Interlogix IFS POE302-SP User manual

IFS POE302-SP Ethernet Splitter
User Manual
P/N 1076527 • REV A • ISS 08FEB12

Copyright © 2012 UTC Fire & Security Company. All rights
reserved.
Trademarks and
patents
Interlogix, IFS POE302-SP Ethernet Splitter, the
IFS Brand and logo are trademarks of
UTC Fire & Security.
Other trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective
products.
Manufacture
r
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA
92626-5923, USA
Version This document applies to IFS POE302-SP
Ethernet Splitter version 1.0.
Certification N4131
FCC compliance Class A: This equipment has been tested and
found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference when the
equipment is operated in a commercial
environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not
installed and used in accordance with the
instruction manual, may cause harmful
interference to radio communications. Operation
of this equipment in a residential area is likely to
cause harmful interference in which case the user
will be required to correct the interference at his
own expense.
ACMA
compliance
Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be
required to take adequate measures.
European Union
directives
2004/108/EC (EMC directive): Hereby, UTC Fire
& Security declares that this device is in
compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC

2002/96/EC (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent
new equipment, or dispose of it at designated
collection points. For more information see:
www.recyclethis.info.
Contact
information
www.utcfireandsecurity.com or
www.interlogix.com
Customer support www.interlogix.com/customer-support

IFS POE302-SP Ethernet Splitter User Manual i
Contents
Package Contents 1
Product Features 1
Interface 1
PoE 1
Hardware 2
Standard Compliance 2
Product Overview 3
LED Indicator 3
Hardware Installation 3
Before Installation 4
PoE Injector and Splitter Installation 4
Connecting with other 802.3at Devices 5
Specifications 7
Contacting Technical Support 8

IFS POE302-SP Ethernet Splitter User Manual 1
Package Contents
Thank you for purchasing the IFS POE302-SP Gigabit High
Power over Ethernet (IEEE 802.3at) Splitter.
Open the package containing the Ethernet Splitter and
carefully unpack it. The box should contain the following items:
●IFS POE302-SP x1
●User Manual x1
●6 inch (15cm) UTP Straight Network Cable x1
●DC Plug Cable x 2
If any of these items are missing or damaged, please contact
your distributor or IFS Sales Rep. If possible, retain original
carton and packaging material, and use them again to repack
the product in case there is a need to return it to us for repair.
Product Features
Interface
• 2-Port RJ-45 interfaces
• 1-Port PoE Power+ Data input
• 1-Port Data output
• 1 DC out plug connector
PoE
• Complies with IEEE 802.3at Power over Ethernet PD
• Splits the 56V DC power over RJ-45 Ethernet cable into
12V/24V DC output
• Up to 1 non-IEEE 802.3at devices powered

2 IFS POE302-SP Ethernet Splitter User Manual
• Auto-detect of PoE IEEE 802.3at equipment protects
devices from being damaged by incorrect installation
• Two adjustable output voltage options (12VDC/2A,
24VDC/1A) to fit various device power requirements
• Distance of up to 100 meters
Hardware
• Metal case
• 12V / 24V DIP switch
• PoE Power in LED indicator
Standard Compliance
• IEEE 802.3 10Base-T
• IEEE 802.3u 100Base-TX
• IEEE 802.3ab 1000Base-T
• IEEE 802.3at Power over Ethernet standard
• FCC Part 15 Class A, CE
Note: PSE (Power Sourcing Equipment) is a device (eg.
switch or injector) that provides PoE power. Maximum allowed
continuous output power for a PSE device per IEEE 802.3at is
30 watts.
PD (Powered Device) is an Ethernet device powered by PoE
supplied by the PSE such as IP cameras, access control
panels, VoIP phones and Wireless access points (WAP), etc.

IFS POE302-SP Ethernet Splitter User Manual 3
Product Overview
Figure 1 shows the front and side panels of the POE302-SP.
Figure 1: POE302-SP Front and Side Panels
LED Indicator
POE302-SP LED indicator
LED Color Function
PoE In Green Steady on indicates the unit is receiving 56VDC
PoE in-line power.
Hardware Installation
The POE302-SP operates at three different data rates -
10Mbps, 100Mbps and 1000Mbps. The unit adjusts
automatically to the incoming data rate.
The following section describes the hardware features of the
POE302-SP. Carefully read this section before connecting any
network device to this unit.

4 IFS POE302-SP Ethernet Splitter User Manual
Before Installation
The POE302-SP separates data and power and provides two
DC power output options via a DIP switch.The two power
options are shown below.
• 12VDC/2A
• 24VDC/1A
Figure 2: Voltage output
The default switch setting is 12V.
Note: Please check the power requirements of the device that
will be receiving its power from the POE302-SP. If the power
requirements (voltage and current) exceed the power output
that the POE302-SP can supply, a built-in current overload
circuit will shutdown the POE302-SP to protect it from
damage. Power will then not be supplied to the connected
device.
PoE Injector and Splitter Installation
The POE302-MS (PSE) and the POE302-SP (PD) can be
installed in pairs. However, use of third-party devices is
allowed only if the device complies with the IEEE 802.3at
Power over Ethernet standard.
1. Connect a standard network cable from "Ethernet+DC" port
of POE302-MS to "PoE In" port of POE302-SP. The POE
LED of POE302-SP / POE302-MS will be constantly on.

IFS POE302-SP Ethernet Splitter User Manual 5
Figure 3: Connection Schematic
WARNING: The POE302-SP only accepts IEEE 802.3at
equipment; other in-line power device may cause the POE302-
SP malfunction.
2. Connect the UTP cable in the package from "Ethernet” port
of POE302-SP to the RJ-45 port of remote device.
3. Adjust proper DC power output and connect DC plug from
"DC OUT" of POE302-SP to remote device.
Caution: Please ensure the output voltage is correct for
remote device. Otherwise, it will damage your remote device.
4. Power on the remote device and its LED indicator will
remains on.
Connecting with other 802.3at Devices
The POE302-SP also provide the alternative to make the non
IEEE 802.3at devices the possibility to connect with an IEEE
802.3at in-line power device like Power over Ethernet Injector
or Power over Ethernet Switch, the figure is as below.

6 IFS POE302-SP Ethernet Splitter User Manual
Figure 4: Voltage output
Note: With IEEE 802.3at Power over Ethernet; the POE302-
SP also can co-work with the IEEE 802.3at End-Span High
Power over Ethernet Switch that is feeding power over pin 1,
2, and 3, 6.

IFS POE302-SP Ethernet Splitter User Manual 7
Specifications
POE302-SP Specifications
Product POE302-SP
Hardware Specification
“Data” Out Port 1 x RJ-45 STP
“PoE (Power +
Data)” Input Port 1 x RJ-45 STP
Interface
DC Out Plug
Connector 1
LED Indicator System: PoE In x 1 (Green)
Network Cable 10Base-T: 2-Pair UTP Cat. 3, 4, 5, up to 100m (328ft)
100Base-TX: 2-Pair UTP Ca5, 5e, & 6 up to 100m
(328ft)
1000Base-T: 2-Pair UTP Cat. 5, 5e, 6 up to 100m
(328ft)
EIA/TIA- 568 100-ohm STP (100m)
Data Rate 10/100/1000Mbps (vary on Ethernet device attached)
DIP Switch 12V DC / 24V DC output voltage
Dimension (W x D x H) 3.75 X 2.75 X 1.0 in (95 X 70 X25 mm)
Weight .25 lbs (111g)
Number of device can be
powered
1
Operating Temperature 0 ~ 50 Degree C
Storage Temperature -10 ~ 70 Degree C
Humidity 5 ~ 90% (Non-condensing)
Power over Ethernet
PoE Standard IEEE 802.3at High Power over Ethernet / PD
Standards Conformance
Standards Compliance IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Fast Ethernet
IEEE 802.3ab 1000Base-T Gigabit Ethernet
IEEE 802.3at Power over Ethernet
Regulation Compliance FCC Part 15 Class A, CE

8 IFS POE302-SP Ethernet Splitter User Manual
Contacting Technical Support
Contact technical support if you encounter any difficulties
during this installation. Please make sure you have the
requested diagnostic or log files ready before you contact us
by phone or go to www.interlogix.com/customer-support.
Technical Support
Europe, Middle East and Africa
W Select Contact Us at www.utcfssecurityproducts.eu
North America
T +1 855.286.8889
E [email protected]
Australia
E [email protected]