Intellian i9 User manual

Intellian i9/i9P Serial Number
This serial number will be required for
all troubleshooting or service calls
made regarding this product.
Notice
All Right Reserved
Intellian i9/i9P® and Intellian® are the registered trademarks of Intellian
Technologies, Inc., and should not be appropriated without permission by
Intellian Technologies, Inc., and the information contained in this manual is the
property of Intellian Technologies, Inc. Any and all parts of this manual shall not
be reproduced and distributed in any form without written prior consent by
Intellian Technologies, Inc. The information contained in this manual shall be
subject to change at any time without notice due to the functional upgrade of the
product.
Copyright© Intellian Technologies, Inc.
Doc. No. I9/I9P-DC V100

CONTENTS
INTRODUCTION............................................................................................ 1
INTRODUCTION TO INTELLIAN I9/I9P................................................................... 1
FEATURES OF INTELLIAN I9/I9P........................................................................... 2
BASIC SYSTEM CONFIGURATION......................................................................... 3
INSTALLATION.............................................................................................. 4
SYSTEM COMPONENTS........................................................................................ 4
TOOLS REQUIRED FOR INSTALLATION ................................................................. 7
PLANNING THE INSTALLATION............................................................................. 8
INSTALLATION AND FIXATION OF ANTENNA ....................................................... 10
INSTALLING THE ACU....................................................................................... 14
CONNECTING THE SYSTEM TO A GPS................................................................. 17
TARGET SATELLITE SETTING............................................................................. 18
ADJUSTING THE LNB SKEW ANGLE (LINEAR POLARIZATION ONLY) ................. 19
OPERATION INSTRUCTION..................................................................... 21
INTRODUCTION ................................................................................................. 21
OPERATION USING THE ACU.................................................................. 22
ACU SOFT KEYS............................................................................................... 22
NORMAL MODE................................................................................................. 22
INITIAL SETUP................................................................................................... 23
SET UP MODE ................................................................................................... 27
OPERATION USING PC CONTROLLER PROGRAM........................... 49
INTRODUCTION ................................................................................................. 49
PROGRAM INITIALING AND SERIAL PORT SETUP ............................................... 50
MAIN MENU –USING DEFAULT DUAL-SAT MODE............................................. 51
SET SATELLITE INFORMATION........................................................................... 52
MAIN MENU-USING ADVANCED TRIPLE-SAT MODE......................................... 54
SET SATELLITE INFORMATION........................................................................... 55
CONTROLLER MENU.......................................................................................... 58
TROUBLESHOOTING................................................................................. 63
PREPARATION FOR TRANSPORTATION.............................................. 65
WARRANTY .................................................................................................. 66
APPENDIX : TECHNICAL SPECIFICATION.......................................... 67

Introduction 1
INTRODUCTION
Introduction to Intellian i9/i9P
Intellian i9/i9P (Intellian i9 or Intellian i9 Premium)
Intellian i9/i9P is a digital satellite antenna system designed specifically for
all types of vessels (Anchored or transit) to automatically identify, track
and capture satellite signals from the Digital Video Broadcasting (DVB:
the international standard for digital TV transmissions) compatible
Satellites.
Specifically, Intellian i9/i9P has Wide Range Search (WRS) algorithm,
which minimizes the search time at initial state and Dynamic Beam Tilting
(DBT) technology, which dynamically shapes the antenna beam to utilize
stabilization. Once the satellite is acquired, the antenna DBT continuously
measures the heading, pitch, and roll of the vessel by obtaining satellite
signal level around the antenna point, and transmits commands to the
antenna motors to keep the antenna pointed at the satellite at all times.
This active stabilization is enhanced by a conical scan tracking function to
detect and lock onto the strongest signal, resulting in the clearest
reception possible.
GPS is built into the Intellian i9/i9P. The Intellian i9P also has a built-in
function of automatic adjustment of skew angle of LNB. With the two
added built-in features the Intellian i9/i9P enables for faster and more
efficient tracking of satellites. With the premium series it is not required to
put additional GPS information and to change skew angles when traveling
away from the original optimized GPS data and skew angle.

2 i9/i9P Satellite Antenna System – Install and User Manual
Features of Intellian i9/i9P
Enjoy satellite broadcasts at sea
Intellian i9/i9P is the most modern antenna system that enables you to
receive high quality broadcasting signal at sea where the atmospheric and
environmental condition is very harsh.
Fully Automatic Control System
Fully automatic control system allows for you to simply turn the power
switch on having crystal clear high quality satellite television in motion or
at anchor.
High Quality Antenna
The high tech antenna technology has been adopted for this parabolic
antenna system which is optimal for the marine conditions and it enables
you to receive the optimal level of signal even when it rains or snows.
Fast and efficient search for the satellite
The WRS (Wide Range Search) algorithm allows for the antenna system
to search the satellite within the shortest amount of time and to detect the
satellite signal under any position and any directional movement of the
ship.
Easy to install and outstanding durability
Guaranteed reliability through the implementation of a modularized design
and the usage of strictly proven components.
Built-in GPS
Intellian i9/i9P has imbedded GPS, which allows for the system to upload
the GPS data automatically into the system for an even faster and stable
system.
Automatic Skew Angle Adjustment
The automatic skew model allows for the Intellian i9P to automatically
change the skew position to the optimal skew angle at all times to
ensure maximum level of satellite signal level.

Introduction 3
Basic System Configuration
In order to work your satellite TV system properly, the system will have to
connect with all of the provided components properly as shown in the
figure below (Refer to next chapter ‘Installation’ of this manual for the
more detail connection method). Separate purchase of a satellite receiver
and a TV is required.
NMEA GPS
PC( No t Supplied)
DC Po wer o n Vessel
(DC-10.8-15.6V)
An ten n a
Con trol Un it
TV(NotSupplied)
Satellite Receiver (Not Supplied)
View A
IRD (Not Supplied)
View A (Optional RF Cable)
IRD (Not Supplied)
IRD (Not Supplied)

4 i9/i9P Satellite Antenna System – Install and User Manual
Installation
The components of the Intellian i9/i9P have been designed to be modular so
that it may be suitable for simple installation on all types of vessels.
System Components
Antenna Unit
The antenna of Intellian i9/i9P is composed with the following components for
the optimum search and reception of the satellite signal.
yMechanical Part – manipulates the antenna to receive the optimal
satellite signal regardless of the movement of the vessel. 3 axes
(azimuth, elevation and skew)
yControl part – controls mechanical operation of the antenna
yRF part – transmits the optimum satellite signal to the receiver.
yRadome – protects the antenna from the severe marine
environment.

Installation 5
Antenna Control Unit (ACU)
Antenna Control Unit (ACU) provides the power to the antenna and controls
the various settings of the antenna. Additionally, VFD (Vacuum Fluorescent
Display) allows for you to access the ACU in the dark.
The functions of the Intellian i9/i9P ACU are as follows.
yProvide power for the Antenna Unit
yMonitor the antenna status
ySet up the user environment
ySet the current GPS information
ySet satellite information
yMove antenna manually
yPerform self-diagnosis of the antenna
ySet up the interface with PC
Front
Rear

6 i9/i9P Satellite Antenna System – Install and User Manual
Anten n a ACU
Hex. Bolt
5EA
Hex Head
Wrench Bolt
5EA
Flat Washer
5EA
Spring
Washer
5EA
Hex. Nut
5EA
Tapping
Screw
(Φ4x16L)
5EA
Machine
Screw
(Φ3x8L)
5EA
Installation Kit
Contain the items required for securing the antenna unit and ACU to your
boat.
Other Components
No Components Size Q’ty
1 ACU Bracket - 2EA
2 RG6(Antenna – ACU RF Cable) 30m 1EA
3 RG6(ACU – IRD Cable) 3m 1EA
4 Power Cable 10m 1EA
5 PC Serial Cable 1.8m 1EA
6 Power & SLC Cable 30m 1EA
7 NMEA Connector AK950-2 1EA
8 Power Connector AK950-3 1EA
9
Hex Bolt M8x60L 5EA
Hex Head Wrench Bolt M6x35L 5EA
Tapping Screw
ø4×16L 5EA
ø3×8L 5EA
Flat Washer M8 10EA
M6 5EA
Spring Washer M8 5EA
Nut M8 5EA
Eye Nut M6 5EA
10 Install CD - 1EA
11 Manual - 1EA
12 Installation Template 420x330 1EA

Installation 7
Tools Required for Installation
Power Bit
Cross-Head
Screwdriver
11mm Spanner
13mm Spanner
Φ10mm(3/8”)
Bit Pencil

8 i9/i9P Satellite Antenna System – Install and User Manual
Planning the installation
Selection of Installation Site
Install the antenna in accordance with the following procedure to secure the
maximum functionality of the antenna.
The ideal antenna site has a
clear view of the horizon/
satellite all around. Please be
sure to see if there are any
obstacles 15 degrees above
elevation blocking the antenna.
Any obstacles located above 15
degree elevation can prevent
the antenna from tracking satellite signal (Refer to the drawing).
Keep the antenna out of line with nearby radars, as their energy levels may
overload the antenna front-end circuits. If necessary, position the Antenna
Unit so it is at least four feet (1.2 meters) above or below the level of the
radar.
Make sure that the mounting surface is rigid so that it cannot flex when the
vessel vibrates. If necessary, add a strength member to the mounting site to
stiffen it.
The movement of the antenna can be minimized by installing it at the center
of the ship. For optimal performance of the antenna it is not recommended to
install at any corners of the ship, where the movement of the ship is the
greatest.
Install the bottom of the antenna parallel to the surface of the sea and fix
tightly to the structure of the ship.
When the antenna is to be laid down, be careful not to have the power
connector and/or RF connector damaged by striking directly against the
bottom, which causes connection to be impossible.
AntennaUnit
15°
Obstacle

Installation 9
Cables
Before installing the system cables, you need to take the following points
into consideration.
yAll cables need to be well clamped and protected from physical
damage and exposure to heat and humility.
yCable with an acute bends is not allowed.
yWhere a cable passes through an exposed bulkhead or deckhead,
a watertight gland or swan neck tube should be used.
Power requirements
You need to follow the power requirements to avoid damage the system.
Intellian i9/i9P has been designed to work on a boat’s power supply rated
from 10.8~15.6 V DC.
If your IRD(s) and television(s) require a 110V/240V AC power supply, you
will need to install a suitable DC to AC converter to operate the unit(s) from
your boat’s DC power supply.
Extending the cables
The cables that have been supplied with your Intellian system should be of
adequate length to complete the installation on most boats.
Power Cable
This cable supplied at a length of 10m.
RF Cable
This cable is supplied at a length of 30m. If a longer length is required you
should replace this cable with the extended RF cable supplied by Intellian
Technologies.
The indicated cable lengths should not be exceeded as resulting in reduced
performance of your system.
WARNINGWARNING

10 i9/i9P Satellite Antenna System – Install and User Manual
Installation and fixation of antenna
The method of installation and fixation of antenna may be diverse with vessel
design but the following procedures are applicable in most situations and will
result in a secure and effective installation.
Confirmation of size and installation of power tower
yConfirm the height and diameter of the bottom surface of the
antenna before installing it.
yThe space must be sufficient for installing the antenna unit
considering the height and diameter of the antenna.
yThe height and the diameter of the bottom surface of the antenna
are as shown in the following drawing. If possible, install power
tower where antenna is to be installed.
Ø108 (42.5”)
110 (43.3”)
Unit : cm (inch)
Before installing the antenna you have to dismantle the radome with a
hexagon wrench tool and remove the foam fixation from the antenna
interior. You have to reassemble the radome before installation.
WARNINGWARNING

Installation 11
Mark of the antenna parking position
Referring to the size in the drawing, mark where antenna is to be parked on
board the ship (it must be a flat surface) or on a separate power tower by
drawing a regular exact square of each 12” in width and height.
30.37 (12”)
Forward
Backward
Unit : cm (inch)
30.37 (12”)
In case that power tower is not to be used, a separate cable shock and water
proofing measures shall be taken to protect the RF and the power cable from
being exposed to the sea water and external shocks. The exposed RF and
power cable may cause the electric shock and/or cause serious damage of
the equipments.
Securing hole for bolts and cable way
ø10mm(3/8”) Bit
Make 4 bolt holes of 10mm (3/8 in) diameter, one at each corner of an exact
square drawn as above.

12 i9/i9P Satellite Antenna System – Install and User Manual
Connection of Power & SLC Cable
Bring the Power & SLC cable up through the access hole and connect it to
the base-plate. Figure below illustrates the connector assignments.
Connection of RF cable
Remove the rubber protector for RF cable connector RF1 at the bottom of the
antenna. Connect the RF Cable to the RF1 connector under the base plate
through the access hole using the 13mm spanner. Be careful not to tighten
too much, as you may damage the connector.
RF Cable
Optional
11mm Spann er
Power Cable
Antennaunit
Do not use excessive force when using the spanner to avoid damage of the
screw part. Be careful so that the connectors do not directly touch to the
mounting surface of the antenna, or it may cause a critical malfunction and/or
a serious damage to the equipment.
WARNINGWARNING

Installation 13
Fixation of the antenna
Fix the antenna to the holes made before as the drawing below by using the
hex head bolts (M8x50L), M8 spring washer, M8 flat washer and M8 nut
supplied.
Antenna Unit
M8 Flat Washer
13mm Spanner
13mm Spanner
M8 Hex. Bolt
M8 Flat Washer
M8 Spring Washer
M8 Nut

14 i9/i9P Satellite Antenna System – Install and User Manual
Installing the ACU
ACU dimensions
5.38 (2.1”)
21.68(8.5”)
20.8 (8.2”)
22.8 (9”)
17.8 (7”)
5.5(2.2”)
13(5.1”)
18.5(7.3”)
Unit : cm (inch)
Selection of Installation Site
The ACU should be installed below decks, in a place of :
yDry, cool, and ventilated.
yEasy accessible from your main TV viewing area.
.

Installation 15
To Install the ACU
1. The ACU should be installed using the two fixing brackets supplied to
provide a top or bottom fix.
2. Using the self tapping screws supplied fix the mounting brackets to the
sides of the ACU.
3. Place the ACU in the position where it is going to be installed.
4. Connect the cables to the rear of the ACU.
5. Using a pencil to mark the 4 hole positions (2 each side) for securing the
mounting brackets and using a suitable drill bit to drill them.

16 i9/i9P Satellite Antenna System – Install and User Manual
Connection of ACU and antenna
After installation and fixation of the antenna, connect the ACU to the antenna.
Referring to the drawing below, connect cables.
NMEA GPSDC Power Cable PC Cable
IRD2 (Not Supplied)
TV(NotSupplied)
IRD1(NotSupplied)
IRD3 (Not Supplied)
IRD4 (Not Supplied)
RF Cable
Power Cable
(Optional)
(Optional)
(Optional)
yConnect the Power & SLC Cable (30m) from the antenna to the
ANTENNA connector on the rear of the ACU.
yConnect the RF Cable (30m) from the RF connector on the antenna to
the rear of IRD.
yConnect the power cable (10m) from DC power connector on the rear of
ACU to a power source of DC (10.8~15.6V).
yPress the POWER ON switch in front of the ACU to start the operation of
the Antenna system automatically.

Installation 17
Connecting the system to a GPS
For improved satellite tracking, you can connect your satellite TV system
directly to your boat’s NMEA 0183 GPS system. To do this you will need two
cables which are suitable for connecting to your GPS system and the green
2-way ACU GPS connector supplied with your Intellian i9/i9P Satellite TV
System.
To connect the system to a GPS
1. Strip back the insulation of each cable and connect a cable to each
terminal of the 2-way connector.
2. Tighten the locking screws.
3. Connect the cable from the +ve terminal of the ACU GPS connector
to the NMEA OUT wire of the boat’s GPS system.
4. Connect the cable from the –ve terminal of the ACU GPS connector
to the ground wire of the boat’s GPS system.
5. Refit the ACU GPS connector to the rear of the ACU.
Ground (-)NMEA out (+)

18 i9/i9P Satellite Antenna System – Install and User Manual
Target Satellite Setting
You can select the target satellite to receive satellite signal. If the target
satellite is not on the list you have to register the target satellite.
GPS Setting
You can input the GPS information through the ACU or the PC Program. To
setting the GPS information, the antenna system has to be in ‘SET UP mode’.
For detailed instructions, please refer to page 37; ‘Setting the GPS’, and page
58; ‘Set Antenna GPS and find Antenna Angle’.
Satellite registration
You can register the target satellite through the ACU or the PC Program. To
register the target satellite, the antenna system has to be in ‘ SET UP mode’
and the required information are, Satellite name, Satellite Longitude, Method
of Satellite identification, Frequency of each of the Band, Symbol Rate,
Network ID, Power Change method. For detailed instructions, please refer to
page 30; ‘Edit Satellite Information’, page 52;‘ Set Satellite Information’, and
page 59; ‘Set Tracking Information of Satellite’.
Satellite Pair Selection
You can select the Satellite pair from the list through the ACU or the program.
You can easily select the target satellite from the satellite pair. For detailed
instructions please refer to page 28; ‘Setting the Satellite pair’, page 52; ‘Set
Satellite Information’.
Target Satellite Selection
Choose the target satellite from the Satellite Pair. When selecting through
the ACU, you have to press the left button to select the target satellite while
the antenna system is in either ‘Searching Mode’ or ‘Tracking Mode’. When
using the PC program you can select either satellite ‘A’ or satellite ‘B’ from
‘Tracking Satellite’ at anytime.