Interlogix TVE-DEC10 User manual

TVE-DEC10 IP Video
Decoder User Manual
P/N 1072583B-EN • REV 1.0 • ISS 16OCT12

Copyright
©
2012 UTC Fire & Security Americas Corporation, Inc.
Interlogix is part of UTC Climate Controls & Security, a unit of United
Technologie
s Corporation. All rights reserved.
Trademarks and
patents
The
Interlogix name and logo are trademarks of United
Technologies.
Other trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products
.
Manufacturer
UTC Fire & Security Americas Corporation, Inc.
2955 Red Hill Avenue, Costa Mesa, CA 92626
-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
N4131
FCC compliance
Class B:
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against har
mful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
There is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to corre
ct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for
help.
European Union
directives
12004/108/EC (EMC directive):
Hereby, UTC Fire & Security
Americas Corporation, Inc
.,
declares that this device is in compliance
or wit
h the essential requirements and other relevant provisions of
Directive 2004/108/EC
2002/96/EC (WEEE directive):
Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this
product to your local supplier
upon the purchase of equivalent new equipment, or dispose of it at
designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive):
This product contains a battery that
cannot
be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For
proper recycling, return the battery to your supplier or to a
designated collection point. For more information see:
www.recyclethis.info.
Contact information
For contact information
, see www.utcfireandsecurity.com or
www.utcfssecurityproducts.eu
.

TVE-DEC10 IP Video Decoder User Manual i
Content
Introduction 1
Package contents 1
Key features 1
Product description 2
Connections 3
Network settings 5
TruVision Device Finder 5
Using a web browser 8
Before you start 8
Accessing the web browser 8
Decoder operation 10
Dynamic decoding 11
Sequence mode 11
Remote playback 12
Display settings 14
Enable/disable decoding channel 14
Image scaling 15
Picture overlay 15
Connection status 16
Check decoding channel status 17
Check display channel status 17
Transparent channel 18
Configuration 19
Device properties 19
Time settings 20
Basic network settings 21
Alarm input settings 22
Serial ports 23
Arming time 23
User account management 24
Device management 26
Specifications 27

ii TVE-DEC10 IP Video Decoder User Manual

TVE-DEC10 IP Video Decoder User Manual 1
Introduction
The TruVision TVE H.264 IP video decoder converts compressed IP video
streams to analog video output for display. Based on a powerful DSP and a
stable embedded system design, the TVE-DEC10 decoder provides a high
resolution decoding function for both live view and playback streams from
Interlogix IP cameras, digital video recorders and network video recorders
This user manual provides basic information on setting up and using the TVE-
DEC10 model.
The decoder browser is shipped with on-screen display (OSD) menus in English
only.
Package contents
The TruVision TVE H.264 IP video decoder is shipped with the following items:
• TVE-DEC10 decoder
• Power adaptor
• Power cable
• Quick start guide
• CD (includes the user manual and TruVision Device Finder)
Key features
The following key features are supported by TVE decoders:
• Supports compression H.264 and MPEG4 codec
• Supports PS, RTP and proprietary encapsulation formats
• Powerful decoding capability: 1-channel video stream at 1080P resolution, 2-
channel video stream at 720P resolution, or 4-channel video stream at 4CIF
resolution
• Multiple video display outputs: BNC, VGA, HDMI, and DVI
• Compatible with Interlogix TruVision IP cameras and TruVision NVRs. Please
check the Interlogix web site for the latest compatible device list.
• Supports PSIA communication
• Discoverable via the TruVision Discovery Tool

2 TVE-DEC10 IP Video Decoder User Manual
Product description
Figure 1: Front panel
LED indicator
Description
P
WR The power LED
LINK
Network connection LED
RX/TX
Data transmitting/receiving status LED
RESET
Reset to factory default settings
VGA
VGA decoding output
DVI
DVI decoding output
HDMI
HDMI decoding output
VIDEO OUT
BNC decoding output
Figure 2: Back panel
Item
Name Description
1
. MIC In Microphone input.
2
. Audio Out Connect to an audio output device. R is right channel, L is left
channel.
3.
RS-232 Connect to an RS-232 device, such as a computer.
4.
RS-485 Connect to RS-485 serial port.
5.
Alarm Out Connect up to two alarm relay outputs.
Alarm In Connect up to four alarm relay inputs.
6.
LAN Connect the 10M/100M/1000Mbps self-adaptive UTP Ethernet
port to a network.
7.
12 VDC Connect a 12 V power supply via a PSU.
8
. GND Connect to ground.

TVE-DEC10 IP Video Decoder User Manual 3
Connections
See Figure 2 on page 2 for information on connecting the power, camera, audio
and network cables.
Alarm connections
The TVE decoder supports the open/close relay input as the alarm input mode.
When the alarm input signal is not in open/close relay signal mode, please follow
the connections shown below:
Figure 3: Alarm input connections
Alarm input connections for Emerson alarm:
Alarm input connections for normal alarm:
1
. Emerson alarm
2
. V output
3
. 10 V regulator
4. 4N35 optocoupler
5. Relay output
6. Normal alarm
7. JQC-3FG 24 V relay
The TVE decoder supports the open/close relay input as the alarm output mode.
The alarm input can be selected to NO or NC. Different alarm output connection
methods are applied to the AC or DC load. See Figure 3.
100Ω
ALM(-)
IN(n)
G
ALM(+)




TVE

Relay input
V-output
Emerson alarm
10 V regulator

10 V regulator
14N34
optocoupler
JQC-3FG
24 V relay
ALM(-)
ALM(+)


IN(n)
G

TVE
Relay input
V-output
Alarm


4 TVE-DEC10 IP Video Decoder User Manual
Figure 4: Alarm output connections
Note: Please note the different connections of JJ1 shown above. For a DC load,
JJ1can be safely used both in NC and NO methods. It is recommended to use
12 V / 1 A. For an external AC input, JJ1 must be open. The motherboard has
two jumpers, each corresponding to one alarm output. Both jumpers are factory
set to be connected.

TVE-DEC10 IP Video Decoder User Manual 5
Network settings
This chapter explains how to use TruVision Device Finder to find and configure
the IP address and other parameters of the device.
Note: The default user name of TVE is admin and the password is 1234. The
default IP address is 192.168.1.70
TruVision Device Finder
The TruVision Device Finder tool can be found on the CD shipped with that
product.
This tool automatically identifies TruVision devices that support “auto-discovery”
anywhere on the network, even in different subnets. You can view and modify the
IP address of any discovered device.
To install the TruVision Device Finder:
1. Insert the CD in the computer’s CD/DVD drive.
2. Browse to the folder IP Discovery Tool and double-click the Setup file located
in the folder.
3. Click Next.
4. Select the folder where setup will install the files then click Next.
5. The program requires a utility called WinPcap to be installed on the computer.
If it is already installed, go to step 6.
If the program is not installed, the WinPcap window appears. Follow the on-
screen instructions.

6 TVE-DEC10 IP Video Decoder User Manual
6. The TruVision Device Finder Wizard appears. Click Finish to complete its
installation.
Using the TruVision Device Finder
The setup will install the necessary files and place the following shortcut on your
desktop.
Figure 5: TruVision Device Finder shortcut icon
To use the TruVision Device Finder:
1. Double-click the shortcut icon to open the tool.
The Start window appears.
2. Click Start to begin the discovery process.
The list of TruVision devices located on your network appears.
Note: The TruVision Device Finder can only detect devices that are on the
same LAN. The tool cannot detect devices placed on a VLAN.