Interlogix TVB-5302 Instruction sheet

TruVision Series 3 IP
Camera FW3.1
Configuration Manual
P/N 1073187-EN • REV D • ISS 29SEP17

Copyright
©
2017 United Technologies Corporation.
Interlogix is part of UTC
Climate, Controls & Security, a unit of
United Technologies Corporation.
All rights reserved.
Trademarks and
patents
T
rade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer
Interlogix
.
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA
Authorized EU manufacturing representative:
UT
C Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Contact information
For contact information
, see www.utcfireandsecurity.com or
www.firesecurityproducts.com
.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 1
Content
Introduction 3
Network access 5
Checking your web browser security level 5
Activating the camera 7
Overview of the camera web browser 9
Camera configuration 11
Configuration menu overview 11
Local configuration 12
System time 13
Network settings 15
Recording parameters 26
Video image 29
OSD (On Screen Display) 33
Overlay text 34
Privacy masks 35
Motion detection alarms 36
Tamper-proof alarms 40
Exception alarms 40
Alarm inputs and outputs 42
Cross line detection 44
Intrusion detection 46
Snapshot parameters 47
NAS settings 49
Storage devices 50
Recording schedule 50
Camera management 54
User management 54
RTSP authentication 56
IP address filter 57
Restore default settings 58
Import/export a configuration file 59
Upgrade firmware 59
Reboot camera 60
Camera operation 61
Logging on and off 61
Live view mode 62
Playing back recorded video 62
Searching event logs 65

2 TruVision Series 3 IP Camera FW3.1 Configuration Manual
Operating PTZ control 67
Index 70

TruVision Series 3 IP Camera FW3.1 Configuration Manual 3
Introduction
This is the user manual for TruVision Series 3 IP camera models:
IP fixed lens bullet camera:
TVB-5301 (2MPX Bullet, 4 mm lens)
TVB-5302 (4MPX Bullet, 4 mm lens)
IP VF lens bullet camera:
TVB-5303 (2MPX Bullet, 2.8 to 12 mm VF lens)
TVB-5304 (4MPX Bullet, 2.8 to 12 mm VF lens)
IP motorized lens bullet camera:
TVB-5305 (2MPX Bullet, 2.8-12 mm VF motorized lens)
TVB-5306 (4MPX Bullet, 2.8-12 mm VF motorized lens)
IP fixed lens dome camera:
TVD-5301 (2MPX Plastic Dome, 2.8 mm lens)
TVD-5302 (4MPX Plastic Dome, 2.8 mm lens)
IP VF lens dome camera:
TVD-5303 (2MPX VF Dome)
TVD-5304 (4MPX VF Dome)
IP motorized lens dome camera:
TVD-5305 (2MPX Dome, 2.8-12 mm VF Motorized lens)
TVD-5306 (4MPX Dome, 2.8-12 mm VF Motorized lens)
IP wedge camera:
TVW-5301 (2MPX Wedge, 2.0 mm lens, Gray)
TVW-5302 (2MPX Wedge, 2.8 mm lens, Gray)
TVW-5303 (2MPX Wedge, 2.8 mm lens, White)
TVW-5304 (2MPX Wedge, 2.8 mm lens, Black)
TVW-5305 (4MPX Wedge, 2.8 mm lens, Gray)
IP turret camera:
TVT-5301 (2MPX Turret, 2.8 mm lens, Gray)
TVT-5302 (2MPX Turret, 2.8 mm lens, White)
TVT-5303 (2MPX Turret, 2.8 mm lens, Black)
TVT-5304 (4MPX Turret, 2.8 mm lens, Gray)

4 TruVision Series 3 IP Camera FW3.1 Configuration Manual
TVT-5305 (4MPX Turret, 2.8 mm lens, White)
TVT-5306 (4MPX Turret, 2.8 mm lens, Black)
TVT-5307 (4MPX Turret, 4.0 mm lens, White)

TruVision Series 3 IP Camera FW3.1 Configuration Manual 5
Network access
This manual explains how to configure the camera over the network with a web
browser.
TruVision IP cameras can be configured and controlled using Microsoft Internet
Explorer (IE) and other browsers. The procedures described use Microsoft
Internet Explorer (IE) web browser.
Checking your web browser security level
When using the web browser interface, you can install ActiveX controls to
connect and view video using Internet Explorer. However, you cannot download
data, such as video and images due to the increased security measure.
Consequently you should check the security level of your PC so that you are able
to interact with the cameras over the web and, if necessary, modify the Active X
settings.
Configuring IE ActiveX controls
You should confirm the ActiveX settings of your web browser.
To change the web browser’s security level:
1. In Internet Explorer, click Internet Options on the Tools menu.
2. On the Security tab, click the zone to which you want to assign a web site
under “Select a web content zone to specify its security settings”.
3. Click Custom Level.
4. Change the ActiveX controls and plug-ins options that are signed or
marked as safe to Enable. Change the ActiveX controls and plug-ins
options that are unsigned to Prompt or Disable. Click OK.
- Or -

6 TruVision Series 3 IP Camera FW3.1 Configuration Manual
Under Reset Custom Settings, click the security level for the whole zone in
the Reset To box, and select Medium. Click Reset.
Then click OK to the Internet Options Security tab window.
5. Click Apply in the Internet Options Security tab window.
Windows users
Internet Explorer for Windows operating systems have increased security
measures to protect your PC from any malicious software being installed.
To have complete functionality of the web browser interface with Windows, do
the following:
• Run the Browser interface as an administrator in your workstation
• Add the camera’s IP address to your browser’s list of trusted sites
To add the camera’s IP address to Internet Explorer’s list of trusted sites:
1. Open Internet Explorer.
2. Click Tools, and then Internet Options.
3. Click the Security tab, and then select the Trusted sites icon.
4. Click the Sites button.
5. Clear the “Require server verification (https:) for all sites in this zone” box.
6. Enter the IP address in the “Add this website to the zone” field.
7. Click Add, and then click Close.
8. Click OK in the Internet Options dialog window.
9. Connect to the camera for full browser functionality.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 7
Activating the camera
When you first start up the camera, the Activation window appears. You must
define a high-security admin password before you can access the camera. There
is no default password provided.
You can activate a password via a web browser and via TruVision Device
Manager (included on the CD to find the IP address of the camera).
To activate the camera via the web browser:
1. Power on the camera and connect the camera to the network.
2. Input the IP address into the address bar of the web browser, and click Enter
to enter the activation interface.
Notes:
The default IP address of the camera is 192.168.1.70.
For the camera to enable DHCP by default, you must activate the camera
via TruVision Device Manager. Please refer to the following section, “To
activate the camera via TruVision Device Manager” below.
3. Enter the password in the password field.
Note: A valid password range must be between 8 and 16 characters. You can
use a combination of numbers, lower and upper case letters, and special
characters : _ - , . * & @ / $ ? Space. The password must contain characters
from at least two of these groups. We also recommend that you reset your
password regularly. For high security systems, it is particularly recommended
to reset the password monthly or weekly for better protection.
4. Confirm the password.
5. Click OK to save the password and enter the live view interface.
To activate the camera via TruVision Device Manager:
1. Run the TruVision Device Manager to search for online devices.
2. Check the device status from the device list, and select the inactive device.

8 TruVision Series 3 IP Camera FW3.1 Configuration Manual
3. Enter the password in the password field, and confirm it.
Note: A valid password range must be between 8 and 16 characters. You can
use a combination of numbers, lower and upper case letters, and special
characters : _ - , . * & @ / $ ? Space. The password must contain characters
from at least two of these groups. We also recommend that you reset your
password regularly. For high security systems, it is particularly recommended
to reset the password monthly or weekly for better protection.
4. Click OK to save the password.
A pop-up window confirms activation. If activation fails, confirm that the
password meets the requirement and try again.
5. Change the device IP address to the same subnet with your computer by
either modifying the IP address manually or checking the checkbox of Enable
DHCP.
6. Input the password and click the Save button to activate your IP address
modification.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 9
Overview of the camera web browser
The camera web browser lets you view, record, and play back recorded videos
as well as manage the camera from any PC with Internet access. The browser’s
easy-to-use controls give you quick access to all camera functions. See Figure 1
below.
If there is more than one camera connected over the network, open a separate
web browser window for each individual camera.
Figure 1: Web browser interface – Live view
Table 1: Overview of the web browser interface
Name Description
1. Live view Click to view live video.
2. Playback Click to play back video.
3. Log Click to search for event logs. There are three main types: Alarm,
Exception and Operation.
4. Configuration Click to display the configuration window for setting up the
camera.
5. PTZ controls Zoom and focus options are available for motorized lens
cameras.
6. Current user Displays current user logged on.
7. Logout Click to log out from the system. This can be done at any time.

10 TruVision Series 3 IP Camera FW3.1 Configuration Manual
Name
Description
8. Aspect ratio Select the aspect.
9. Streaming Switch between main stream and substream.
10. Viewer View live video. Time, date and camera name are displayed here.
11. Start/stop live view Click to start/stop live view.
12. Audio Adjust volume.
13. Manual Alarm Click to trigger the alarm output.
14. Bidirectional audio Turn on/off microphone.
15. Capture Click to take a snapshot of the video. The snapshot will be saved
to the default folder in JPEG format.
16. Start/stop recording Click to record live video.
17. Digital zoom Click to enable digital zoom.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 11
Camera configuration
This chapter explains how to configure the cameras through a web browser.
Once the camera hardware has been installed, configure the camera’s settings
through the web browser. You must have administrator rights in order to
configure the cameras over the internet.
The camera web browser lets you configure the camera remotely using your PC.
Web browser options may vary depending on camera model.
There are two main folders in the configuration panel:
Local configuration
Configuration
Configuration menu overview
Use the Configuration panel to configure the server, network, camera, alarms,
users, transactions and other parameters such as upgrading the firmware. See
Figure 2 and Table 2 below for descriptions of the configuration folders available.
Figure 2: Configuration panel (Device Information tab selected)
Table 2: Overview of the Configuration panel
Configuration folders Description
1. System Defines the camera name and number. Displays basic information on
the device including SN and the current firmware version
, time settings,
maintenance, and serial port parameters. See “System time” on page
13, “Restore default settings” on page 58, and “Upgrade firmware” on
page 59 for more information.

12 TruVision Series 3 IP Camera FW3.1 Configuration Manual
Configuration folders Description
2.
Network
Defines the network parameters required to access the camera over
the internet. See “Network settings” on page 15 for more information.
3.
Video/Audio
Defines recording parameters. See “Recording parameters” on page
26 for more information.
4.
Image
Defines the image parameters, OSD settings, overlay text, and privacy
mask. See “Video image” on page 29, “OSD (On Screen Display)” on
page 33, “Overlay text” on page 34, and “Privacy masks” on page 35
for more information.
5.
Security
Defines who can use the camera, their passwords and access
privileges, RTSP authentication, IP address filter, and SSH access.
See “Camera management” on page 54 for more information.
6.
Basic
Events Defines motion detection, tamper-proof, alarm input/output, and
exception. See “Motion detection alarms” on page 36, “Tamper-proof
alarms” on page 40, and “Exception alarms” on page 40.
7.
Smart Event
Defines cross line and intrusion detection.
8.
Storage
Defines recording schedule, storage management, NAS configuration,
and Snapshot parameters. See “NAS settings” on page 49, “Storage
devices” on page 50, and “Recording schedule” on page 50 for more
information, and “Snapshot parameters” on page 47 for more
information.
Local configuration
Use the Local menu to manage the protocol type, live view performance and
local storage paths. In the Configuration panel, click Local Configuration to
display the local configuration window. See Figure 3 and Table 3 below for
descriptions of the different menu parameters.
Figure 3: Example of a configuration window (Local configuration shown)

TruVision Series 3 IP Camera FW3.1 Configuration Manual 13
Table 3: Overview of the Local configuration window
Parameters Description
Live View Parameters
1.
Protocol
Specifies the network protocol used.
Options include: TCP, UDP, MULTICAST and HTTP.
2.
Live View Perfor
mance Specifies the transmission speed.
Options include: Shortest Delay or Auto.
3.
Rules
It refers to the rules on your local browser. Specify whether or
not to display the colored marks when motion detection, face
detection, and intrusion detection are triggered. For example,
when the rules option is enabled and a face is detected, the
face will be marked with a green rectangle in live view.
4.
Image Format
Choose the image format for a snapshot: JPEG or BMP.
Record File Settings
5.
Record F
ile Size Specifies the maximum file size.
Options include: 256 MB, 512 MB and 1G.
6.
Save
Record Files to Specifies the directory for recorded files.
7.
Save
Downloaded Files to Specifies the directory for downloaded files.
Snapshot and Clip Settings
8.
Save
Snapshots In Live View
To
Specifies the directory for saving snapshots in live view mode.
9.
Save
Snapshots When
Playback To
Specifies the directory for saving snapshots in playback mode.
10.
Save Clips To
Specifies the directory for saving video clips in playback mode.
System time
NTP (Network Time Protocol) is a protocol for synchronizing the clocks of
network devices, such as IP cameras and computers. Connecting network
devices to a dedicated NTP time server ensures that they are all synchronized.
To define the system time and date:
1. Click Configuration > System > Time Settings.

14 TruVision Series 3 IP Camera FW3.1 Configuration Manual
2. From the Time Zone drop-down menu select the time zone that is the closest
to the camera’s location.
3. Under Time Sync, check one of the options for setting the time and date:
Synchronize with an NTP server: Check the NTP enable box and enter the
server NTP address. The time interval can be set from 1 to 10080 minutes.
- Or -
Set manually: Enable the Manual Time Sync.function and then click to
set the system time from the pop-up calendar.
Note: You can also check the Sync with computer time check box to
synchronize the time of the camera with the time of your computer.
4. Check Enable DST to enable the DST function, and set the date of the DST
period.
5. Click Save to save changes.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 15
Network settings
Accessing the camera through a network requires that you define certain network
settings. Use the “Network” folder to define the network settings. See Figure 4
and Table 4 below for further information.
Figure 4: Network window (TCP/IP tab shown)
Table 4: Network parameters
Parameters Description
1.
TCP/IP
NIC Type: Specifies the NIC type. Default is Auto. Other options include:
10M Half-dup, 10M Full-dup, 100M Half-dup and 100M Full-dup.
DHCP: Enable to automatically obtain an IP address and other network
settings from that server.
IPv4 Address: Specifies the IPv4 address of the camera.
IPv4 Subnet Mask: Specifies the IPv4 subnet mask.
IPv4 Default Gateway: Specifies the IPv4 gateway IP address.
IPv6 Mode: Specifies the IPv6 mode, including Manual, DHCP and Router
Advertisement.
IPv6 Address: Specifies the IPv6 address of the camera.
IPv6 Subnet Prefix Length: Specifies the IPv6 prefix length.
IPv6 Default Gateway: Specifies the IPv6 gateway IP address.
Mac Address: Specifies the mac address of the camera.
MTU: Specifies the valid value range of MTU. Default is 1500.
Multicast Address: Specifies a D-class IP address between 224.0.0.0 to
239.255.255.255. Only specify this option if you are using the multicast
function. Some routers prohibit the use of multicast function in case of a

16 TruVision Series 3 IP Camera FW3.1 Configuration Manual
Parameters Description
network storm.
Enable Multicast Discovery: Enables the automatic detection of the online
network camera via private multicast protocol in the LAN.
DNS server: Specifies the preferred and alternate DNS server for your
network.
2.
Port
HTTP Port: The HTTP port is used for remote internet browser access.
Enter the port used for the Internet Explorer (IE) browser. Default value is
80.
RTSP Port: RTSP (Real Time Streaming Protocol) is a network control
protocol designed for use in entertainment and communications systems to
control streaming media servers. Enter the RTSP port value. The default port
number is 554.
HTTPS Port: HTTPS (Hyper Text Transfer Protocol Secure) allows video to
be securely viewed when using a browser. Enter the HTTPS port, value. The
default port number is 443.
Server Port: This is used for remote client software access. Enter the server
port value. The default port number is 8000.
Alarm Server IP: Specifies the IP address of the alarm host.
Alarm Server Port: Specifies the port of the alarm host.
3.
DDNS
DDNS is a service that maps Internet domain names to IP addresses. It is
designed to support dynamic IP addresses, such as those assigned by a
DHCP server.
Specifies DynDNS, and ezDDNS.
DynDNS (Dynamic DNS): Enter the user name and password registered to
the DynDNS web site. The domain name is that of the DynDNS web site.
ezDDNS: Enter the host name. It will automatically register it online.
4.
PPPoE
Retrieves a dynamic IP address.
5.
SNMP
SNMP is a protocol for managing devices on networks. Enable SNMP to get
camera status and parameter related information.
6.
802.1X
When the feature is enabled, the camera data is secured and user
authentication is needed when connecting the camera to the network. See
page 15 for setup information.
7.
QoS
QoS (Quality of Service) can help solve the network delay and network
congestion by configuring the priority of data sending.
Enable the option in order to solve network delay and network congestion by
configuring the priority of data sending.
8.
FTP
Enter the FTP address and folder to which snapshots of the camera can be
uploaded.
6.
UPnP
The UPnP (Universal Plug and Play) protocol allows devices to connect
seamlessly and to simplify the implementation of networks in the home and
corporate environments. With the function enabled, you do not need to
configure the port mapping for each port, and the camera is connected to the
Wide Area Network (WAN) via the router.
Enable and set the friendly name detected.
7.
Email
Specifies the email address to which messages are sent when an alarm
occurs.

TruVision Series 3 IP Camera FW3.1 Configuration Manual 17
Parameters Description
8.
NAT
The UPnP (Universal Plug and Play) protocol allows devices to connect
seamlessly and to simplify the implementation of networks in the home and
corporate environments. With the function enabled, you do not need to
configure the port mapping for each port, and the camera is connected to the
Wide Area Network (WAN) via the router.
Enable and set the friendly name detected.
9.
HTTPS
Specifies authentication of the web site and its associated web server, which
protects against Man-in-the-middle attacks.
To define the TCP/IP parameters:
1. Click Configuration > Network >TCP/IP.
2. Configure the NIC settings, including the NIC Type, IPv4 settings, IPv6
settings, MTU settings, and Multicast Address.
3. If the DHCP server is available, check DHCP.
4. If the DNS server settings are required for some applications (e.g., sending
email), you should configure the Preferred DNS Server or Alternate DNS
Server.
5. Click Save to save changes.
To define the port parameters:
1. Click Configuration > Network > Port.

18 TruVision Series 3 IP Camera FW3.1 Configuration Manual
2. Set the HTTP port, RTSP port, HTTPS port, and server port of the camera.
HTTP Port: The default port number is 80. It can be changed to any port
number that is not occupied.
RTSP Port: The default port number is 554. It can be changed to any port
number in the range from 1 to 65535.
HTTPS Port: The default port number is 443. It can be changed to any port
number that is not occupied.
Server Port: The default server port number is 8000. It can be changed to
any port number in the range from 2000 to 65535.
3. Enter the IP address and port if you want to upload the alarm information to
the remote alarm host. Also check the Notify Alarm Recipient option in the
normal Linkage of each event page.
4. Click Save to save changes.
To define the DDNS parameters:
1. Click Configuration > Network > DDNS.
2. Check Enable DDNS to enable this feature.
3. Select the DDNS Type. Select one of the follow options: