Interlogix TruVisioin 12 Series User manual

TruVision 12/32 Series
IP Camera Installation
Guide
P/N 1072880-EN • REV B • ISS 08JAN15

Copyright © 2015 United Technologies Corporation,
Interlogix is part of UTC Building & Industrial
Systems, a unit of United Technologies
Corporation. All rights reserved.
Trademarks and
patents
Trade names used in this document may be trademarks
or registered trademarks of the manufacturers or
vendors of the respective products.
Manufacturer Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923,
USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance Class A: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction
manual, may cause harmful interference to radio
communications. Operation of this equipment in a
residential area is likely to cause harmful interference in
which case the user will be required to correct the
interference at his own expense.
ACMA compliance Notice! This is a Class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take
adequate measures.
Canada This Class A digital apparatus complies with Canadian

ICES-003.
Cet appareil numérique de la classe A est conforme à
la norme NMB-0330 du Canada.
European Union
directives
12004/108/EC (EMC directive): Hereby, UTC Fire &
Security declares that this device is in compliance with
the essential requirements and other relevant
provisions of Directive 2004/108/EC.
2012/19/EU (WEEE directive): Products marked with
this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon
the purchase of equivalent new equipment, or dispose
of it at designated collection points. For more
information see: www.recyclethis.info.
Contact information For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.

Installation Guide 1
Content
Introduction 2
Product overview 2
Installation 3
Installation environment 3
Package contents 4
Cable requirements 12
Camera description 13
Setting up the camera 17
IR illuminators 18
Accessing the SD card 19
Mounting the bullet camera 19
Mounting the VF dome camera 20
Mounting the outdoor dome camera 25
Using the camera with an Interlogix NVR or Hybrid DVR or
another system 30
Using the camera with TruVision Navigator 30
Specifications 30
TruVision IP box cameras 30
TruVision IP VF mini dome 31
TruVision IP VF bullet cameras 32
TruVision IP VF outdoor dome cameras 32
Pin definitions 33

2 Installation Guide
Introduction
Product overview
This is the installation guide for TruVision 12/32 Series IP
camera models:
TVC-1201 (1.3MPX IP box camera, PAL)
TVC-3201 (1.3MPX IP box camera, NTSC)
TVC-1202 (3MPX IP box camera, PAL)
TVC-3202 (3MPX IP box camera, NTSC)
TVB-1201 (1.3MPX IP bullet camera, 2.8-12mm, PAL)
TVB-3201 (1.3MPX IP bullet camera, 2.8-12mm, NTSC)
TVB-1202 (3MPX IP bullet camera, 2.8-12mm, PAL)
TVB-3202 (3MPX IP bullet camera, 2.8-12mm, NTSC)
TVB-1203 (3MPX IP bullet camera, 8-32mm, PAL)
TVB-3203 (3MPX IP bullet camera, 8-32mm, NTSC)
TVD-1201 (1.3MPX IP VF mini dome, 2.8-12mm, PAL)
TVD-3201 (1.3MPX IP VF mini dome, 2.8-12mm,
NTSC)
TVD-1202 (3MPX IP VF mini dome, 2.8-12mm, PAL)
TVD-3202 (3MPX IP VF mini dome, 2.8-12mm, NTSC)
TVD-1203 (1.3MPX IP outdoor dome, 2.8-12mm, PAL)

Installation Guide 3
TVD-3203 (1.3MPX IP outdoor dome, 2.8-12mm,
NTSC)
TVD-1204 (3MPX IP outdoor dome, 2.8-12mm, PAL)
TVD-3204 (3MPX IP outdoor dome, 2.8-12mm, NTSC)
TVD-1205 (3MPX IP outdoor dome, 8-32mm, PAL)
TVD-3205 (3MPX IP outdoor dome, 8-32mm, NTSC)
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
• Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a proper
PoE switch or a 12 VDC UL listed Class 2 or CE certified
power supply to power the camera. Do not overload the
power cord or adapter.
• Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
• Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
The operating temperature of the camera without heater
is between -30 to +60°C (-22 to 140°F). Humidity is below
90%. For the outdoor cameras have built-in heaters, the
operating temperature range is -40°C to 60°C(-40°F
to140°F)
• Moisture: Do not expose the camera to rain or moisture,
or try to operate it in wet areas. Turn the power off

4 Installation Guide
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.
• Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.
• Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.

Installation Guide 5
IP box camera
Camera C-CS adaptor
CD with Configuration
manual and TruVision
Device Finder
Installation manual
WEEE and Battery
Disposal

6 Installation Guide
IP VF bullet camera
Camera Back box
Template Alarm connector
(2 pcs)
Screws M4.8 × 18, 4pcs
to attach the back box
Screws (4 pcs)
Ceiling Mounting
11
11
2
22
2
1:Screw Hole for
Bracket
2:S crew Hole for
Mounting Base