting the System Cables
After installation and fixation of the antenna, connect the ACU to the antenna.
Refer to the drawing below to connect cables.
Antenna RF Cable (Connecting Antenna - ACU)
Intellian provides the Antenna RF Cable (RG-6, 15 m) for connecting
Antenna and ACU. Due to the signal losses across the length of the RF
coax on L-Band, Intellian recommends the following 75 Ω coax cable
types for standard system installations. Check the instructions from the
cable supplier. The table below shows the recommended cable types
and maximum cable lengths for the antenna system. For installing
cables longer than the recommended length, consult with Intellian
Technologies first.
RF Cable Recommendation
Coaxial Cable Type Max. Cable Length
RG-6/U Solid Copper Core or
LMR 300 35 m
RG-11/U Solid Copper Core or
LMR 400 60 m
LMR 600 100 m

19
Twin Receivers Connection
You can connect two Receivers for your antenna as shown in the following
diagram. However, only one of the Receivers can be configured as a two
satellite receiver.
The other Receiver needs to be configured as a one satellite receiver.
The two satellite receiver determines which satellite is tracked, while the
other receiver can watch any channel which is available from the tracked
satellite.
As in the single Receiver option the RF cables from the antenna base plate
should be connected to ‘LNB’, ‘ANT’, or ‘Satellite In’ on the rear panel of
Receiver.
Figure 16 : Twin-Receivers Conguration
IRD1 (Not Supplied)
FG - +
Antenna
ACU
Receiver
Adapter
( AC 110~220V )
+ -
NMEA GPS
NMEA PC INTERFACE
USB Cable
RF3 RF4
RF1 RF2
DC 24V ANT RF1 RECEIVER
IRD2 (Not Supplied)

20
Intellian Satellite TV Antenna Systems
Multi-Receivers Connection
In order to connect multiple Receivers to the antenna, you will need to
purchase a suitable LNB multiswitch. The multiswitch has to be installed
between the antenna unit and the Receivers as shown in the following
diagram.
Figure 17 : Multi-Receivers Conguration
RF3 RF4
RF1 RF2
ANT RF1
FG - +
Antenna
ACU
Receiver
Adapter
( AC 110~220V )
RECEIVER
+ -
NMEA GPS
NMEA PC INTERFACE
USB Cable
IRD 4
Multi switch
(Not Supplied)
IRD 3
* IRD 1~4 : Not supplied
IRD 2IRD 1
DC 24V