Interlogix TruVision TVW-2401 User manual

TruVision
HD-TVI 1080P
Wedge Camera Installation
Guide
TVW
-2401/TVW-4401
P/N 1073183-EN • REV A • ISS 07JUL16

Installation Guide 3
Content
Product overview 4
Camera description 7
Installation 8
Operating temperature range 15
Program 15
Menu tree 18
Specifications 19
Legal and Regulatory information 20

4 Installation Guide
Product overview
This is the Installation Guide for the TruVision high
definition TVI wedge camera TVW-2401/TVW-4401.
This guide describes a standard installation.
Package contents
Camera assembly
(cable harness not
shown)
3 M4 x 25 mm
screws and 3
anchors for wall or
ceiling installation
Camera drill
template
2 screws M4 x 8
used for installing
the camera to the
adapter plate

Installation Guide 5
Torx wrench Adapter plate
Adapter plate drill
template
Installation guide
CD
•Equipment disposal
instructions

6 Installation Guide
Lens adjustment
tool
HD-TVI video test
cable
12 VDC connector
(2 terminal
connectors with
positive and
negative indicators)

Installation Guide 7
Camera description
1. TVI video output
2. Power cable
3. Camera base
4. HD-TVI video test
cable
5. Menu button
Note: The HD-TVI wedge camera should only be
connected to a DVR that supports a TVI signal.
③
②
①
④⑤

8 Installation Guide
Installation
To install the camera on a surface:
1. Use the camera drill template to mark the
mounting holes.
2. Follow all local safety regulations. Drill through
the mounting surface. If you need to route the
cables from the bottom of the camera, drill a
larger hole in the mounting surface for the
cable harness.
3. Using the Torx wrench, loosen the four screws
to remove the housing cover from the device.

Installation Guide 9
4. Install the mounting base to the surface using
two of the M4 x 25 mm screws and anchors. If
routing the cable harness through the ceiling,
do so prior to mounting the camera.
5. Loosen the locking screw, located near the lens
assembly. Align the lens adjustment tool with
the two small holes located on the camera
assembly.
Rotate (pan) the camera assembly using the
lens adjustment tool until the lens is positioned
in the correct location. The tool is also used to
adjust the tilt angle.

10 Installation Guide
Note: Please do not remove the foam ring
attached to the lens. This foam ring is required
to reduce the glare of IR illuminators.
6. Tighten the locking screw and re-install the
housing cover to the camera assembly using
the Torx wrench.
Locking
Screw
Tilt
Pan
Rotation
Lens Adjustment
Tool

Installation Guide 11
To install the camera using the adapter plate:
1. Use the adapter plate drill template to mark the
holes.
2. Follow all local safety regulations. Drill through
the mounting surface. If you need to route the
cables from the bottom of the camera, drill a
larger hole for the cable harness.
130
130

12 Installation Guide
3. Install the adapter plate to the using two of the
M4 x 25 mm screws and anchors.
4. Using the Torx wrench, loosen the four screws
to remove the housing cover from the device.
5. Install the camera base to the adapter plate
using the two M4 x 8mm screws.

Installation Guide 13
6. Loosen the locking screw located near the lens
assembly. Align the lens adjustment tool with
the two small holes located on the camera
assembly.
Rotate (pan) the camera assembly using the
lens adjustment tool until the lens is positioned
in the correct location. The tool is also used to
adjust the tilt angle.
Locking
Screw

14 Installation Guide
Note: Please do not remove the foam ring
attached to the lens. This foam ring is required
to reduce the glare of IR illuminators.
7. Tighten the locking screw and re-install the
housing cover to the camera assembly using
the Torx wrench.
Tilt
Pan
Rotation
Lens Adjustment
Tool

Installation Guide 15
Operating temperature range
The operating temperature of the TVW-2401/4401
cameras is -30 to +60 °C (-22 to +140 °F).
Program
The HD-TVI video output allows the camera to be
programmed using the OSD (On Screen Display)
feature. The camera OSD can be accessed via the
recorder.
Using a TVI output
Once the camera has been installed, you can
configure the camera settings on the TVI DVR.
Connect the TVI cable to the DVR, as shown below.

16 Installation Guide
Select the PTZ protocol TruVision Coax and click
the Menu button to call up the camera menu.
For more details, refer to the TVI DVR user manual.
Call up the camera OSD (On Screen
Display) menu
To set up the camera:
1. In Camera Settings of the DVR, access the
PTZ menu and select the TruVision-Coax
protocol for the TruVision HD-TVI camera from
the drop down menu.
2. In live view of the desired camera, click the
PTZ Control icon on the live view toolbar to
access the PTZ control panel.
3. To call up the camera setup menu:
From the camera OSD of the DVR, select
Menu.
— or —
From the DVR, select Iris+.
4. Select the menu options:

Installation Guide 17
From the DVR: To select an OSD item, click
the directional buttons up/down. To adjust the
value of a selected item, click the directional
buttons left/right.
From the camera: To select an OSD item,
push the Menu button up/down. To adjust the
value of a selected item, push the Menu button
left/right.
5. Click Iris+ to enter the submenu or to confirm
the selected item.
6. When the setup is complete, select Exit and
click Iris+ to exit the camera OSD.
Note: You cannot exit the camera setup menu
using the Menu button on the camera.

18 Installation Guide
Menu tree

Installation Guide 19
Specifications
Power supply
12 VDC
Current
420 mA max.
Power
consumption
5 W max.
Weight (net)
260 g (0.57 lb.)
Dimensions
99.5 x 97 x 46.8 mm
(3.92 x 3.82 x 1.84 in. )

20 Installation Guide
Legal and Regulatory
information
Copyright:
© 2016 United Technologies Corporation,
Interlogix is part of UTC Climate, Controls & Security, a unit of
United Technologies Corporation. All rights reserved.
Trademarks and patents:
Trade names used in this document may be trademarks or
registered trademarks of the manufacturers or vendors of the
respective products.
Manufacturer:
Interlogix
2955 Red Hill Avenue, Costa Mesa, CA 92626-5923, USA
Authorized EU manufacturing representative:
UTC Fire & Security B.V.
Kelvinstraat 7, 6003 DH Weert, The Netherlands
Certification:
FCC compliance: Class A
Class A: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
op
erated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause