Intellinet 522755 User manual

802.11g Super-G 108Mb Wireless Access Point
Quick Installation Guide

The enclosed Hardware Installation Guide gives you a step-by-step explanation of
how to install your 108Mb Super-G PCI Adapter. Further technical assistance and all
updated drivers can be accessed at
www.intellinet-network.com
Here you have access to 24hour support and can contact our support team to
answer any questions you may have.
In order to provide the requested support we need the following details from you:
•A clear description of the problem;
•Version number of the drivers you are using (always check the website to see
whether you are using the latest version);
•Type of PC you are using;
•Operating system you are using
For more information about Intellinet products, please visit the Intellinet Web Site:
www.intellinet-network.com
ATTENTION!
The Software installation as described below, may be slightly different from the
installation on your computer. This depends on the Windows version you are using.

BEFORE YOU GET STARTED…
Getting started
•Before you can configure the Intellinet 802.11g Super-G Wireless Access Point, you should
have an Ethernet connection with your computer. Be sure that you have an Ethernet card
installed and that it is working properly. For a detailed description how to setup a network, see
our manual at the CD-ROM
•Use a network Ethernet switch or cross over UTP cable to connect the Intellinet 802.11g
Super-G Wireless Access Point to the computer.
•Use a fixed IP address to be sure that you can connect to the Intellinet 802.11g Super-G
WirelessAccess Point. Default IP address of the Intellinet 802.11g Super-G Wireless Access
Point: 10.0.0.1
•You have to configure your computer in the same IP range as the Intellinet 802.11g Super-G
WirelessAccess Point. You can use a Fixed IP address in the 10.0.0.x range. Use as ‘Subnet
Mask’255.0.0.0
•The Intellinet 802.11g Super-G Wireless Access Point is protected with a login. Default login:
Username: admin
Password: <empty>, (no password, by default)*
* You can set a password later in the configuration of the Intellinet 802.11g Super-G Wireless Access
Point.
Basic Configuration Intellinet 802.11g Super-G Wireless Access Point
Open the web browser
Type in the IPAddress of the Access Point
Note: if you have changed the default IP Address assigned to the 802.11g Wireless Access
Point, make sure to enter the correct IP Address.
Type admin in the User Name field
Leave the Password blank
Click OK

Once entered, the Current Status screen will appear.
There are three other options available in this screen: Setup Wizard, Advanced Setup, and
Statistics.
Current Status
The left-hand side of the Current Status screen provides basic information about your wireless access
point, including the MAC Address, IP Address, Subnet Mask and Default Gateway.
On the right-hand side, you’ll find the SSID (Service Set Identifier), the Channel number, Rate, and
Security Level. Please note this information, since you’ll need it when you use the Setup Wizard.
All these settings, with the exception of the MAC Address, may be changed or modified using the
Advanced Setup screen.
(If the Security Level on your WAP is enabled, all devices on the network must also be at the same level
of security, using the identical security system and encryption codes. For initial setup, it is
recommended that security be disabled.)

Setup Wizard
Using the built-in Setup Wizard is the easiest and quickest way to connect to a wireless network. To
take advantage of this convenient technology, simply click Setup Wizard at the top of the Current
Status screen. The following screen will appear.
Click Next to continue.
Enter the SSID (Service Set Identifier) as displayed on the Current Status screen. You may ether accept
the default Channel number, or enter a new Channel number.
Cick Next.

This screen displays the present level of security on your Access Point. To use encryption, click
Enabled, choose the Key Size, and enter the encryption Key Value.
Click Next.
(If the Security Level on your WAP is enabled, all devices on the network must also be at the
same level of security, using the identical security system and encryption codes. For initial
setup, it is recommended that security be disabled.)
Just that easily, your setup is completed. Click Reboot to save your current settings and restart your
802.11g Wireless Access Point.
After rebooting, the sign-in window will reappear. Simply type in admin (or a new user name and
password if you have changed them).
For more advanced settings of the Intellinet 802.11g Super-G Wireless Access Point, please use our
online manual at the CD-ROM.
By default the Intellinet 802.11g Super-G Wireless Access Point will forward all DHCP requests of
your network.
A wireless client can be running within a few minutes in combination with the Intellinet 802.11g
Super-G Wireless Access Point.