Intellian i3 User manual

i3/i3L/i4/i4P
Installation and operation
User Manual
Document Number: 2012EF-UM1004-V1_0

2
Intellian Satellite TV Antenna Systems
Intellian i3/i3L/i4/i4P Serial Number
This serial number will be requested for all troubleshooting or service Inquiries.
Notice
All Right Reserved
Intellian i3/i3L/i4/i4P®and Intellian®are the registered trademarks of Intellian Technologies, Inc., and should not be appropriated without permission by Intellian Technologies,
Inc., and the information contained in this manual is the property of Intellian Technologies, Inc. Any and all parts of this manual shall not be reproduced and distributed in any form
without written prior consent by Intellian Technologies, Inc. The information contained in this manual shall be subject to change at any time without notice due to the functional
upgrade of the product.

3
INTRODUCTION
INTRODUCTION TO INTELLIAN i3/i3L/i4/i4P
FEATURES OF INTELLIAN i3/i3L/i4/i4P
BASIC SYSTEM CONFIGURATION OF INTELLIAN i3/i3L/i4/i4P
INSTALLATION
SYSTEM COMPONENTS
TOOLS REQUIRED FOR INSTALLATION
PLANNING THE INSTALLATION
INSTALLATION AND MOUNTING OF ANTENNA
INSTALLING THE ACU
ACU DIMENSIONS
SELECTING ACU INSTALLATION SITE
CONNECTING THE SYSTEM CABLES
CONNECTING THE SYSTEM TO A GPS
ADJUSTING THE LNB SKEW ANGLE (LINEAR POLARIZATION ONLY)
OPERATION INSTRUCTION
INTRODUCTION
OPERATING THE ACU
ACU SOFT KEYS
NORMAL MODE
SETUP MODE
OPERATION USING PC CONTROLLER PROGRAM
INTRODUCTION
PROGRAM INITIALING AND SERIAL PORT SETUP
MAIN MENU
CONTROLLER MENUS
PREPARATION FOR TRANSPORTATION
WARRANTY
APPENDIX : TECHNICAL SPECIFICATION
INTELLIAN i3/i3L
INTELLIAN i4/i4P
4
4
5
6
7
7
10
11
13
18
18
19
20
23
24
26
26
27
27
27
30
50
50
51
52
54
62
63
64
64
65
Table of Contents

4
Intellian Satellite TV Antenna Systems
Introduction to Intellian i3/i3L/i4/i4P
Intellian i3/i3L/i4/i4P is a digital satellite antenna system designed specically
for all types of vessels (anchored or transit) to automatically identify, track
and capture satellite signals from the Digital Video Broadcasting (DVB: the
international standard for digital TV transmissions) compatible satellites.
In details, Intellian i3/i3L/i4/i4P has Wide Range Search (WRS) algorithm, which
minimizes the search time during initialization, and Dynamic Beam Tilting (DBT)
technology, which dynamically shapes the antenna beam to utilize stabilization.
While tracking the target satellite, DBT technology uses a high-performance,
constantly adjusting sub-reector which allows the antenna to remain relatively
still, eliminating the constant whine of stepper motors while staying locked on to
the satellites.
The i3/i3L/i4/i4P has a builtin GPS system which enhances the speed of satellite
signals acquisitions. In addition, the i4P provides the embedded auto skew angle
control system to maintain the optimal signal strength and increase the quality of
satellite receptions in weak satellite single coverage area.
Introduction

5
Introduction
Features of Intellian i3/i3L/i4/i4P
Enjoy satellite broadcasts at sea
Intellian i3/i3L/i4/i4P is the most modern antenna system that enables
you to receive a high quality broadcasting signal at sea, where the
atmospheric and environmental condition are very harsh. This fully
automatic control system allows you to simply turn the power switch
on, and have crystal clear, high quality satellite television in motion or at
anchor.
High quality antenna
High tech parabolic antenna technology has been adopted for this
antenna system, which is optimal for marine conditions. This enables
you to receive the optimal signal level even when it is raining or
snowing.
Fast and efcient search for the satellite
The WRS (Wide Range Search) algorithm allows for the antenna
system to search the satellite within the shortest amount of time and
to detect the satellite signal under any position and with any directional
movement of the vessel.
Easy installation and outstanding reliability
Intellian i3/i3L/i4/i4P uses only one RF cable for installation. This makes
installation easy. Power, RF and data signals transfer from the antenna
to the ACU through this single cable. In addition, Intellian i3/i3L/i4/
i4P provides highly reliable system through the implementation of a
modularized design, and the usage of strictly proven components.
Built-in GPS
The built-in GPS system enhances the speed of acquisition of the
satellite signal and provides Intellian i3/i3L/i4/i4P even higher
performance.
Built-in automatic skew angle control system (i4P Only)
The automatic skew control system allows Intellian i4P to maintain the
optimal skew angle at all times and ensure maximum level of satellite
signal level receptions.
Intellian’s environmental test standards certied
These standards are much severer than a typical experienced marine
equipment condition. All testes performed with one unit through all
continued sequences. Intellian standards meet LR and DNV standards as
well as EN60945.

6
Intellian Satellite TV Antenna Systems
Basic System Conguration of Intellian
For your satellite TV system to function properly, the system will have to
be connected with all of the provided components as shown on the right
(Refer to the next chapter ‘Installation’ in this manual for more detailed
connection instructions). Separate purchase of a satellite receiver and a
TV is required.
Note: i3L can only be connected to one receiver.
Note 2: Dish and Bell TV users please refer to the Intellian Dish MIM
Installation and User Manual.
Figure 01 : Basic Conguration with 2 Receivers
ANT RF1
FUSE
FG - +
+ -
TV
(Not Supplied)
Antenna Control Unit
DC Power on Vessel
( 9~30 V DC )
NMEA GPS
PC( Not Supplied)
Satellite Receiver #2
(Not Supplied)
RF1
RF2
NMEA
RECEIVER
DC 9~30V PC INTERFACE
TV
(Not Supplied)
Satellite Receiver #1
(Not Supplied)

7
The components of the Intellian i3/i3L/i4/i4P are designed as module
system so that it is suitable for simple installation on all types of
vessels.
System Components
Antenna Unit
The antenna of Intellian i3/i3L/i4/i4P is comprised of the following
components for optimum search and receiving satellite signal.
• Mechanical Unit – manipulates the antenna to receive the optimal
satellite signal regardless of the movement of the vessel.
• Control Unit – controls mechanical operation of the antenna.
• RF Unit – transmits the optimum satellite signal to the receiver.
• Radome – protects the antenna from the severe marine environment.
Installation
Figure 02 : Radome

8
Intellian Satellite TV Antenna Systems
Antenna Control Unit (ACU)
The Antenna Control Unit (ACU) provides the power to the antenna and
controls the various settings of the antenna. The digital VFD (Vacuum
Fluorescent Display) allows for easy operation of the ACU, even in the
dark.
The functions of the ACU are as follows:
• Controls the antenna system
• Provides power to the antenna unit
• Monitors the antenna status
• Changes the target satellite
• Set up the user environment
• Set the current GPS information
• Set satellite information
• Move antenna manually
• Perform self-diagnosis of the antenna
• Set up the interface with a PC
Figure 03 : Front & Rear of ACU
NMEA
ANT RF1 RECEIVER
FUSEDC 9~30V PC INTERFACE
FG - +
+ -
Front
Rear
Antenna Control Unit

9
Installation Kit
Contains the items required for securing the antenna unit and ACU to the
vessel.
Other Components
No Components Size Qty
1 ACU Table Mounting Bracket - 2EA
2 RF Cable (ACU to IRD) 49ft (15m) 1EA
3 RF Cable (ACU to IRD) 10ft (3m) 1EA
4 DC Power Cable 33ft (10m) 1EA
5 PC Serial Cable 6ft (1.8m) 1EA
6 NMEA Connector AK950-2 1EA
7 Power Connector AK950-3 1EA
8 Hex Bolt M8x35L 5EA
9 Tapping Screw ø4x16L 5EA
ø3x8L 5EA
10 Flat Washer M8 5EA
11 Spring Washer M8 5EA
12 Installation CD - 1EA
13 User Manual - 1EA
14 Mounting Template i3/i3L 1EA
i4/ i4P
15 Quick Installation Guide - 1EA
Figure 05 : List of the Supplied Parts
Figure 04 : Installation Bolt Kit
Hex.Bolt
5
Hex. Nut
5
Spring Washer
5
Flat Washer
5
Antenna
Item
Qty
ACU
Item
Qty
Size
Self-Tapping Screw
5
(M4 X 16L)
Machine Screw
5
(M3 X 8L)

10
Intellian Satellite TV Antenna Systems
Tools Required for Installation
Power Drill 11 mm Spanner
Cross-Head
Screwdriver 13 mm Spanner
10 mm Drill Bit
Ø80 mm
Hole Saw
Pencil
5 mm
Allen/Hex key
Power Drill 11 mm Spanner
Cross-Head
Screwdriver 13 mm Spanner
10 mm Drill Bit
Ø80 mm
Hole Saw
Pencil
5 mm
Allen/Hex key
Figure 06 : Required Tools for Installation

11
Planning the Installation
Antenna Unit
Install the antenna in accordance with the following procedures to
ensure maximum performance of the antenna. The antenna should
be installed in a place where it has an all-around clear view of the
horizon. Please be sure there are no obstacles within 15 degrees above
the antenna. Any obstacles can prevent the antenna from tracking the
satellite signal (Refer to the drawing on the right).
Do not install the antenna near by the radar especially on the same
plane as their energy levels may overload the antenna front-end circuits.
It is recommended to position the antenna at least 4 feet (1.2m) above
or below the level of the radar and minimum of 15 feet (6m) away from
the high power short wave radars.
The mounting platform should be rigid enough and not subjected to
excessive vibration. The movement of the antenna can be minimized
by installing at the center of the vessel. For optimal performance of the
antenna, it is not recommended to install at any corner of the vessel,
where the movement of the vessel is the greatest. Install the bottom
of the antenna parallel to the surface of the sea and x tightly to the
structure of the vessel. When setting the antenna down, be careful not
to damage the RF connector. Striking the connectors on the bottom
directly will damage the connector.
Figure 07 : Elevation Limit of Obstacles
15°

12
Intellian Satellite TV Antenna Systems
Cables
Before installing the system cables, consider the following points.
• All cables need to be well clamped and protected from physical
damage
and exposure to heat and humidity.
• Cables with severe bends are not allowed.
• Where a cable passes through an exposed bulkhead or deckhead,
a watertight grommet or swan neck tube should be used.
Power Requirements
Follow the power requirements to avoid damage to the system.
The Intellian i3/i3L/i4/i4P has been designed to work on a boat’s power
supply rated from 9 ~ 30 V DC.
If your IRD(s) and television(s) require a 110V/240V AC power supply,
you will need to install a suitable DC to AC converter to operate the
unit(s) from your boat’s DC power supply.
RF Cable
This cable is supplied at a length of 49ft (15m). If a longer length is
required you should replace this cable with an extended RF cable
supplied by Intellian Technologies.
Extending the Cables
The cables that have been supplied with your Intellian system should be
of adequate length to complete the installation on most vessels.
Note: Exceeding the indicated cable lengths will result in reduced
performance of your system.

13
Installation and Mounting of Antenna
The method of installation and mounting of antenna may vary due
to vessel design but the following procedures are applicable in most
situations, and will result in a secure and effective installation.
Conrmation of Size Prior to Installation
• Check the height and diameter of the bottom surface of the antenna
before installing.
• The space must be sufcient for installing the antenna unit
considering the height and diameter of the antenna.
• The height and the diameter of the bottom surface of the antenna are
as shown
in the following drawing. If possible, install the antenna using a power
tower.
Note: Before installing the antenna, open the radome and remove the
shipping constraints from the antenna interior. Reinstall the radome
before operating the system. The system will not perform properly if the
radome is open.
Figure 08 : Radome Dimension of i4 / i4P
Ø43 cm (16.9”)
44 cm (17.3”)
Ø50 cm (19.7”)
54 cm (21.2”)

14
Intellian Satellite TV Antenna Systems
Figure 09 : Radome Dimension of i3 / i3L
Ø43 cm (16.9”)
44 cm (17.3”)
Ø50 cm (19.7”)
54 cm (21.2”)

15
Mark of the Antenna Mounting Position
Referring to the mounting template, mark where antenna will be
mounted on board (it must be a at surface) or on a separate power
tower.
Note: If a power tower is not suitable to mount the antenna, separate
cable shock and waterproong measures must be taken to protect the
RF connector from being exposed to the sea water and external shocks.
An exposed cable may cause electric shock and cause serious damage
to the equipment.

16
Intellian Satellite TV Antenna Systems
Figure 11 : Mounting Hole Position of i3 / i3LFigure 10 : Mounting Hole Position of i4 / i4P
22.86 cm (9”)
22.86 cm (9”)
23.3cm ( 9.2”)
14.15cm (5.6”)

17
Securing Holes for Bolts and Cable Ways
Make 4 bolt holes of 10mm diameter, one at each corner of a rectangle
drawn as below, and make a circular hole of 80mm diameter at the
center of the rectangle through which the cable will run.
Connection of the Cable
Remove the rubber cap from RF connector. Connect the RF cable to the
RF connector under the base plate through the access hole using an
11mm spanner. Be careful not to over tighten, as you may damage the
connector.
Figure 13 : Connectors on Bottom of Antenna
Note: Do not tighten excessively when using the spanner, this will
damage the threads. Be careful that the connectors do not touch the
mounting surface of the antenna, this might cause a critical malfunction
and serious damage to the equipment.
Ø80mm
Hole Saw
Ø 10mm
Drill
Figure 12 : Drilling Instruction
Antenna Unit
RF1 Cable
Optional
11mm
Spanner

18
Intellian Satellite TV Antenna Systems
Mounting the Antenna
Attach the antenna by using the hex head bolts (M8X35L), M8 spring
washers, and M8 at washers supplied.
Figure 14 : Mounting the Antenna
Radome Base
Deck
M8 Flat Washer
M8 Spring Washer
M8 Hex. Bolt
13mm Spanner
ACU Dimensions
Installing the ACU
5.4 cm (2.1”)
5.5 cm (2.2”)
22.8 cm (9”)
17.8 cm (7”)
21.7 cm (8.5”)
18.5 cm (7.3”)
Figure 15 : Dimension of ACU

19
Figure 16 : Installation of ACU
Selecting ACU Installation Site
The ACU should be installed below deck, in a location that is:
• Dry, cool, and ventilated.
• Easy access from your main TV viewing area.
To Install the ACU
1. The ACU should be installed using the two supplied mounting
brackets which allow for a top or bottom mounting conguration.
2. Using the self tapping screws supplied, attach the mounting brackets
to the sides of the ACU.
3. Place the ACU in the location where it is going to be installed.
4. Connect the cables to the rear of the ACU.
5. Use a pencil to mark the 4 hole positions (two on each side), and
use the appropriate drill bit to drill.

20
Intellian Satellite TV Antenna Systems
After installing and mounting the antenna, connect the ACU to the
antenna. Refer the drawing on the right to connect the cables.
Single IRD Connection
1. Connect the RF cable 49ft (15m) from the RF 1 connector on the
antenna base plate to the ANT. RF1 connector on the ACU.
2. Connect the RF cable 10ft (3m) from the RECEIVER connector on the
ACU to RF connector on the IRD.
3. Connect the DC power cable 33ft (10m) from DC power connector on
the ACU to a power source from 9~30 V DC.
4. Press the POWER ON switch on the ACU to start the operation of the
antenna system.
Figure 17 : Single IRD Conguration
NMEA
ANT RF1 RECEIVER
FUSEDC 9~30V PC INTERFACE
FG - +
+ -
RF1 RF2
RF Cable
DC
Power
Cable NMEA
GPS
PC
Cable
ACU
IRD (Not Supplied)
Connecting the System Cables of i3/i3L/i4/i4P