Interlogix TruVision Line User manual

TruVision
HD-
TVI Series
4 PTZ Dome
Camera
Installation Guide
P/N 1073206-EN • REV D • ISS 31AUG17

Copyright © 2017 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls & Security, a
unit of United Technologies Corporation. All rights
reserved.
Trademarks and
patents
Trade names used in this document may be
trademarks or registered trademarks of the
manufacturers or vendors of the respective products.
Manufacturer Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923,
USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification
FCC compliance Class A: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated in
a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the
instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference
in which case the user will be required to correct the
interference at his own expense.
FCC conditions This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This Device must accept any interference received,
including interference that may cause undesired
operation.

ACMA compliance Notice! This is a Class A product. In a domestic
environment this product may cause radio
interference in which case the user may be required
to take adequate measures.
Canada This Class A digital apparatus complies with CAN
ICES-003 (A)/NMB-3 (A).
Cet appareil numérique de la classe A est conforme
à la norme CAN ICES-003 (A)/NMB-3 (A).
European Union
directives
This product and - if applicable - the supplied
accessories too are marked with "CE" and comply
therefore with the applicable harmonized European
standards listed under the EMC Directive
2014/30/EU, the RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as unsorted
municipal waste in the European Union. For proper
recycling, return this product to your local supplier
upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For
more information see: www.recyclethis.info.
2013/56/EU &2006/66/EC (battery directive
)
: This
product contains a battery that cannot be disposed
of as unsorted municipal waste in the European
Union. See the product documentation for specific
battery information. The battery is marked with this
symbol, which may include lettering to indicate
cadmium (Cd), lead (Pb), or mercury (Hg). For
proper recycling, return the battery to your supplier
or to a designated collection point. For more
information see: www.recyclethis.info.
Contact
information
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu.

Installation Guide 1
Content
Introduction 3
Product overview 3
HD-TVI 1080P PTZ Dome Cameras 3
HD-TVI 1080P IR PTZ Dome Cameras 3
Installation 4
Installation environment 4
Package contents 5
Pendant/Wall HD-TVI PTZ dome 5
Surface/Flush HD-TVI PTZ dome 7
Pendant/Wall IR HD-TVI PTZ dome 9
Cable requirements 11
DIP switch settings 11
HD-TVI PTZ dome 11
IR pendant/wall mount HD-TVI PTZ dome 16
Terminal resistor settings (non-IR cameras only) 32
Camera description 34
IR illuminators 37
Mounting the outdoor HD-TVI PTZ dome 37
Mount the bracket on the wall 37
Mount the camera on the bracket 38
Flush mount the camera 41
Surface mount the camera 44
Using the camera with a TruVision recorder or another
system 49

2 Installation Guide
Specifications 50
TruVision Pendant/Wall HD-TVI PTZ camera 50
TruVision Surface/Flush HD-TVI PTZ Dome 50
TruVision Pendant/Wall IR HD-TVI PTZ Dome 51

Installation Guide 3
Introduction
Product overview
This is the installation guide for TruVision HD-TVI Series 4
PTZ Dome Camera models:
HD-TVI 1080P PTZ Dome Cameras
TVP-2401 (30X, Pendant/Wall mount, PAL)
TVP-2402 (30X, Surface/Flush mount, PAL)
TVP-4401 (30X, Pendant/Wall mount, NTSC)
TVP-4402 (30X, Surface/Flush mount, NTSC)
HD-TVI 1080P IR PTZ Dome Cameras
TVP-2403 (30X, Pendant/Wall mount, PAL)
TVP-4403 (30X, Pendant/Wall mount, NTSC)

4 Installation Guide
Installation
This section provides information on how to install the
cameras.
Installation environment
When installing your product, consider these factors:
•Electrical: Install electrical wiring carefully. It should be
done by qualified service personnel. Always use a CE
certified power supply (24VAC) to power the camera. Do
not overload the power cord or adapter.
•Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.
•Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings.
Humidity is below 90%. For the outdoor cameras that
feature built-in heaters, the operating temperature range
is -30 to 65°C (-22 to149°F)
•Moisture: Do not expose the camera to rain or moisture
or try to operate it in wet areas. Turn the power off
immediately if the camera is wet and ask a qualified
service person for servicing. Moisture can damage the
camera and also create the danger of electric shock.
•Servicing: Do not attempt to service this camera
yourself. Any attempt to dismantle or remove the covers
from this product will invalidate the warranty and may
also result in serious injury. Refer all servicing to qualified
service personnel.
•Cleaning: Do not touch the sensor modules with fingers.
If cleaning is necessary, use a clean cloth with some
ethanol and wipe the camera gently. If the camera will not

Installation Guide 5
be used for an extended period of time, put on the lens
cap to protect the sensors from dirt.
Package contents
Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use
the unit; contact the supplier immediately. If the unit is
returned, it must be shipped back in its original packaging.
Pendant/Wall HD-TVI PTZ dome
•Camera
•Installation manual
•CD with Configuration
manual
•WEEE and Battery
Disposal sheets

6 Installation Guide
•Foam pad
(Place it at the top of the
housing where the
harness exits).
•Desiccant 1
(Two small bags. Used
as the spare desiccant
for the PTZ dome. To
use this desiccant,
place it inside the cup
base and tie it with the
zip tie below.)
•Desiccant 2
(One large bag. Used to
keep the two bags of
desiccant away from
moisture prior to use).
•Zip tie (X2)
(Used to tie the
desiccant 1 bags
inside the PTZ dome)
•Wrench (T20)
•Safety lanyard

Installation Guide 7
Surface/Flush HD-TVI PTZ dome
•Camera
•CD with Configuration
manual
•Installation manual
•WEEE and Battery
Disposal sheets
•Desiccant 1
(Two small bags. Used as
the spare desiccant for the
PTZ dome. To use this
desiccant, place it inside
the cup base and tie it with
the zip tie below.)
•Desiccant 2
(One large bag. Used
to keep the two bags
of desiccant away
from moisture prior to
use).

8 Installation Guide
•Zip tie (2 pcs)
(Used to tie the desiccant
1 bags inside the PTZ
dome)
•Metal mounting base
•housing ring •Trim ring
•Drill template (224 mm or
8.82 in.)
•Phillips screws (4
pcs)

Installation Guide 9
•Dry wall anchors (4 pcs)
•Fixation pin (4 pcs)
Pendant/Wall IR HD-TVI PTZ dome
•Camera
•CD with Configuration
manual

10 Installation Guide
•Installation manual
•WEEE and Battery
Disposal sheets
•Desiccant 1
(Two small bags. Used
as the spare desiccant
for the PTZ dome. To
use this desiccant, place
it inside the cup base
and tie it with the zip tie
below.)
•Desiccant 2
(One large bag. Used
to keep the two bags of
desiccant away from
moisture prior to use).
•Safety lanyard •Wrench (M4)
CAUTION: Use direct plug-in UL listed power supplies
marked Class 2/CE certified or LPS (limited power source) of
the required output rating as listed on the unit.

Installation Guide 11
CAUTION: Risk of explosion if the battery is replaced by an
incorrect type. Dispose of used batteries according to the
instructions.
Cable requirements
Choose the video cable according to the transmission
distance. The minimum requirements for the coaxial video
cable are:
75Ω impedance
100% copper core conducting wire
95% weaving copper shield
RS-485 communication cable
24 VAC power cable
DIP switch settings
HD-TVI PTZ dome
For pendant/wall PTZ dome cameras, access the DIP switch
by removing the rubber plugs on the two sides of the PTZ
housing and unscrewing the two screws inside. Then open the
bubble assembly, remove all three foam inserts and the plastic
protective lens cover.
For surface/flush PTZ dome cameras, access the DIP
switches by rotating the housing.
Use the DIP switch to set the address and baud rate for the
PTZ dome. Value ON=1 and OFF=0.
Use the SW1 switches from the first to the eighth positions to
set the address. Use the SW2 switches to set the baud rate.

12 Installation Guide
Note: The default dome address is 0. The default baud rate is
2400.
Figure 1: DIP switch location for pendant/wall mount PTZ
dome
DIP switch
Figure 2: DIP switch location for surface/flush mount PTZ
dome
DIP switch
Figure 3: Enlarged view of the DIP switch

Installation Guide 13

Address settings
Use the SW1 switches from 1 to 4 to set the PTZ dome
address. Refer to Table 1 on setting the PTZ dome address to
a specific number.
Table 1: Set the dome address between 0 and 15
Dome
address
Switch no.
1 2 3 4
0 OFF OFF OFF OFF
1 ON OFF OFF OFF
2 OFF ON OFF OFF
3 ON ON OFF OFF
4 OFF OFF ON OFF
5 ON OFF ON OFF
6 OFF ON ON OFF
7 ON ON ON OFF
8 OFF OFF OFF ON
9 ON OFF OFF ON
10 OFF ON OFF ON
11 ON ON OFF ON
12 OFF OFF ON ON
13 ON OFF ON ON
14 OFF ON ON ON

14 Installation Guide
Dome
address
Switch no.
1 2 3 4
15 ON ON ON ON

Protocol settings
Use SW1 switches 5, 6 and 7 to set the PTZ dome protocol.
Refer to Table 2 below:
Table 2: Set the dome protocol
Protocol
SW1 switch no.
5 6 7
UTC RS-485 OFF OFF OFF
PROTOCOL_PELCO_P ON OFF OFF
PROTOCOL_PELCO_D OFF ON OFF
PROTOCOL_DIGIPLEX ON ON OFF
PROTOCOL_RS422_ASCII OFF OFF ON
PROTOCOL_BOSCH_CODE OFF ON ON
PROTOCOL_AD_CODE ON ON ON

HD-TVI mode settings
Use SW1 switch number 8 to set the HD-TVI mode of the PTZ
dome. HD-TVI Mode 1.0 and HD-TVI Mode 2.0 are two
standards to transfer HD-TVI signals. HD-TVI Mode 1.0
supports a short transmission distance with a wide bandwidth
while HD-TVI Mode 2.0 supports a long transmission distance
with a narrow bandwidth. Refer to the Table 3 below:

Installation Guide 15
Table 3: Set the HD-TVI mode
HD-TVI mode
SW1 switch no.
8
TVI 2.0 OFF
TVI 1.0 ON

Baud rate settings
Use the SW2 switches 1 and 2 to set the baud rate of the PTZ
dome. The baud rate can be 2400 bps, 4800 bps, 9600 bps or
19200 bps. The baud rate will be set as 2400 bps by default if
it is out of this range. Refer to Table 4 below:
Table 4: Set the baud rate of the dome
Baud rate
SW2 switch no.
1 2
2400 OFF OFF
4800 ON OFF
9600 OFF ON
19200 ON ON

16 Installation Guide
IR pendant/wall mount HD-TVI PTZ dome
Use the two DIP switches SW1 and SW2 to set the PTZ dome
address, baud rate, protocol, etc. Value ON =1 and OFF =0.
The switch label is on the back of the SWITCH cover, as
shown below.
Each number of the switch represents a DIP value, ranging
from 1 to 8 from the lowest to highest.
Figure 4: Label of DIP switch for pendant/wall mount HD-
TVI IR PTZ dome
Figure 5: Enlarged view of the DIP switches
Note: The default dome address is 0. The default baud rate is
2400. The default value of the 120Ω terminator is OFF.

Address settings
Use the SW1 switches to set the address of the PTZ dome.
Refer to Table 5 below :