IntelliSense IS-2260 Service manual

Wire Knockouts
Wall Mount
Knockouts
Corner Mount
Pilot Holes
Wall Mount
Corner Mount
Position 0
Used with 76 (2.3 m)
Wide Angle Lens
Curt in Lens *
Position 1
Used with 10 (3 m)
Wide Angle Lens *
IS-2260 / IS-2260T Passive Infrared Motion Sensor
Mounting Guidelines
 Select a mounting location in which
the likely direction of intruder motion
is across the coverage pattern rather
then towards or away from the sensor.
 o not install where the sensor is
exposed to direct sunlight, or is close
to strong sources of heat.
 Make sure there are no obstructions
that can block the pattern of coverage.
 o not install in an area where rapid
temperature changes from central
heating, radiators, ducts, air conditioning,
open flames, etc. are likely.
 Avoid running sensor cables close
to other cables especially for extended
distances or where the other cables
radiate excessive electromagnetic
interference.
Open the unit. Select wire and wall mount knockouts
to be used and carefully break them
out.
Pull wire out of the
wall and remove 3
(8 cm) of cable
jacket. Insert wires
into back housing
and attach with
wire tie. Cut excess
wire tie.
Push out on the latch on the right side of
the housing and gently pull up on the PCB
to remove.
Do not use for wires.
Mount the sensor in the desired location.
Set alignment post according to mounting
height and lens used.
Connect the wires to terminal as shown
using 18-22 AWG (0.3-1.0 mm2) wire.
Observe the proper polarity.
IS-2260
IS-2260T
12 V C Power
To closed circuit
protective loop
12 V C Power
To closed circuit
protective loop
To Tamper Loop
12
34 5To enable the LE , remove the LE enable/disable
jumper link. To disable the LE , replace the jumper
link.
6Set Pulse Processing Option
Intermediate Pluse Processing (INT): This is the recommended setting for any location
where an intruder is expected to cross only a small portion of the coverage area. It
tolerates normal environments.
Note: NOT recommended for pet immune applications.
Note: Recommended if using the optional curtain lens.
Standard Pulse Processing (STD): This is the recommended setting for most applica-
tions. It tolerates environmental extremes.
Note: This is the recommended setting for pet immune applications.
Harsh Pulse Processing (HARSH):This is the recommended setting for the severest of
environments and should only be used in locations where an intruder is expected to
cross moderate to large portions of the coverage area.
* Curtain lens and 10 wide angle lens are not
intended for use in pet applications.
Installation Instructions
LE Enable LE isable
Intermediate Standard Harsh
Terminal
LE
LE
Enable/
isable
Jumper
Pulse Processing
Jumper
Alignment
Post
Printed Circuit oard

IS-2260 / IS-2260T Passive Infrared Motion Sensor
Range:
Wide Angle Lens: 60 x 120 (18 m x 36 m)
Curtain Lens: 100 x 20 (30.5 m x 6 m)
PIR Detector Fields-of-View edges):
44 long range
12 intermediate
6 lower
Pulse Processing:
Intermediate, Standard, Harsh selectable
Temperature Compensation:
Advanced dual-slope temperature compensation
adjusts for ambients both above and below body
temperature.
Detectable Walk Rate:
0.5 - 10 ft./Second
Indicator:
Red LE with enable/disable link
Alarm Relay:
Form A, SPST, 90 mA @ 16 V C
15 Ohm protective resistor
Input Voltage:
8 - 14 V C
Current:
W/LE 10 mA
W/O LE 4 mA
Standby 4 mA
Standby:
Power source should be capable of at least four hours
of battery standby.
Tamper: IS-2260T only)
NC (with cover on), 0.5 A, 30 V C
Operating Temperature:
14° to 122° F (-10° to 50° C)
Operation Humidity:
Up to 95% RH (max.), non-condensing
Dimensions:
4-3/8 x 2-1/4 x 1-1/2 (11.2 cm x 6 cm x 4 cm)
Accessories:
Lens Option Kit 18 - 10 (3 m) Wide Angle
Lens Option Kit 19 - Curtain Lens
SMB-10 Swivel Mount Bracket
Note: The Lens Options and Swivel Mount Bracket
should not be used in pet applications.
Specifications
The IS-2260/2260T passive infrared motion sensor is a versatile wall-mounted unit
employing Fresnel lenses and offering efficient coverage patterns for commercial
and residential applications.
When installed per the guidelines, the Uniform Sensitivity Optics technology in the
IS-2260 provides reasonable false alarm protection against pets and other animal
up to 40 lbs.
To activate look-down capabilities, remove the lens/bug guard assembly.
Use a screwdriver to push in and out on the look-down tab until it breaks off.
(Not to be removed for pet applications.)
Special Instructions
for Installations Containing Pets
To take full advantage of the pet immunity the guidelines below should be
followed:
 Mount the center of the sensor 76 (2.3 m) high.
 Set the PIR sensitivity for Standard (ST ).
 Mount where animals cannot come within 6 (1.8 m) of the
sensor by climbing on furniture, boxes, or other objects.
 o not aim the sensor at stairways that can be climbed by animals.
Note: o not break out look-down tab for sensors using pet applications.
Note: This sensor will provide immunity to false alarms for an individual
animal or a group of animals whose total weight is equal to or less than 40
lbs. when the room temperature is above 50° F (10° C).
Note: Pet immunity for this sensor has not been evaluated by
Underwriters Laboratories, Inc.
Note: Only the 76 (2.3 m) mounting height lens provides immunity to
animals moving within the field-of-view.
Important: Two-minute warm-up time is required after applying power.
1. Remove the front cover and set Pulse Processing Option to the
setting appropriate for the installation. The LE must be enabled at
this time.
2. Replace the front cover and walk through detection zones,
observing that the sensors LE lights whenever motion is detected
(The LE serves as a walk-test indicator during this procedure).
The absolute range of all PIR units is subject to variation because of
different types of clothing, backgrounds, and ambient temperature. For
this reason, ensure that the most likely intruder routes are well within
the PIRs detection zones and that walk-testing is carried out along
those routes.
Detection Patterns
Top View
Wide Angle Lens
76 (2.3 m) or 10 (3 m)
Mounting Height
Side View
Wide Angle Lens
76 (2.3 m)
Mounting Height
Side View
Wide Angle Lens
10 (3 m) Mounting
Height
Top View
Curtain Lens
Side View
Curtain Lens
Note: Intermediate Pulse Processing setting should be
set when using the optional curtain lens.
Supplemental Information
IntelliSense is a registered trademark of Honeywell, Inc. Copyright © 2001 IntelliSense®
All rights reserved.
PN 5-051-654-00 Rev B
* Look-down fingers
are enabled when the
look-down tab is
removed.
lower intermediate
*down
long range
Test Procedure