Interlogix TruVision TVD-2404 User manual

TruVisio
n High Definition TVI
Vandal Dome Installation
Guide
TVD
-2402/TVD-4402
TVD-2404/TVD-4404
P/N 1072937-EN • REV A • ISS 12MAR15

2 Installation Guide
Content
Product overview 3
Camera description 5
Installation 7
Programming 12
Menu 15
Specifications 17
Legal and Regulatory information 18

Installation Guide 3
Product overview
This is the Pocket Guide for TruVision High
Definition TVI dome TVD-2402/TVD-4402 and TVD-
2404/TVD-4404. This guide describes a standard
installation.
Package contents:
Camera with power
and video output
cables
4 screws and 4
anchors for wall or
ceiling installation
Template
3 screws for install
the camera to back
box

4 Installation Guide
Hex wrench Monitor output
cable
Spare rubber
knockout
There is a rubber knockout
on the camera back box.
This one is for future use.
Installation Guide
CD
•WEEE and Battery
Disposal

Installation Guide 5
Camera description
1. Dome liner
2. Bubble
3. Lens
4. Power cable
5. CVBS video output
cable (black)
6. TVI video output
cable (grey)
7. Back box
8. DIP switch
9. Menu button
5
4
6
8
1
3
2
9
7

6 Installation Guide
Note:
Please check the camera output settings
before setting up a system. The TVI video
output can be only connected to DVR with
TVI signal input. The CVBS output supports
the standard monitor, test monitor, encoder
and DVR.
For TVD-2402/TVD-4202, the CVBS and TVI
output can not be performed at the same time,
you can use the built-in DIP switch to select
the camera video output.
For TVD-2404/TVD-4404, the built-in DIP
switch is used to enable/disable WDR feature,
when WDR feature is enabled, the CVBS
output will be blocked out.

Installation Guide 7
DIP switch
Installation
To install the camera on a ceiling:
1. Using the template, place it level against the
mounting surface and mark the position of the
mounting holes.

8 Installation Guide
2. Following all local codes, drill and prepare the
mounting holes.
3. Remove the camera from its back box.
4. Loosen the three set of screws on the edge of
the bubble with the supplied hex wrench.
5. Remove the bubble and the dome liner.
6. Secure the back box to the ceiling with the
supplied screws.

Installation Guide 9
Note: Please remove the rubber knockout for
cable routing outside of the camera, when
required.
7. Using a 75-ohm coaxial video cable, connect
the camera TVI video output and a TVI DVR,
and connect a 12 VDC or 24 VAC power
supply to the power cable.
8. Align the camera with the back box and tighten
the set screws to secure the camera to the
back box.

10 Installation Guide
7. Adjust the surveillance angle:
1) View the camera image on a monitor.
2) Rotate the panning table to adjust the pan
direction [0 to 355°].
3) Loosen the tilting lock screw.
4) Rotate the tilting table to adjust the tilt
direction [0 to 90°].
5) Tighten the tilting lock screw.
6) Rotate the camera lens holder [0 to 355°]
to adjust the lens to the surveillance angle.

Installation Guide 11
8. Zoom and focus adjustment.
1) View the camera image using the monitor.
2) Loosen the zoom lever and move the
screw between T (Tele) and W (Wide) to
obtain the appropriate angle of view.
3) Tighten the zoom lock screw.
4) Loosen the focus lever and move the
screw between F (Far) and N (Near) to
obtain the optimum focus.
5) Tighten the focus lock screw.
~
~
~

12 Installation Guide
Zoom
Focus
Programming
Programming on TVI output:
Once the camera hardware has been installed, you
can configure the camera settings on the TVI DVR.
TVI

Installation Guide 13
Please select PTZ protocol as TruVision Coax and
click menu button to call up the camera menu.
For more details, please see the TVI DVR user
manual.
Programming on CVBS output:
Programming on CVBS output, you need to connect
a monitor and a TVS-C200 controller (purchase
separately) as following system figure.
The TVS-C200 has one male BNC output and a
female output. Please connect the male output to
camera’s CVBS output and female output to a
monitor.
TVD-2402/TVD-4402
TVI
CVBS

14 Installation Guide
The camera has CVBS and TVI selectable video
output. Please set the built-in DIP switch to CVBS
for viewing the program on a standard monitor.
In such case, its TVI will be blocked out until you
finish the settings and change DIP switch back to
TVI.
TVD-2404/TVD-4404
The camera has the CVBS and TVI dual video
output. The built-in DIP switch is for WDR/CVBS
selection.
Please set the built-in DIP switch to CVBS for
viewing the program on a standard monitor.
When the programing is finished, you may change
the DIP to WDR to enable the WDR feature. In such
case, the CVBS output will be blocked out.
If the DIP is set as CVBS, the WDR feature will be
disabled, and the camera has CVBS and TVI output
available at the same time.

Installation Guide 15
Menu
TVD-2402/TVD-4402:

16 Installation Guide
TVD-2404/TVD-4404:

Installation Guide 17
Specifications
Power supply
24 VAC/12 VDC
Current
TVD-2402/ TVD-4402:
12 VDC: Max. 300 mA
24 VAC: Max. 210 mA
TVD-2404/TVD-4404:
12 VDC: Max. 375 mA
24 VAC: Max. 270 mA
Power
consumption
TVD-2402/ TVD-4402:
12 VDC: Max. 3.5W
24 VAC: Max. 5W
TVD-2404/TVD-4404:
12V DC: Max. 4.5W
24V AC: Max. 6.5W
Weight
(net) 641 g / 1.41 lb. (without back box)
932 g / 205 lb. (with back box)
Dimensions
Ø145.3 x 124.2 mm
(Ø5.72 x 4.89 in. )

18 Installation Guide
Legal and Regulatory
information
Copyright:
© 2015 United Technologies Corporation,
Interlogix is part of UTC Building & Industrial Systems, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and patents:
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer:
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification:
N4131
FCC compliance: Class A
Class A: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
op
erated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause

Installation Guide 19
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
ACMA compliance
Notice! This is a Class A product. In a domestic environment this
product may cause radio interference in which case the user may
be required to take adequate measures.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-0330 du Canada.
European Union directives:
12004/108/CE (EMC directive): Hereby, UTC Fire & Security declares
that this device is in compliance with the essential requirements and
other relevant provisions of Directive 2004/108/EC.
2012/19/EU (WEEE directive): Products marked
with this symbol cannot be disposed of as
unsorted municipal waste in the European Union.
For proper recycling, return this product to your
local supplier upon the purchase of equivalent new
equipment, or dispose of it at designated collection
points. For more information see:
www.recyclethis.info.
Contact information:
For contact information, see www.interlogix.com or
www.utcfssecurityproducts.eu